Question about 1995 Honda Accord

1 Answer

I have a 95 honda accord check engine light flash 1 long and 7 short. what does that code mean?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 973 Answers

That means Code 17, one long flash means 1, seven short flashes means 7. The code is for the Vehicle Speed Sensor (VSS) Have it checked and replaced if necessary.

Posted on Jun 13, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1992 honda no spark


1 one spark plug or all 4? (key fact one missing)



insert honda OBD1 diagnostic jumper (or as FSM directs)

engage Diag mode.

then crank engine for 5 seconds.

then release key,

does the ECU flash out codes for a failure.,, BINGO

all cars work like this 1987 to now, USA>

what engine, of the many?







fsm quotes (and vast on line data same on all honda\'s)

there are more online facts on honda\'s than any car.

they race them and have hacked them to infinite levels.

now thequote



On 1990-95 Accord (except V-6) and 1992-95 Prelude, the codes are read from the check engine light after the two-wire service connector has been jumpered. On Accords, the service connector is under the dash on the passenger side. On Preludes, it is located behind the center console. Codes 1 through 9 are indicated by a series of short flashes; two-digit codes use a long flash for the first digit followed by the appropriate number of short flashes. For example, Code 14 would be indicated by 1 long flash followed by 4 short flashes. Codes are separated by a pause between displays. Multiple codes are transmitted in an alternating pattern. For example, a code 3 and 14 would be displayed as 3 short flashes (for Code 3) followed by the separator pause, then 1 long flash and 4 short flashes (for Code 14).



my comment, code 4 or 8 tells you , CKP or CMP sensors are dead.

in gringo that is "crank or cam sensors dead)

the ECU can report even , 1 in 10 pulses missing.

its very very , accurate in this report.

crank

release key

wait a minute to see if the ECU sets DTC errors.

do not turn off the key,or it erases them. wait, for 5min.

Jul 09, 2014 | 1991 Honda Accord

1 Answer

How to turn the rely back on to the fuel pump


as always check all fuses FIRST (electrics issues, EFI is that.)

the Puter magic is mindboggling, but..
why not post the symptoms, ????????
is it dead fuel pump or the more accurate, low or no fuel pressure?

All ECU/PCM (EFI ) all cut the pump for many reasons.
PCM is PGM-FI , in honda speak. PCM is modern term.
first really is fuse checks. !!!
1: no spark. (did you pull the CEL DTC blink codes to see if the ECU
is unhappy?
2: many cars (you must crank to run the pump) so looking not cranking for 12v at the pump , you fail and is normal.
(2 man rule one to crank, one to listen or check voltage at pump
or pump pressure at rail or filter) (a new filter is a good ploy now)

the fsm is here, and covers this, read the FSM
some pages are missing,,, so get real FSM
or go to alldata.com
http://www.scantool.net/software/alldata-diy-1-month-subscription.html

free but , some pages missing(good luck with free)

http://hondatech.info/downloads/Auto/Manuals/Accord/

see chapter 16, electrics.
F22A6 engine
this page is valid.
http://troubleshootmyvehicle.com/honda/2.2L-2.3L/how-to-test-the-fuel-pump-2

I like the (above) is cam dead?, line.... funny that.
(gather evidence, fuses good, cam spins (watch it) no DTC stored.
then check for spark no spark work spark now ,not fuel.
with a dead cam there is no CMP , no CMP the ECU pukes
codes for CMP Dead.
this is an interference engine so i'd bet that belt is fresh, huh?
ever 60k? per the opr; guide.

watch for codes, 4,8,9,15,16 (OBD2 DTC codes)
code 9 is dead cam. dead spark and all fuel is cut. for ever.
TDC&crank sensor, must work and not show DTC codes.

http://www.troublecodes.net/honda/hondadtc/

DTC flashing? The DLC jumper:
On 1990-95 Accord (except V-6) and 1992-95 Prelude, the codes are read from the check engine light after the two-wire service connector has been jumpered. On Accords, the service connector is under the dash on the passenger side. On Preludes, it is located behind the center console. Codes 1 through 9 are indicated by a series of short flashes; two-digit codes use a long flash for the first digit followed by the appropriate number of short flashes. For example, Code 14 would be indicated by 1 long flash followed by 4 short flashes. Codes are separated by a pause between displays. Multiple codes are transmitted in an alternating pattern. For example, a code 3 and 14 would be displayed as 3 short flashes (for Code 3) followed by the separator pause, then 1 long flash and 4 short flashes (for Code 14).

