I just did a rear brake service with new brake shoes and now my e brake lever in the drivers side goes all the way to the floor before getting tight

Was the brake shoes replacement a DIY or professional job. If DIY, are you certain that you reassembled the brakes properly? Does the truck move at all? Does it feel as though the e-brake is applied? With the e-brake pedal to the floor, the truck should not move freely when the accelerator pedal is depressed. The emergency brake assemblies on both rear wheels are connected to a cable assembly that ultimately leads to the e-brake pedal. The cable has an adjustment point and a spring tensioner to prevent slack in the cable. First, crawl under and physically check the cable tension. If it's loose, either the cables are not connected to the rear wheels' brake assemblies, not connected properly, or the cable and/or pedal is damaged/broken. If the cable is tight - overly tight, but the e-brake is not holding the truck from moving, the e-brake levers attached to the shoes inside the brake drums are likely not installed correctly. Double check your installation and consider replacing the e-brake cable (as a precaution). As for the pedal, you may have to remove it in order to get the ratchet-locking mechanism to release.
Of course, if this was a professional job, call the shop and have them make it right. Good luck.

Removal
1.Remove rear wheel and tire assembly from vehicle.

2.Remove rear brake drums from hub and bearing assemblies after loosening the two brake drum screws.

3.Be sure that the parking brake pedal is in the release(most upward) position.

4.Completely loosen square nut of the rear parking brake cable. Then create slack in the rear parking brake cables.

5.Remove adjuster spring from adjust lever and brake shoe.

6.Remove adjust lever and turn the adjusting wheel of adjuster assembly to the direction of the arrow as shown.

7.Remove the strut spring and the lower retracting spring from the brake shoe.

8.Remove the upper return spring from the brake shoe.

9.Remove brake back plate hold down spring and pin from the leading brake shoe assembly.

10.Remove the leading brake shoe. Then remove the adjuster assembly, strut and anchor spring from the trailing brake shoe.

11.Remove the trailing brake shoe from the brake back plate after removing hold down spring and pin.

12.Remove the trailing brake shoe from the rear parking cable.

13.Remove parking pivot lever from the leading brake shoe.

Replacement
1.Lubricate the eight shoe contact areas on the back plate and anchor.

2.Install the trailing brake shoe to the rear parking cable.

3.Install trailing brake shoe on brake back plate and install the trailing brake shoe hold down spring and pin on the brake shoe.

4.Tighten the square nut of rear parking cable.

5.Install the anchor spring then install adjuster assembly, and strut.

6.Install leading brake shoe on brake back plate.

7.Install the brake shoe upper return spring, strut spring and the lower retracting spring to the brake shoe.

8.Properly rotate the adjusting wheel of adjuster assembly to the direction of the arrow in as shown.

9.Install the adjuster spring on the adjust lever and leading brake shoe assembly.

10.Install the leading brake shoe hold down spring and pin on the brake shoe.

11.Adjust brake shoes assemblies so as not to interfere with brake drum installation.

12.Install the rear brake drums on the hubs.

13.Check and adjust whether the pedal stroke in the specification.(Refer to section BR Gr./On-vehicle service/Pedal stroke of parking brake)

14.Install wheel and tire.

15.Push the parking brake pedal to the floor once and release pedal. This will automatically remove the slack from and correctly adjust the parking brake cables.

16.Test the vehiche on the road. The adjust will continue the brake adjustment during the road test of vehicle.

Inspection
1.Inspect the disassembled parts for wear, rust or damage.

2.Measure the thickness of brake shoe lining.
Standard : 0.17 in (4.5 mm)
Minimum : 0.04 in (1 mm)

3.If the shoe lining is less than minimum or shows signs of uneven wear, replace new one.

4.Measure the inside diameter of the brake drum.
Standard : 10 in (254 mm)
Maximum : 10.07 in (256 mm)

5.If the inside diameter of the brake drum is more than maximum or shows signs of uneven wear, replace new one.

6.Inspect the lining and drum for proper contact. If the contact condition is improper, repair it with a grinder or replace the brake shoe assembly.

