Traction control button 2007 ls equinox

Service Stabilitrak, Traction Control lights ON, alone with check ...

chevroletforum.com > ... > Equinox

Jul 9, 2012 - Service Stabilitrak, Traction Control lights ON, alone with check engine light. ... 2007 Chevy Equinox LT FWD 2007 Saturn Ion 2 Quad Coupe ... HELP - Service Stabilitrak & Service Traction Control
Aug 30, 2011
Service Traction Control - Stabilitrak and ABS light, Help ...
Feb 12, 2011
Stabilitrak Off Message + lost Power stearing
May 31, 2009
More results from chevroletforum.com

Chevy Equinox Eco, Traction Control and Stabilitrak Systems

? 2:39
https://www.youtube.com/watch?v=15Qj4HzpBz0

there should be one speed sensor for every wheel some speed sensors are located in the wheel hub

Traction control uses the engine along with other components, so if the engine is not working correctly the traction control system can be disabled too.
You would need to get the computer scanned for codes to proceed.

Do you have a check engine light on? If so, get the codes using an OBD2 checker and see if the stabiltrak or/and the traction control are having problems. If not, pull the wheels and check the condition of ALL the brakes. Only one needs to be grabbing to give that effect.

Your vehicle has electric power steering !
The Electric Power Steering (EPS) system reduces the amount of effort needed to steer the vehicle. The system uses the power steering control module (PSCM), torque sensor, power steering motor rotational sensor, power steering motor, discrete battery voltage supply circuit, and the GMLAN serial data circuit to perform the system functions. The PSCM and power steering motor are each serviced separately from the steering column assembly. However, the motor rotational sensor is serviced as part of the power steering motor, and the torque sensor is serviced as part of the steering column assembly. The PSCM also monitors vehicle speed from the engine control module (ECM) via the GMLAN serial data circuit. At low speeds more assist is provided for easy turning during parking maneuvers. At higher speeds less assist is provided for improved road feel and directional stability.
Stability System Indicator The IPC illuminates the stability system caution indicator when one or more of the following conditions exists. The EBCM sets any one of many VSES-disabling DTCs. The EBCM sends a serial data message to the IPC requesting illumination.
Traction Control System Indicator
TRAC OFF The instrument panel cluster (IPC) illuminates the TRAC OFF indicator when the following occurs:
?€¢
The electronic brake control module (EBCM) inhibits the traction control system due to a malfunction in the traction control system. The IPC receives a serial data message from the EBCM requesting illumination.

?€¢
The Body Control module (BCM) detects that the traction control switch has been pressed (signal circuit is low). The Body Control module (BCM) sends a serial data message to the EBCM in order to disable traction control. The IPC receives a serial data message from the EBCM requesting illumination. The BCM sends a serial data message to the radio in order to activate an audible warning.

Your best bet is to take it to a ASE certified an qualified repair shop ,that has the diagnostic tool to fix this problem .

the tire pressure sensor has nothing to do with traction control. need to have system scanned and see what codes are in it and we can go from there

You need to have the system scanned, the traction & stabilty control receive thier input from the wheel sensors. This also is linked to the anti-lock brake system.

That would be your computer system trying to tell you that there is a malfunction in your traction and stability control system. You will have to access the computer data in order to find out the nature of the failure and to diagnose the problem.

either you have the wrong cv axle and it has no triger wheel or the speed sensor wea damaged while changing axle.

Is it under warantee?