if fee for you , this very old car, so here is your long lost oper guide
http://justgivemethedamnmanual.com/honda/

Nov 27, 2013 | 1991 Honda Accord

1 Answer

HAVE NO SPARK OUT THE COIL


nov 6, how'd i miss this..???
not the V6 , right?
as always, check all fuses. (op guide in glove box shows em)
ok the car (USA) has a EFI system with spark too.
this EFI system has 3 parts to make spark. (not counting coil)
crank sensor (the ECU will flash a code if dead, did you looK).
ECU (unliikely but do check the DTCs lamp codes)
Dizzy
Coil.
Got code (DTC) 4,8,9,15, ah bingo?
here are the words in the FSM ( got one yet , they are free too)

On 1990-95 Accord (except V-6) and 1992-95 Prelude, the codes are read from the check engine light after the two-wire service connector has been jumpered. On Accords, the service connector is under the dash on the passenger side. On Preludes, it is located behind the center console. Codes 1 through 9 are indicated by a series of short flashes; two-digit codes use a long flash for the first digit followed by the appropriate number of short flashes. For example, Code 14 would be indicated by 1 long flash followed by 4 short flashes. Codes are separated by a pause between displays. Multiple codes are transmitted in an alternating pattern. For example, a code 3 and 14 would be displayed as 3 short flashes (for Code 3) followed by the separator pause, then 1 long flash and 4 short flashes (for Code 14).
end quotes



or RTM? here. free, its all there.... even simple coil tests.
but id bet its not the coil, for sure i dont know, i only tests. and then replace truly bad parts.
http://hondatech.info/downloads/Auto/Manuals/Accord/

Nov 06, 2013 | 1991 Honda Accord

2 Answers

Engin light stays on


The ECM has detected a fault in one or more of its systems. Go here,
extreme-check-engine-light-codes.com
and it will explain what to do to extract any codes that are stored.
Come back here with the code(s) and I can try and help further.

Oct 11, 2011 | 1993 Honda Accord

2 Answers

Check engine light on


1990-95 FOUR CYLINDER ACCORD AND 1992-95 PRELUDE
See Figures 7, 8, 9, 10, 11 and 12
On 1990-95 Accord (except V-6) and 1992-95 Prelude, the codes are read from the check engine light after the two-wire service connector has been jumpered. On Accords, the service connector is under the dash on the passenger side. On Preludes, it is located behind the center console. Codes 1 through 9 are indicated by a series of short flashes; two-digit codes use a long flash for the first digit followed by the appropriate number of short flashes. For example, Code 14 would be indicated by 1 long flash followed by 4 short flashes. Codes are separated by a pause between displays. Multiple codes are transmitted in an alternating pattern. For example, a code 3 and 14 would be displayed as 3 short flashes (for Code 3) followed by the separator pause, then 1 long flash and 4 short flashes (for Code 14).


0900c1528005f5b0.jpg

Fig. Fig. 7: Fault codes are read from the check engine light on most late-model vehicles


0900c1528005f5b1.jpg

Fig. Fig. 8: On Accords, the service connector is located under the dash on the passenger side


0900c1528005f5b2.jpg

Fig. Fig. 9: The service connector on Preludes is located behind the center console

  1. Use a jumper wire to connect the two terminals of the service connector together.
  2. Turn the ignition switch ON ; the check engine light will display any stored codes by rhythmic flashing.

In the event that a code is encountered which is not on the chart, re-count the number of flashes. If the code is truly wrong, it will be necessary to swap the ECU for a known-good unit and recheck. Since this can be expensive, you may wish to bring the car to a reputable repair facility if no other cause of the failure can be found. This may save you the expense of purchasing an unnecessary part.
  1. If no codes are displayed but a driveablity problem exits, testing of the system individual components is necessary to find the problem. If codes are displayed, follow the appropriate troubleshooting chart in this section.