Make sure you have lots of "meat" on your brake shoes.
Emergency brakes only apply rear brakes by using shoes against the drum, that are pulled by the cable, that's attached to the emergency brake lever / pedal....and actuated by the driver.

It has to be one of those three components...may have to pull the drum and actuate the pedal / lever to see if the cable spreads the shoes and make adjustments from there.

If your back brakes don't hold...it can also cause the ABS light to illuminate...

Hope this helps...

The rear brake drums are drum brakes on the 94 excel. The Excel uses the front brakes the most, so are you sure you need to replace the rear brakes?

REMOVAL & INSTALLATION
It is a good idea to only disassemble and assemble one side at a time, leaving the other side intact as a reference.

1. Raise and support the vehicle safely.
2. Remove the brake drum.
3. Disconnect the parking brake rear cable and conduit.
4. Remove the brake shoe hold-down springs and brake shoe hold-down pins.
5. Remove the brake shoe adjusting screw spring.
6. Remove the brake shoe adjusting lever and adjuster screw.
7. Remove the brake shoe retracting spring.
8. Remove the brake shoes from the backing plate.
9. Remove and discard the parking brake lever clip. Remove the washer.
10. Remove the parking brake lever from the rear brake shoe.

To install:

1. Thoroughly clean the backing plate with brake cleaning solvent and dry completely.
2. Use silicone grease to lubricate the brake backing plate-to-brake shoe contact areas.
3. Apply a light coating of premium grease to the threaded areas of the adjuster. Turn the adjuster in and out to spread the lubricant. Turn the adjuster all the way down on the screw and loosen one-half turn.
4. Install the parking brake lever to the rear (secondary) brake shoe with a new clip.
5. Position the brake shoes on the backing plate and install the brake shoe hold-down springs.
6. Attach the parking brake rear cable and conduit to the parking brake lever.
7. Attach the brake shoe retracting spring.

The socket end of the brake adjuster screw is stamped with "R" or "L" to indicate that it is to be installed either on the right (passenger's side) or left (driver's side) of the vehicle. The adjuster nuts can be distinguished by the number of grooves machined around the body of the nut. Two grooves indicate a right-hand adjuster nut and one groove indicates a left-hand adjuster nut. Another way to identify brake adjuster assemblies is to check thread pitch. The right side adjuster assembly has right-hand threads and the left side has left-hand threads. If installed correctly, the brake adjuster assembly will increase in length when the brake shoe adjusting lever is operated.

1. Install brake adjuster screw in the slots on the brake shoes. The wider slot on the socket end must fit in the slot on the front (primary) brake shoe.
2. Install the brake shoe adjusting lever on the lever pin.
3. Install the brake adjusting screw in the slot on the secondary brake shoe and in the slot on the brake shoe lever. The brake shoe adjusting lever should contact the brake adjuster screw.
4. Adjust the brake shoes.
5. Install the drums.

ADJUSTMENTS

The drum brakes are self-adjusting and require a manual adjustment only after the brake shoes have been replaced, or when the length of the adjusting screw has been changed while performing some other service operation.
Drum Installed

1. Raise and support the vehicle safely.
2. Remove the rubber plug from the adjusting slot on the backing plate.
3. Insert a Brake Adjustment Tool (D81L-1103-C) or equivalent into the slot and engage the lowest possible tooth on the starwheel. Move the end of the brake spoon downward to move the starwheel upward and expand the adjusting screw. Repeat this operation until the brakes lock the wheels.
4. Insert a small screwdriver or piece of firm wire (coat hanger wire) into the adjusting slot and push the automatic adjusting lever out and free of the starwheel on the adjusting screw and hold it there.
5. Engage the topmost tooth possible on the starwheel with the brake adjusting spoon. Move the end of the adjusting spoon upward to move the adjusting screw starwheel downward and contract the adjusting screw. Back off the adjusting screw starwheel until the wheel spins freely with a minimum of drag. Keep track of the number of turns that the starwheel is backed off, or the number of strokes taken with the brake adjusting spoon.
6. Repeat this operation for the other side. When backing off the brakes on the other side, the starwheel adjuster must be backed off the same number of turns to prevent side-to-side brake pull.
7. When the brakes are adjusted, make several stops while backing the vehicle to equalize the brakes on both of the wheels.
8. Lower the vehicle.

