2003 f250 6.0 diesel windshield wiper just stopped i looked for fuse they are good so changed multi function switch and wiper motor still nothing any ideas? any rlays that book doesnt say??? please help

Did you check fuse's & relays ?
Rear Window Wiper Operation
The rear wiper motor is controlled by the SJB. The SJB supplies power to the rear wiper motor from the integrated rear wiper relay. The SJB will activate the relay when all of the following conditions are met:

• Ignition switch is in the ON position
• Liftgate glass and liftgate are closed
• Multi-function switch is in the ON or intermittent position

The SJB also supplies voltage to the rear wiper motor from SJB fuse 21 (15A) when the ignition switch is in the ON position. This power feed is used to continue the wipe cycle when the multi-function switch is turned to the OFF position. The SJB receives inputs from the multi-function switch that applies ground to the low speed wipe input or applies ground to the intermittent wipe input. When either of these circuits are grounded, the SJB activates the integrated rear wiper relay and power is supplied to the rear wiper motor to move the rear wiper motor from the park position. An internal switch in the rear wiper motor then moves to the run position which connects the accessory relay power to the rear wiper motor. When the rear wiper motor returns to the park position, the internal switch in the rear wiper motor moves back to the park position. If the multi-function switch is in the ON position, the rear wiper relay is still activated, power is supplied to the rear wiper motor, and the wipe cycle starts again. If the multi-function switch is in the intermittent position, the rear wiper relay does not activate until the predetermined dwell time has elapsed, at which time the SJB activates the rear wiper relay and the wipe cycle starts again. The SJB is the smart junction box .(computer )

Rear Washer System
The SJB supplies power to the rear washer pump from fuse 21 (15A) when the ignition switch is in the ON or ACC position. The rear washer pump receives ground from the multi-function switch when the wash function is turned ON. The multi-function switch also signals the SJB when the rear wash is activated and the SJB then activates the rear wiper.

Have a qualified repair shop check it out . Electronic module involved , WCM - wiper control module . May have code's stored . You have no clue as to how it works.

The windshield wipers are controlled by the wiper control module and the driver-operated multi-function switch on the steering column, with the ignition switch in RUN or ACC position.
There are four modes of wiper operation: OFF position, the wipers move to and stay in the park position; Interval position, the wiper control module causes the wipers to cycle, separated by pauses, pause time length being determined by switch location; LO position, the wipers will operate at low speed continuously; HI position, the wipers will operate at high speed continuously.
The windshield washers are controlled by pressing inward on the wiper switch end of the multi-function switch. The washers will operate as long as the switch is depressed. If the wipers are in the OFF or Interval operating mode, the wipers will begin in LO speed and the washer pump will pump fluid from the reservoir to the nozzles. When the switch is released, the wipers will complete three cycles and then return to their previous setting. In LO or HI mode, no change in wiper operation will occur during washer operation.
The washer fluid level sensor is in the windshield washer reservoir (17618) and is monitored by the hybrid electronic instrument cluster (HEC) and displays a WASHER message when the fluid level is low. The washer fluid level sensor and windshield washer reservoir are replaced as an assembly.

• The Low Wiper Speed Does Not Operate Properly

• Multi-function switch.
• Wiper motor.
• Circuitry.
• Wiper control module.

• GO to Pinpoint Test C .

• The High Wiper Speed Does Not Operate Properly

• Multi-function switch.
• Wiper motor.
• Circuitry.
• Wiper control module.

• GO to Pinpoint Test D .

Highly doubtful it being a blown fuse . Fuse's don't just blow , short circuit to ground or high current draw . Faulty component , wiper motor , wiper control module more likely . Free wiring diagrams here http://www.bbbind.com/free-tsb Enter vehicle info. year , make , model an engine size . Under system click on body & accessories . then under subsystem click on wiper / washer , Click the search button ,then the blue link . Looking at the diagram i see the wiper switch is a input to the wiper control module .

The windshield wipers are controlled by the wiper control module and the driver-operated multi-function switch on the steering column, with the ignition switch in RUN or ACC position.
There are four modes of wiper operation: OFF position, the wipers move to and stay in the park position; Interval position, the wiper control module causes the wipers to cycle, separated by pauses, pause time length being determined by switch location; LO position, the wipers will operate at low speed continuously; HI position, the wipers will operate at high speed continuously.
The windshield washers are controlled by pressing inward on the wiper switch end of the multi-function switch. The washers will operate as long as the switch is depressed. If the wipers are in the OFF or Interval operating mode, the wipers will begin in LO speed and the washer pump will pump fluid from the reservoir to the nozzles. When the switch is released, the wipers will complete three cycles and then return to their previous setting. In LO or HI mode, no change in wiper operation will occur during washer operation.
The washer fluid level sensor is in the windshield washer reservoir (17618) and is monitored by the hybrid electronic instrument cluster (HEC) and displays a WASHER message when the fluid level is low. The washer fluid level sensor and windshield washer reservoir are replaced as an assembly.