0900c1528005f5b3.jpg

Fig. Fig. 10: Fault code chart for 1990-93 Accords

Jan 28, 2011 | 1990 Honda Accord

2 Answers

Need to find obd in 1990 honda accord


TROUBLE CODES System Diagnosis READING CODES When the "Check Engine'' warning light on the dashboard comes on and stays on, it indicates a problem in the fuel injection/emissions system. Check the ECU for fault codes. On certain models, some codes will not trigger the check engine light; if driveability has suffered, check for stored fault codes. The most common error when using fault codes is to assume the indicated component has failed rather than checking the entire circuit. The presence of a trouble code means simply that the electrical circuit for the named component is not functioning properly. For example, a code for the oxygen sensor circuit does not automatically mean the oxygen sensor has failed. A wire terminal may simply be loose or corroded at the connector. When using diagnostic or fault codes, always remember that the entire circuit including the component must be checked carefully. On 1990-95 Accord (except V-6) and 1992-95 Prelude, the codes are read from the check engine light after the two-wire service connector has been jumpered. On Accords, the service connector is under the dash on the passenger side. On Preludes, it is located behind the center console. Codes 1 through 9 are indicated by a series of short flashes; two-digit codes use a long flash for the first digit followed by the appropriate number of short flashes. For example, Code 14 would be indicated by 1 long flash followed by 4 short flashes. Codes are separated by a pause between displays. Multiple codes are transmitted in an alternating pattern. For example, a code 3 and 14 would be displayed as 3 short flashes (for Code 3) followed by the separator pause, then 1 long flash and 4 short flashes (for Code 14). Fig. 7: Fault codes are read from the check engine light on most late-model vehicles 86804048.gif
Fig. 8: On Accords, the service connector is located under the dash on the passenger side 86804049.gif
Fig. 9: The service connector on Preludes is located behind the center console 86804050.gif
  1. Use a jumper wire to connect the two terminals of the service connector together.
  2. Turn the ignition switch ON; the check engine light will display any stored codes by rhythmic flashing. NOTE: In the event that a code is encountered which is not on the chart, re-count the number of flashes. If the code is truly wrong, it will be necessary to swap the ECU for a known-good unit and recheck. Since this can be expensive, you may wish to bring the car to a reputable repair facility if no other cause of the failure can be found. This may save you the expense of purchasing an unnecessary part.
  3. If no codes are displayed but a driveablity problem exits, testing of the system individual components is necessary to find the problem. If codes are displayed, follow the appropriate troubleshooting chart in this section. Fig. 10: Fault code chart for 1990-93 Accords 86804051.gif
    Fig. 11: Fault code chart for 1994-95 Accords (four cylinder) 86804052.gif
    Fig. 12: Fault code chart for 1992-95 Preludes 86804053.gif

Dec 14, 2010 | 1990 Honda Accord

1 Answer

I have a 1992 honda accord that turns off when the check engine turns on


Well you need to pull codes first under the glove compartment their is a connector with 2 wires connect with a jumper wire turn key to on position dont start motor. count the check engine lights. long flashes are 1 short flashes are 2 position so lets say 2 long flashes and 4 short flashes code24 check a manaul or call auto zone for free then go from there

Nov 12, 2009 | 1988 Honda Accord 4 Door

8 Answers

D4 blinking, spedometer not working, check engine light on


Hi, a few questions 1st. Did your mechanic check for engine codes? Is your Honda a v-6 or 4 cylinder?
The flashing D4 light indicates a possible transmission malfunction. You should avoid rapid acceleration until the cause of the light blinking is determined.
If you have the V-6, there is a diagnostic port to connect a scan tool to read any stored engine codes that have turned on the check engine light. This port is located behind the ashtray in the center console (most cars did not have this til 96).
If you have the 4 cyl engine, there is a service connector located under the dash on the pass. side. Inside the connector is what looks like a 2 wire plug should be attached. Take a paper clip, unbend it, and insert the 2 ends of the clip into the connector to 'jump' it. Turn the ignition switch to the on position (don't start the vehicle), and the check engine light will flash. Count the flashes, short flashes are for code #'s 1 to 9 (single digit code), a 2 digit code will be a long flash for the 1st digit, followed by a short flash for the 2nd digit. If there is more than one code, they will be separated by a pause. They will repeat so you can count them and write them down. Let me know what the code #'s are so I can help further. Curt

Jul 22, 2009 | 1995 Honda Accord

1 Answer

Check engine light


try codes 41 and code 7

May 26, 2009 | 1992 Honda Accord

1 Answer

92 Honda Accord LX 2.2 liter d4 flashing 1 long 3 short acts like over drive going on and off or switching back and forth between d3 and d4 when in d4 dealer could'nt get any codes from when they...


on my 95 accord my d4 light used to flash after driving for for an hour or 2 then the speedo would do strange things.so i changed the speed sensor relay [located on the gearbox] and solved the problem.

Aug 09, 2008 | 1995 Honda Accord

Not finding what you are looking for?
1995 Honda Accord Logo

Related Topics:

677 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Marvin
Marvin

Level 3 Expert

85219 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...