1998 Chevrolet K1500 Logo

Related Topics:

Posted on Jan 24, 2010
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

My 98 has 1st and 2nd starts out in drive then nothing have to put it in 2nd to go

1 Answer

Anonymous

Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

New Friend:

An expert that has 1 follower.

Hot-Shot:

An expert who has answered 20 questions.

  • Expert 56 Answers
  • Posted on Jan 24, 2010
Anonymous
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

New Friend:

An expert that has 1 follower.

Hot-Shot:

An expert who has answered 20 questions.

Joined: Jan 12, 2010
Answers
56
Questions
1
Helped
13707
Points
170

Could be the shift solenoids in the transmission. Try pulling codes even if light is not on. Sometimes it will set a shift solenoid code if that is the problem. Very common in chevys. Good luck

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

I have a 98 chevy silverado. My transmission only has 2nd,3rd and reverse if you manually put it into 1st it still has 2nd gear in 1st&2nd gear and 3rd gear works in 3rd and drive only. Nothing higher

Remove trans pan and inspect shift solenoids. These are prone to come apart and visual inspection often finds the problem. Replacement units include a bracket to keep this from happening again.
1helpful
1answer

I have a 1999 f250 4x4 triton v10 tho odometer works now and then it shifts hard out of first and drive is like netural

Unfortunately you need a new transmission. A bad speed sensor can cause the transmission to shift hard but if it is free wheeling in 3rd gear that has nothing to do with the speedo.
0helpful
1answer

About 2 weeks ago, out of the blue, when I got off work, I put it in reverse, backed up fine, then went to accelerate forward while in drive and the RPM's just rev'd, and I didn't go anywhere. I put it in...

Sounds like the idle air control valve needs to taken off and cleaned using a non-chlorinated brake cleaner or you can replace it. Also check throttle position sensor remember whenever you replace a sensor you have to reset the computer by pulling ECM fuse out and then putting it back.
0helpful
2answers

Corolla 7a-fe tranny trouble

Have the tran fluid level checked
0helpful
1answer

I have a 1985 chevy 3/4 ton with a turbo 350 that works in all gears except drive. put it in reverse, it goes backwards. put it in 2nd, it starts off in low and shifts to 2nd, and down shifts from 2nd to...

Very possible you have a internal fault in the drive gear only.I would suggest that you remove it and have it rebuilt.We have a local company that rebuilds them for around 300 dollars.
0helpful
1answer

1994 s10 tahoe blazer.Transmission problems

You have a problem with your transmission that needs to be adressed my a good trans shop.
4helpful
2answers

Will not move from 2nd gear help PLEASE?

Your transmission is in a "limp in" mode. There are 2 sensors that need replaced. Total cost should be less than $100. I had it happen to me on my 99 300m. The sensors limit the speed to about 25 mph and the RPM rev's high. Just get the sensors replaced.
0helpful
1answer
Not finding what you are looking for?

169 views

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

john h

Level 3 Expert

29494 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...