Removing shifter knob on 07 chevy equinox

https://www.google.com/search?q=Location+of+camshaft+position+sensor+on+2001+Mitsubishi+Montero+LIMITED+3.5+ltr&biw=1366&bih=651&tbm=isch&tbo=u&source=univ&sa=X&ved=0ahUKEwj7-rSW6p_QAhWIRyYKHcseBkIQsAQIHQ#tbm=isch&q=How+do+i+remove+shifter+knob+on+chevy+2007+equinoxes

Hope this helps

acura cd player is the last to be removed. first start with center console.
push the seats for and remove the 2 screw on the side of console,2 more inside the storage,remove shifter cover and 2 more waiting underneath.remove ashtray,more screws behind,remove center console 3-4in.and now the radio cover is free to be removed. 4 more screw holding the radio.pull slowly and disconnect the wires behind.install in revers order.
dont forget!!! Acura radio have security code.
good luck

The 4WD shifter knob on the 2007 JK's is ridiculously hard to remove. Pull straight-up with all your might, then after that fails, get some towels, and a chunk of would with a long pry bar. Hopefully you won't crack your center console.

you don't need to remove the whole console it is in sections,take a screwdriver and gently pry the front and side of the cup holder releasing the clips then pull strait up, you will see 2 phillips screws underneath remove those and pull up and back on the shifter cover, to remove the shift knob pry the lower part of the knob away from the from the top you will see 2 set screws underneath this cover then pull shifter strait up, don't forget to unplug the light for the gear selector from underside of the cover or the light assembly will break ( glued in place), the boot for the 2wd/4wd selector is held in place by 4 Phillips screws from the underside of the cover remove these and the boot stays on the selector and you can remove the cover

The center console needs to be removed, pull the shift plate plastic cover off,
remove two bolts inside the console storage box,
remove the fillips screws that are visible,
the front center storage box also has to be removed,

Front Floor Console Replacement Removal Procedure
1. Remove the console trim plate. 2. Remove the left console trim panel. . 3. Remove the right console trim panel. 4. Remove the floor console compartment.

5. If equipped with an automatic transmission, remove the 4?screws?(1), attaching the console?(2) to the shifter assembly?(3).

6. If equipped with a manual transmission, use a flat-bladed tool to disengage the retaining tabs?(1) attaching the manual transmission shifter boot assembly?(2) to the console. 7. Remove the manual transmission gear shifter knob, if necessary. 8. Remove the manual transmission shifter boot assembly?(2) from the shifter, if equipped.

9. Disconnect the console wiring connector?(1) from the inner console.

10. Remove the two nuts?(1) attaching the floor console?(3) to the vehicle floor. 11. Remove the two screws?(2) attaching the front of the console to the instrument panel assembly. 12. Remove the accessory power receptacle. 13. Lift the rear of the console upward and remove from the vehicle. 14. Remove the floor console armrest hinge, if necessary. 15. Remove the center console end panel.

16. Remove the screw?(2) attaching the floor console rear air duct?(3) to the floor console?(1). 17. Remove the floor console rear duct?(3) from the floor console?(1). 18. Remove the console storage bin, if necessary. 19. Remove the console lamp. 20. Remove the console compartment lamp switch.

Don't know the 'City' model... but if it's anything like the REGULAR Tucson, remove the shifter knob (remove access place to two phillips screws - remove screws). Remove shifter knob. Pop out shifter cover plate (snaps in and out). Remove approx 6 phillips head screws holding the metal plate above the shifter pedistal. Pop out the cosmetic cover around the radio, AC control panel and vents (wire harness connectors to digital clock, fog lamps and emergency flashers (and pass airbag light). You now have access to the phillips screws securing the audio/radio unit.

There are 2 10mm bolts in the compartment hold of the center console that must be removed. Two similar 10 mm bolts must be removed at the front of the center console, near the driver's and passenger's lower legs. The top of the center console, where the shifter is located, snaps out. With this top piece removed, the cigarette and auxilary outlet can be disconnected. Four more bolts near the shifter bracket need to be removed, and then the console is free. Hope this helps someone. I needed to remove the center console to install a component for a car stereo.

Brian

Pull off the 3 knobs for the heat controls. You will see a screw under the center knob. Remove it. Look to see if there are any screws near the vent grilles, remove them, if they are there. The whole center fascia then pulls out towards you. Remove the 4 bolts, and the radio is out. Easy.

Sisters car has the same thing. I don't think they have a bulb to light up the clock. I'm not too sure. I might try again I had to repair the aircon switch before.

How to remove the clock.

You have to remove the center console to remove the clock. (Manual car version)

-Unscrew gear knob.
-Pull out gear shifter cover surround.
-Remove cover plate with small flat blade in little tray aft of the gear stick.
-Remove 2 screws revealed by cover.
-Remove 2 screws 1 on either side of the AFT (not middle) end of the center console.
-Remove aft half of center console.
-Remove 2 screws 1 on either side fwd of air con controls.
-Remove 1 screw underneath ash tray.
-Remove hazard switch and other switch next to clock using a flat blade to pry them out.
-Unclip switches disconnect plugs.
-Remove 2 screws revealed behind switches.
-Take your time to remove fwd console / dash trim (extra screws might be there to take out).
-Disconnect clock plug.
-Remove clock.

Let me know if there is a bulb in there