• The Wipers are Inoperative

• Fuse.
• Wiper motor.
• Multi-function switch.
• Circuitry.
• Wiper control module.

• GO to Pinpoint Test B .

PINPOINT TEST B: THE WIPERS ARE INOPERATIVE CONDITIONS DETAILS/RESULTS/ACTIONS B1 CHECK FUSE JUNCTION PANEL FUSE 16 (30A)
Fuse 16 (30A)

• Is the fuse OK?

Yes GO to B2 .

No REPLACE the fuse. TEST the system for normal operation. If the fuse fails again, CHECK for a short to ground. REPAIR as necessary. B2 CHECK FOR VOLTAGE TO THE WIPER CONTROL MODULE - CIRCUIT 65 (DG)
Wiper Control Module C294
Measure the voltage between wiper control module C294-2, circuit 65 (DG), and ground; and between wiper control module C294-11, circuit 65 (DG), and ground.

• Is the voltage greater than 10 volts?

Yes GO to B3 .

No REPAIR circuit 65 (DG). TEST the system for normal operation. B3 CHECK CIRCUIT 57 (BK) FOR OPEN Measure the resistance between wiper control module C294-3, circuit 57 (BK), and ground; and between wiper control module C294-5, circuit 57 (BK), and ground.

• Are the resistances less than 5 ohms?

Yes GO to B4 .

No REPAIR circuit 57 (BK). TEST the system for normal operation. B4 CHECK THE MULTI-FUNCTION SWITCH
Multi-Function Switch
Check the multi-function switch; refer to Section 211-05 .

• Is the multi-function switch OK?

Yes GO to B5 .

No REPLACE the multi-function switch; REFER to Section 211-05 . TEST the system for normal operation. B5 CHECK CIRCUIT 993 (BR/W) FOR OPEN Measure the resistance between multi-function switch C269-4, circuit 993 (BR/W), and wiper control module C294-7, circuit 993 (BR/W).

• Is the resistance less than 5 ohms?

Yes GO to B6 .

No REPAIR circuit 993 (BR/W). TEST the system for normal operation. B6 CHECK CIRCUIT 589 (O) FOR OPEN Measure the resistance between multi-function switch C269-1, circuit 589 (O), and wiper control module C294-1, circuit 589 (O).

• Is the resistance less than 5 ohms?

Yes GO to B7 .

No REPAIR circuit 589 (O). TEST the system for normal operation. B7 CHECK THE WIPER CONTROL MODULE OUTPUT FOR VOLTAGE
Wiper Control Module C294

Wiper Motor C152
Turn the multi-function switch to the HI position. Measure the voltage between wiper motor C152-4, circuit 57 (BK), and wiper motor C152-3, circuit 56 (DB/O).

• Is the voltage greater than 10 volts?

Yes REPLACE the wiper motor; REFER to Motor-Windshield Wiper . TEST the system for normal operation.

No GO to B8 . B8 CHECK CIRCUIT 57 (BK) FOR OPEN Measure the resistance between wiper motor C152-4, circuit 57 (BK), and ground.

• Is the resistance less than 5 ohms?

Yes REPLACE the wiper control module; REFER to Module-Windshield Wiper . TEST the system for normal operation.

No REPAIR circuit 57 (BK). TEST the system for normal operation.

1997 mercury wagon ? Sable ? VISUAL INSPECTION CHART-WINDSHIELD WIPER AND WASHER SYSTEMS Mechanical Electrical

• Windshield wiper blade missing or damaged.
• Binding windshield wiper pivot arm.
• Binding windshield wiper mounting arm and pivot shaft.
• Empty windshield washer reservoir.
• Kinked or broken windshield washer hoses.

• Open fuse junction panel Fuses:
  • 8 (5A)
  • 12 (5A)
  • 20 (5A)
  • 23 (5A)
• Damaged windshield wiper motor.
• Damaged windshield washer pump.
• Open connectors.
• Corroded connectors.
• Inoperative multi-function switch.
• Open thermal breaker internal to the wiper motor

Which are not working , front , back or all ?