Drum Removed
See Figure 2

Fig. Fig. 2: When using a brake adjustment gauge, first measure the inside diameter of the drum (top) and then adjust the brakes shoes to the proper outside diameter (bottom)

1. Remove the brake drum.
2. Make sure that the shoe-to-contact pad areas are clean and properly lubricated.
3. Using a Brake Adjustment Gauge (D81L-1103-A) or equivalent, check the inside diameter of the drum.
4. Measure across the diameter of the assembled brake shoes, at their widest point.
5. Turn the adjusting screw so that the diameter of the shoes is 0.030 in. (0.76mm) less than the brake drum inner diameter.
6. Install the drum.

INSPECTION

See Figure 3

Fig. Fig. 3: Measure brake shoe thickness in several places around the shoe
Inspect the brake shoes for wear using a ruler or Vernier caliper. Compare measurements to the brake specifications chart. If the lining is thinner than specification or there is evidence of the lining being contaminated by brake fluid or oil, replace all brake pad assemblies (a complete axle set).

If the following is not enough then maybe try Alldata.com which generally has more information, but it will cost: REMOVAL & INSTALLATION Chrysler Concorde, New Yorker, LHS Dodge Intrepid Eagle Vision

1. Remove the rear wheels and brake drums.
2. Remove the dust cap from the rear hub and bearing assembly.
3. Remove the cotter pin, nut retainer and wave washer. Discard the old cotter pin.
4. Remove the rear hub and bearing assembly retainer nut and washer. Remove the rear hub and bearing assembly from the spindle.
5. Remove the automatic adjuster spring from the adjuster lever.
6. Rotate the automatic adjuster starwheel enough so both shoes move out far enough to be free of the wheel cylinder boots.
7. Disconnect the parking brake cable from the actuating lever. Disconnect parking brake cable one side at a time.
8. Remove the both lower brake shoe to anchor springs.
9. Remove the 2 brake shoe hold-down springs from the brake shoes.
10. Remove the brake shoes, upper shoe-to-shoe return spring, automatic adjuster and automatic adjuster lever from the backing plate as an assembly.
11. Separate the brake shoes from the automatic adjuster mechanism.
12. Remove the brake shoe automatic adjuster lever from the leading brake shoe. To install:
    
13. Thoroughly clean and dry the backing plate. To prepare the backing plate, lubricate the bosses, anchor pin and parking brake actuating lever pivot surface lightly with lithium based grease.
14. Remove, clean and dry all parts still on the old shoes. Lubricate the starwheel shaft threads with anti-seize lubricant.
15. Assemble both brake shoes, the top shoe to shoe return spring, automatic adjuster and automatic adjuster lever before mounting on vehicle. Make sure the ends of the automatic adjusters are positioned above the extruded pins in the webbing of the brake shoes prior to installation.
16. Install the brake shoe assembly onto the brake support plate and install the hold-down springs.
17. Install the lower anchor springs and reconnect the parking brake cable to the park brake lever of the trailing brake shoe.
18. Rotate the serrated adjuster nut to remove the free-play from the adjuster assembly.
19. Install the automatic adjuster lever spring on the lead brake shoe assembly and the automatic adjuster lever.
20. Install the rear hub and bearing assembly. Install washer and retainer nut and torque to 124 ft. lbs. (168 Nm).
21. Install the wave washer, nut retainer and a new cotter pin onto the spindle. Install dust cap.
22. Adjust brake shoes so not to interfere with brake drum installation. Install the rear brake drum. NOTE: After installing the brake drums, pump the brake pedal several times to partially adjust the brake shoes. To verify proper operation of the self-adjusting parking brake, be sure that both rear brakes are not dragging when the parking brake pedal is released.
    
