2002 Volkswagen Jetta TDI Logo

Related Topics:

Anonymous Posted on Apr 09, 2010

Serp belt installation Can I install a short belt if I do not run the AC pump and how is it routed?

  • Anonymous Apr 09, 2010

    The car has 322,000 km on it.
    The clutch bearing is gone on the AC pump, new pump is $$$$$$.
    Just need routing for short serp belt on none AC car.

  • Anonymous May 11, 2010

    why would you want to NOT have AC???

×

1 Answer

Anonymous

Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Sergeant:

An expert that has over 500 points.

  • Expert 152 Answers
  • Posted on Apr 09, 2010
Anonymous
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Sergeant:

An expert that has over 500 points.

Joined: Apr 07, 2010
Answers
152
Questions
0
Helped
60453
Points
505

Yes you can run a shorter belt. You will have to measure how many inches you need to get the right size belt. The routing should be pretty much the same you just skip the AC pump and route the belt as usual. The auto parts store may carry the belt of you ask for a no-ac option when making your purchase.

  • Anonymous Apr 09, 2010

    Well since your vehicle came equipped with factory air then running a short belt would be considered a custom application. It is a little hard to tell you the exact routing without being able to see the vehicle. It shouldn't be too hard however, if you follow the routing diagram under the hood and just bypass the routing for the ac compressor it should go on pretty much the same way. I understand about the compressor costing dollars I have a passat and everything on a VW is grossly overpriced. If you would like you can try these websites as they offer low cost alternatives to manufactures parts. Rockauto.com offers OEM replacement parts at a discounted price and car-part.com is a parts listing of all salvage yards in the US and most of them will ship a part to you. You may be able to pick up a compressor on the cheap from one of these sources.

×

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Do you have a routing diagram of a serpentine belt for a 2010 VW Passat 2.0 T ?

PS belt (and AC? and GEN?) ALL 3 are now dead:
the water pump has its own cog belt too (aka serp)??????
USA CAR? or NOT, cars are not the same all over earth you posted to a public world wide forum and no country told at all,
with AC or no AC (cooling) >???>??????
do not drive any car if the water pump belt slips off , snaps or is missing or train wreck the engine you will . but yours is pump cog belt no
the car many have map sticker on the front of the car hood up
did you look first.
answers me are USA only,
we have 3 version of the 2.0 and only version A,M,D not T
so you not here? all 3 our ours have 3 belt types.
I thinks you are confused, and the missing belt runs many thing
GEN-G
PS ?
AC compressor.
E = engine crank pulley
here is ours 2.0L M
there is no PS pump this PS is electric motor drive
Electromechanical power steering motor!



vw-undefined-undefined-0.jpg

vw2-undefined-undefined-2.jpg

vw2-undefined-undefined-1.jpg I will not cover the waterpumps, some have 2. even. cool down pumps., I will skip WP(and has its own belt)
1helpful
1answer

Belt replacement mazda3 2006

i do hope this helps its for the serpentine belt
First, jack up the caricon1.png, use jack stands, yadda yadda etc.

Remove the lower splash shield.

Youll see a skid plate looking thing on the ac compressor, remove that with a 12mm socket.

Now you have to remove the AC compressor. There are four stud/bolt things holding it on. Also 12mm.

Once the bolts are out the AC compressor is basically held up by the belt and the AC lines. Work the AC belt off of the pulley and then secure the ACcompressor out of the way. Dont let it hang by the AC lines.

Go back up to the top of the engine and remove the engine cover, it just pulls right off.

Youll see the serpentine belt and the tensioner pulley (basically the pulley at the front of the motor and right on top).

Note the routing of the belt for reinstallation.

Put a socket on the tensioner pulley (either 12 or 14mm) and push towards the firewall.

Youll see the belt loosen.

Now slip the belt off of the tensioner pulley.

You can release the tension on the pulley slowly now.

Work the serp belt off of the rest of the pullies.

Installation is basically the reverse of removal, but it can be tricky to route the belt on since its new and rigid. It helps to have a friend push on the tensioner while you route the belt. I managed to do it by myself, but I have long arms. It also took me several tries and much swearing!