I/P Fuse Panel C225
Under left corner of instrument cluster

Wd40 of gt85 tray that first

The wiper control module is probably at fault ,without test that is just a guess . The wiper/washer switch is a input to the wiper control module. Do you know anything about automotive electronics an electrical systems ?

• The Wipers are Inoperative

• Fuse.
• Wiper motor.
• Multi-function switch.
• Circuitry.
• Wiper control module.

• GO to Pinpoint Test B .

Voltage drop testing the power an ground circuits for the wiper control module would be a good place to start . Do you know how to test electrical circuits with a volt meter ?
PINPOINT TEST B: THE WIPERS ARE INOPERATIVE CONDITIONS DETAILS/RESULTS/ACTIONS B1 CHECK FUSE JUNCTION PANEL FUSE 16 (30A)
Fuse 16 (30A)

• Is the fuse OK?

Yes GO to B2 .

No REPLACE the fuse. TEST the system for normal operation. If the fuse fails again, CHECK for a short to ground. REPAIR as necessary. B2 CHECK FOR VOLTAGE TO THE WIPER CONTROL MODULE - CIRCUIT 65 (DG)
Wiper Control Module C294
Measure the voltage between wiper control module C294-2, circuit 65 (DG), and ground; and between wiper control module C294-11, circuit 65 (DG), and ground.

• Is the voltage greater than 10 volts?

Yes GO to B3 .

No REPAIR circuit 65 (DG). TEST the system for normal operation. B3 CHECK CIRCUIT 57 (BK) FOR OPEN Measure the resistance between wiper control module C294-3, circuit 57 (BK), and ground; and between wiper control module C294-5, circuit 57 (BK), and ground.

• Are the resistances less than 5 ohms?

Yes GO to B4 .

No REPAIR circuit 57 (BK). TEST the system for normal operation. B4 CHECK THE MULTI-FUNCTION SWITCH
Multi-Function Switch
Check the multi-function switch; refer to Section 211-05 .

• Is the multi-function switch OK?

Yes GO to B5 .

No REPLACE the multi-function switch; REFER to Section 211-05 . TEST the system for normal operation. B5 CHECK CIRCUIT 993 (BR/W) FOR OPEN Measure the resistance between multi-function switch C269-4, circuit 993 (BR/W), and wiper control module C294-7, circuit 993 (BR/W).

• Is the resistance less than 5 ohms?

Yes GO to B6 .

No REPAIR circuit 993 (BR/W). TEST the system for normal operation. B6 CHECK CIRCUIT 589 (O) FOR OPEN Measure the resistance between multi-function switch C269-1, circuit 589 (O), and wiper control module C294-1, circuit 589 (O).

• Is the resistance less than 5 ohms?

Yes GO to B7 .

No REPAIR circuit 589 (O). TEST the system for normal operation. B7 CHECK THE WIPER CONTROL MODULE OUTPUT FOR VOLTAGE
Wiper Control Module C294

Wiper Motor C152
Turn the multi-function switch to the HI position. Measure the voltage between wiper motor C152-4, circuit 57 (BK), and wiper motor C152-3, circuit 56 (DB/O).

• Is the voltage greater than 10 volts?

Yes REPLACE the wiper motor; REFER to Motor-Windshield Wiper . TEST the system for normal operation.

No GO to B8 . B8 CHECK CIRCUIT 57 (BK) FOR OPEN Measure the resistance between wiper motor C152-4, circuit 57 (BK), and ground.

• Is the resistance less than 5 ohms?

Yes REPLACE the wiper control module; REFER to Module-Windshield Wiper . TEST the system for normal operation.

No REPAIR circuit 57 (BK). TEST the system for normal operation.

Wire connection are the only thing left to check. But then again multi function may not be operational you just a have to ck connections motor for wiper may be bad also

If the fuses are OK, then two choice to check there:
* Faulty Wiper Motor.
Check if activated switch, you have voltage in the wires wiper motor; if have voltage, then the motor is bad. If dont have voltage, then switch is bad.

* Faulty Wiper Switch.
The multi-function switch cannot be adjusted or repaired. If any function of the switch is faulty, or if the switch is damaged, the entire switch unit must be replaced.

Hope helps; keep us updated.

Check Engine light and Wipers are not interconnected. For Check Engine light, there may be some sensor signal problem.

For wipers, if the fuses are good, then you have to look out burnout wiper motor. Check for the multi-function switch to operate the wipers may lost its contact points or any wiring cut.

You might have a bad wiper motor, you can try checking for voltage at the wiper motor connector, if your getting voltage at the connector replace the wiper motor.