23. Install the rear wheels and lug nuts. Torque the lug nuts, in a star pattern sequence, to 95 ft. lbs. (129 Nm).
24. Road test the vehicle. The automatic adjusters will continue brake adjustment during the road test of the vehicle.

How to Replace Brake Shoes
(DIY Complexity: Moderate / DIY Time: 3.2 hours)

Parts:
1. Brake Shoe Set

Tools:
1. Combination Wrench Set
2. Floor Jack
3. Jack Stand Set
4. Mallet Hammer
5. Brake Spring Tool
6. Flat Head Screwdriver
7. Needle Nose Pliers
8. Tire Iron
9. Brake Resetting Gauge

Supplies:
1. Brake Cleaner

Steps:
Step 1 * Secure your vehicle on a level surface, making sure your car will not roll or lean when jacked up.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

Step 2 * Break the lug nuts loose but do not remove. Lift up your vehicle using a floor jack.
o Tip: Using an aftermarket floor jack, instead of the original equipment (OE) jack, can make the job easier and safer. Verify the condition of the floor jack before use.

o Tip: Lug nuts fasten the wheel to the hub and may be on very tight. To gain more leverage, use a breaker bar to loosen the nuts.

Step 3 * Secure the vehicle with jack stands on both sides for safety before starting any work. Do not rely on the jack to hold the vehicle up while working.

Step 4 * Remove the lug nuts. Remove the wheels.
o Tip: Make sure the parking brake is released before removing the brake drum.

Step 5 * Remove the brake drum. If necessary, back off the star wheel adjuster.
o Tip: Hit the brake drum with a rubber mallet to break it loose from a rusted hub.

Step 6 * Clean the brake assembly using a“wet wipe method”. This method uses a spray bottle with water and detergent. Do not use compressed air to clean the brakes. Inspect the brake shoes for wear or damage.
o Tip: It is a good idea to leave one side assembled to use as a reference while you work on the other side.

Step 7 * Remove the primary and secondary brake shoe return springs from the anchor pin and brake shoes.
o Tip: The primary spring is connected to the front (primary) brake shoe and the secondary spring is connected to the rear (secondary) brake shoe.

Step 8 * Remove the adjuster cable and spring assembly. Remove the star adjusting screw and thread the adjuster all the way in.

Step 9 * Remove the front brake shoe retainer. Remove the front brake shoe and parking brake link.

Step 10 * Remove the parking brake lever from the rear brake shoe. Remove the rear brake shoe retainer and remove the rear brake shoe.
o Tip: Specialty brake tools are available to make brake shoe removal easier; but it is possible to remove the brake components with pliers.
o Tip: While you have the drum brake assembly apart, pry the outer seal away from the wheel cylinder and check for leaking brake fluid. If any brake fluid is leaking, replace or rebuild the wheel cylinder

Step 11 * Apply white lithium grease to the backing plate contact points.

Step 12 * Install the new brake shoes in the reverse order of removal. Be careful to keep the new brake shoes clean.

Step 13 * Inspect the brake drum and resurface or replace if necessary. Install the brake drum and adjust the brake shoes.
o Tip: There is a slot on the back of the backing plate usually blocked with a rubber grommet. To adjust the brakes, insert a screw driver into the slot and turn the star wheel adjuster. Spin the brake drum and stop adjusting when you feel a slight drag.

Step 14 * Install the wheels. Torque lug nuts to manufacturer’s specifications.

Step 15 * Lower vehicle and test drive to verify repairs.

Hope help with this (remember rated and comment this help).

