Question about 1998 Cadillac Catera

1 Answer

WHERE IS THE CRANK SHAFT SENCER LOCATED ON THE MOTOR

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,489 Answers

The 2 crankshaft sensors are located on the front of the engine block, between cylinder Numbers 4 and 6. Crankshaft position A sensor is located on the upper crankcase and crankshaft position B sensor is located in the lower crankcase. Both sensors extend into the crankcase and are sealed into the engine block with O-rings. The crankshaft position sensors are not adjustable.

Posted on Jun 08, 2010

Ad

1 Suggested Answer

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crank case sencer


I have never heard of a crank case sensor. Do you mean crank shaft position sensor? If so, have a parts store show you their parts locator chart.

Apr 08, 2015 | Cars & Trucks

2 Answers

How do i time the cam sencer witrh the crank sencer ?


your question is realy garbled but I think you are asking about the timing of the cam and the crank sensors usually you have to have them both replaced at same time which means you can see the NO1 position on the cam and the position of the crank and thats with the cover off but I found out from another friend that if you go onto YouTube and request How To set timing on the Cam shaft and Crank shaft sensors you will get a video. MAKE SURE YOU SPELL IT ALL RIGHT OTHERWISE YOU WILL NOT FIND IT. Sorry about the Caps but wanted your attention use my spelling. Good Luck

Jul 22, 2014 | 1997 GMC Sierra

1 Answer

Wher can i find creank sencer cobalt 2008


most crank sensors are located @ crank shaft damper pulley, unless somebody moved it with out telling me.

Jan 15, 2013 | 2008 Chevrolet Cobalt

1 Answer

Cam shaft position sencer


howdie is that the code that came up?why are we changing this ?anyway its located in the front of the motor

Jul 25, 2012 | 2006 Chrysler PT Cruiser

1 Answer

Cam shaft position sensor 350z


The Cam Shaft Position is behind the motor on passenger side and has a green cap with 2 little wires going to it .with a 10 mm bolt to take out now what most people on here did not tell is that it was hard to take the green cap off the sencer first because the clip is on the bottom so you cant see it to take it off and if you just try to take a flat head screw driver to it you will bust your green clip.so take the sencer and cap off together and then take the green cap off after you get the sencer out .ok when you take the 10mm bolt out then you can reach down and pull the sencer out but its pretty hard just to pull out your going to want to twist it but you dont have to you are just pulling against the rubber O ring thats on the sencer just pull hard and it will come out.then pull the cap off .you acually push in on the clip towards the sencer to get it off ,not down ,but towards the bolt hole ,to take off,repalce clip put new sencer on and put sensor in motor,dont wiggle around on the wires to much because they are little and I could see braking one if not both

Mar 23, 2012 | 2004 Nissan 350Z

1 Answer

Ok i have a cam sencer problen have replace sencer and magnet it still cuts the car off and showes the same code


Try replacing the "Crank Shaft Position Sensor" this two sensors "Cam" and "Crank" communicate so if one is acting up it sends the wrong signal to the computer, I recently had the exact same problem but in reverse and a different vehicle, the other thing, although not very usual is the wire harnnes that connects to the sensor itself could not be working properly. Good Luck!

Sep 06, 2010 | 1989 Buick Riviera

2 Answers

I have a 1993 cutlass ciera s and it dies


my 93 olds stalls then dosent turn over but i take ecu fuse out and wait a few minutes it will start and run till next time it decides to stall

May 14, 2009 | 1993 Oldsmobile Cutlass Ciera

2 Answers

93 buick regal grand sport


no the crank shaft sensor would not stop it from turning over

Oct 17, 2017 | 1994 Buick LeSabre

Not finding what you are looking for?
1998 Cadillac Catera Logo

726 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...