How do I remove fuel pump from dodge 1998 1500

About 117,000 results (0.73 seconds) Search Results

TIPM Repair & Bypass Solutions for 2007-2014 Dodge ...

www.verticalvisions.com/TIPM_solutions.php
2011-2012 Dodge Ram 1500; 2011-2012 Dodge Ram 2500; 2011 Chrysler Town ... test your fuel pump relay, and bypass a bad fuel pump relay to stay on the road. .... Mytesting/bypass device will often narrow down your problem to the TIPM ...

Dodge Ram 1500 Questions - fuel pump keeps running ...

www.cargurus.com > Questions > Dodge > Ram 1500

CarGurusNov 1, 2013 - fuel pump keeps running when key removed - 2011 ram 1500 slt quad ...fires right up but will not stay running unless I keep my foot on the gas.

I Changed The Fuel Pump On My 97 Dodge Ram 1500. Ran ...

www.cargurus.com > Questions > Dodge > Ram 1500

CarGurusI changed the fuel pump on my 97 dodge ram 1500. Ran great for 2 days then stopped running. I can hear pump working, replaced fuel system relay, engine tur... ...Jun 24, 2012 at 03:48 PM about the 1997 Dodge Ram 1500 2 Dr ST 4WD ... The truck fires right up but will not stay running unless I keep my foot on the gas.

2011 Dodge Durango Fuel Pump Relay Stays Engaged ...

www.carcomplaints.com/Dodge/.../fuel.../fuel_pump_relay_stays_engag...

Fuel pump
REMOVAL

1. Disconnect the battery ground cable.
2. Disconnect the fuel inlet, outlet and return hoses at fuel pump.
3. Remove the two fuel pump mounting bolts, and remove the fuel pump.
4. Remove the fuel pump gaskets and insulator.

Check for leakage, if there is oil or fuel leaking from the breather hole, oil seal or diaphragm of fuel pump, the pump is defective. Replace fuel pump as an assembly.

INSTALLATION

1. Turn the crankshaft so the No. 1 cylinder is at top dead center on the compression stroke. NOTE : This is to minimize cam lift for ease of installation.
2. Insert the push rod into the cylinder head.
3. Install the new gasket and insulator, install the fuel pump.
4. Tighten the bolts firmly.
5. Connect the fuel hoses to the fuel pump ******* and tighten the hose clamps.
6. START the engine.
7. Check for fuel or oil leaks.

Trying to find?

Best Way?

Almost all fuel pumps are in the fuel tank

You have no choice but to remove the tank,
then remove the pump from the top.

A'm I missing the question?

first check the fuse box to see if there are fuses for the fuel pump, and also check to see if there is a fuel pump relay...if fuses are good..then have someone turn the key on while you listen to the fuel pump relay...it should click when the key is turned.....if this works then there may be the possibility that the fuel; pump is defective...you can try hitting the fuel tank with a rubber mallet and see if the fuel pump starts working again...a lot of dodge fuel pumps will become intermittant(I have had several dodge p/u trucks do this) and if you pound on the fuel tank ...sometimes they will start working again....if it starts working, then you will need to change it..because it will only happen again...and probably at the most inconvenient time...to change the fuel pump you will either need too remove the bed of the truck(which I find is the easiest way) to get to the top of the fuel tank. Or , you can remove the straps that hold the fuel tank up...the only problem with this is if the tank is full then it is going to weigh somewhere around 250 pounds...best way is to remove the bed....on top of the fuel tank is the "fuel deliver module"...as dodge refers to it as...there is a large "C" clip that holds the unit in the tank...you need to remove the clip with a flat blade screwdriver and then the module will pop up...be careful when removing the unit as there is a float assembly that may be damaged when you remove the assembly.....sometimes you may be able to obtain just the fuel pump(depending on model) and sometimes you may have to replace the whole delivery module, which is rather expensive...then reassemble is revers order

Either jack up the truck and drop the tank risking need of more repairs to straps or remove bed from truck and do it while the tank is still on the truck .
I have in the past with old rusted beaters cut a hole in the bed of the truck to access the fuel pump and put the bedliner back in so I didnt see the hole.

A fuel pressure test will tell you if the pump is performing as it should, the first step would be to scan the computer to see what the code or codes are. Has the vehicle had a tune up recently if ever?

Try to reset fuel pump switch, and check for cloged fuel filter!

Go to the autozone website at autozone.com and register your vehicle. It's free and will give you access to an online repair manual for your vehicle. The procedures for changing out the fuel pump can be found there. ( I checked). Hope this helped and best wishes.

Tried changing the fuel filter? If that's not it it could be a bad pump

You have to remove the fuel tank.