Drum, Rear Brake System Standard Rear Brake

Item Part Number Description 1 2069 Brake Shoe Hold-Down Spring Pin 2 — Rear Wheel Cylinder Retaining Bolt (2 Req'd) 3 — Washer (2 Req'd) 4 — Anchor Pin (Part of 2211) 5 — Wheel Cylinder 6 2028 Brake Shoe Anchor Pin Guide Plate 7 2A637 Parking Brake Lever 8 2296 Brake Shoe Retracting Spring (Short) 9 2296 Brake Shoe Retracting Spring (Long) 10 2200 Rear Brake Shoe and Lining (Secondary) 11 — Washer 12 2106 Parking Brake Lever Pin Retainer 13 — Brake Shoe Adjusting Lever Cable Guide 14 2A642 Primary Brake Shoe Parking Brake Lever Link 15 2A601 Parking Brake Link Spring 16 2068 Brake Shoe Hold-Down Spring 17 2A176 Brake Shoe Adjusting Lever 18 2048 Brake Shoe Adjusting Screw Socket 19 2047 Brake Shoe Adjusting Screw Nut 20 2041 Brake Adjusting Screw 21 2049 Brake Shoe Adjusting Screw Spring 22 2200 Rear Brake Shoe and Lining (Primary) 23 2A178 Brake Shoe Adjusting Lever Cable 24 2211 Brake Backing Plate
Heavy Duty Rear Brake

Item Part Number Description 1 — Rear Wheel Cylinder Retaining Bolt 2 00538 Lock Nut 3 2212 Rear Brake Backing Plate 4 2262 Rear Wheel Cylinder 5 2A642 Primary Brake Shoe Parking Brake Lever Link 6 2A601 Parking Brake Link Spring 7 2A637 Parking Brake Lever 8 2106 Parking Brake Lever Pin Retainer 9 — Parking Brake Lever Bolt 10 — Secondary Shoe Assembly 11 2A179 Brake Shoe Adjusting Lever Cable Guide 12 2068 Brake Shoe Hold-Down Spring 13 — Adjusting Lever Pin 14 — Adjusting Lever Return Spring 15 2A176 Brake Shoe Adjusting Lever 16 2047 Brake Shoe Adjusting Screw Nut 17 2049 Brake Shoe Adjusting Screw Spring 18 2041 Brake Adjuster Screw 19 — Primary Shoe Assembly 20 2068 Brake Shoe Hold-Down Spring 21 2200 Rear Brake Shoe and Lining 22 2035 Brake Shoe Retracting Spring 23 2A178 Brake Shoe Adjusting Lever Cable 24 2092 Brake Adjusting Hole Cover 25 2069 Brake Shoe Hold-Down Spring Pin
The rear drum brakes:

• Have internal shoes that expand against the brake drum (1126).
• Are a single-anchor type.
• Are actuated by one rear wheel cylinder (2262).
• Have two pistons in the rear wheel cylinder (2261). One exerts force against the upper end of the primary shoe; the other exerts force against the upper end of the secondary shoe.
• Adjust rear brake shoes and linings (2200) automatically.
• Need manual brake adjustment if the adjusters are not operating properly or after the rear brake shoes and linings have been replaced.

When the brake pedal is applied, hydraulic fluid pressure forces the pistons in the rear wheel cylinder outward, moving the rear brake shoes and linings against the brake drum.
The rear drum brake system includes the parking brake mechanism. Refer to Section 206-05 .

i think your aware of how to change the brakes if im right and your problem is the rusted drum doesnt want to come off the only way to get the old drum off is to remove adjuster plug from behind drum dustshield and adjust the shoes so that there not even close to the braking area of the drum then try and wiggle the drum off of the assembly if it is not coming off then you need to use the old nylon hammer on the drum and i mean you must hit the drum from side to side trying by hand to wiggle the drum off its a tight fit and you need to strike the drum on the face not on the fins not wanting to damage with persistance and care and patience you will eventually be able to remove the drum to service brakes take care and good luck with it

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove the rear wheels.
3. Remove the drums.
4. Remove the automatic adjuster spring and lever.
5. Remove the hold-down clips and pins.
6. Rotate the automatic adjuster starwheel enough so both shoes move out far enough to be free of the wheel cylinder boots.
7. Disconnect the parking brake cable from the actuating lever.
8. Remove the lower shoe to shoe spring.
9. With the shoes held together by the upper shoe to shoe spring, remove them from the backing plate. Kelsey Hayes rear brake assembly (left side shown) Exploded view of the drum brake assembly—2004 model shown

GOODLUCK, shoes for this car ~ 15 bucks at auto zone.