Now putting the AC belt back on can be tricky due to the fact that it is a stretch belt, and will be very tight.

I slipped the belt on the crank pulley and then pulled the AC compressor up as high as I could. Then I could slip the belt on. Little note here, because the belt was so tight the compressor wouldnt slip back into position. I used my floor jack on the bottom of the compressor and very slowly pushed on it with the jack.

Then line up the AC compressor, resecure the bolts/nuts etc.

Reinstall splash shield.

DONE
0helpful
1answer

How to replace 2002 camry drivebelt

to replace the serp belt you'll need to release the tensioner in the system remove the old and install the new the issue always is the proper routing for the belt follow the diagram under the hood watch the routing as you remove the old belt if a diagram isn't available under your hood request one upon the purchase of your new belt sometimes the parts store will loan or rent you the tools you need for belt replacement
2helpful
1answer

Install 2003 pontiac montana serpentine belt

The serp belt tensioner will be in between the alternator and the power steering pump. Use a 3/8 ratchet and insert it into the square hole of the tensioner. Rotate the tensioner to remove the tension from the belt.

It doesn't hurt to draw a picture of the belt routing before removing the belt. Most GM's will have a diagram of the belt routing. I think yours is located on the plastic cover that is near the water pump.

If you don't have a diagram the belt is routed like this.

From the crank pulley the blet goes to the a/c compressor then under the water pump pulley then over the power steering pump and the alternator. then down to the p/s pump, over the tensioner pulley and finally ending up at the crank pulley.

Let me know if you have any question and I'll be happy to help. Thank you for using fixya.com!

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

0helpful
1answer

How do you take of a drive belt on a 2005 nissan altima 3.5 sl?

its easier if you have a serp belt tool from the parts store the tensioner is at the top using the tool rotate it one way or the other and the belt will loosen up remove the belt rout the new belt and use the tool to rotate it to install on last pulley hers a pic so you dont forget how it is routedonetufshoppe_29.gif
13helpful
2answers

Serp.belt route diagram for 98 audi a4 quattro 2.8

The serpentine belt routing diagram for 1998 Audi A4 Quattro 2.8 liters V6 engine:

tdisline_45.jpg


CS = Crankshaft
F = Fan pulley
Gen = Alternator
T = Tensioner pulley
AC = Air Conditioning
PAS = Power Assisted Steering

1helpful
1answer

HOW TO INSTALL SERP BELT ON 07 SUZUKI FORENZA

Raise vehicle, support with safety latches/jackstands, remove splash guard from passenger front wheel well. Using a box-end 15mm wrench release tension from automatic tensioner. Noting belt routing, remove serpentine belt, replace with new one, reinstall splash guard.
7helpful
1answer

Dodge 2000 minivan,water pump leaking

Make sure it's cool, pop the radiator cap, Remove the shield on the passenger side between the tire and front of engine. Relieve the tension on the serp belt,draw yourself a diagram of the pulleys and belt routing in case the sticker is gone on the strut tower, remove the serp belt. Take the bolts out of the pulley on the front of the water pump (3). Remove the lower radiator hose at the front cover to drain the coolant. Remove the 6 mm bolts holding the water pump to the front cover housing. tap on the pump with a rubber hammer. Install a new gasket on the new pump, and a weap hole diverter in the pump (round black about hte size of a quarter), use old one if there's no new one. Install pupm and tighten bolts snug with a 1/4" ratchet. Install pulley and 3 bolts. Install belt, top off radiator with 50/50 mix green coolant. start engine and run to operating temperature,make sure the belt is seated in all of the pulleys and is running true, radiator fans should come on. Shut engine down and let cool overnight. Check level in radiator and overflow bottle, top off as necessary.
4helpful
2answers

Serpentine belt diagram for a dodge durango 1999

hey go here and look at picture 7-20

http://www.daycoproducts.com/daycoweb.nsf/Serp%20Rout%20Guide%20Illus.pdf
Not finding what you are looking for?

233 views

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Bradley
Bradley

Level 2 Expert

105 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...