Question about 2001 Ford F250 Super Duty Super Cab

1 Answer

Fuel pump relay location 2001 f250 5.4L Replaced fuel pump and inline filter and hit the key still had no fuel pressure....installed pressure guage on rail and had no pressure at koeo or while cranking and after about 10 or 15 tries the pressure slowly came up and engine ran. I doubt that the problem resolved itself and will happen again...I suspect the relay but can't find it in the owners manual and Ford was completely useless..wouldn't tell me...help.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,874 Answers

The Fuel Pump Relay is under the hood in the Fuse Box / Relay Plate:

fuel pump relay location - e9cb4c0.jpg

Posted on Jun 14, 2010

Ad

1 Suggested Answer

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Got a 99 chevy silverado 4.8 litre.codes are lean bank 1 and 2 put fuel pressure guage on and reading 20 ilbs pressure jumps to 41 ilbs . then drops back to 20 ilbs could it be the fuel pump?


My info says fuel pressure 55--62 psi. Yes, probably the fuel pump. Usually low pressure is a problem on the supply side. You can be thorough, check proper voltage and ground at fuel pump connector. Check inline fuel filter. I've checked inline fuel filters before where the fluid that ran out looked like dirty water. Don't take connections loose from inline fuel filter unless your sure, no pressure on the system.
You could block the return line, where applicable, momentarily, to see if pressure will go high. If not, it should be the pump.

Dec 15, 2016 | Cars & Trucks

1 Answer

Replaced the Fuel Delevery System/Pump and the in-line fuel filter on my 93 GMC Vandura Van 2500. Van turnes over; however, no fuel in getting to the engine. I have checked the Fuel Pump...


install a fuel pump guage and check pressure at key on and start, it should hardly vary, it the pressure is constant check the injector signal with a noid light, while you are at it check spark(no spark no injector signal) you won't find a relay fuse

May 07, 2011 | GMC Vandura Cars & Trucks

1 Answer

While truck was running I disconnected a fuel relay to relieve pressure from fuel lines to change the fuel filter. Truck would not restart. Assumed fuel pump was bad . Replaced it along with in-tank filter...


Removing the relay would not releive the fuel pressure. Arc across the fuel relay terminals and jump start the fuel pump. Also check to make sure the fuel filter is properly installed.

Jan 07, 2011 | 2001 Ford Expedition

1 Answer

My fuel pressure is not holding how do i know if it's my fuel pressure regulator or fuel pump


MEASURE FUEL PUMP PRESSURE AT FUEL FILTER CONNECTOR. ATTACH PRESSURE GUAGE TO FITTING COMING FROM TANK. MAKE SURE THER ARE NO LEAKS FIRST THEN HAVE SOMEONT TURN THE IGNITION ON CK. GUAGE PRESSURE TURN KEY OFF PRESSURE SHOULD REMAIN CONSTANT SINCE PUMP IS DEAD HEADED ( NO RELIEF/ REGULATOR) IF PRESSURE FALLS ,PUMP INNER CK VALVE IS LEAKING. IF PRESSURE DOES NOT FALL THEN SUSPECT REGULATOR

Aug 06, 2010 | 2001 Pontiac Firebird

4 Answers

Im working on a 95 s10 blazer.It has the 4.3 engine.It will only start if it is sprayed with starting fluid.the fuel pump,fuel filter,and pressure regulator have all been replaced.Seems like the system...


It sounds like the fuel pump is not working. Perhaps the install was not completed correctly. Things to check, fuel pump relay, wiring, voltage to the pump.
The priming happens as soon as you put the key in and turn it to "acc" (you may hear a humming sound). Then once you turn it to "start" the injectors and spark plugs start firing.
Another possibility is that the fuel filter was installed backwards.

Apr 22, 2010 | 1995 Chevrolet S-10 CA Edition

1 Answer

2000 Jeep Grand cherokee Laredo wont start. Engine turn over . No noise from fuel pump with ignition on. Replaced fuel pump and filter.Turn ignition on- pump did not run.Jumped the fuel pump at the pump...


sounds alot the the pcm it controls the fuel pump and ign system but the anti theft would keep it from starting because the key has a transponder in it programmed for that vehicle and that would kill all ign if triggered

Sep 22, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Locate fuel filter, and safety switch to fuel pump


The filter is located at the rear seat, you have to remove it first, then you will see a cap attach with some screws. Inside that cap you`ll find the fuel filter. Before you change the fuel filter you have to release the fuel pressure first. To do that, first find the FUEL PUMP RELAY in the main fuse box located in the engine. Once you located open the fuel door and take off the cap and leave it open. Start the engine, take off the FUEL PUMP RELAY and leave the engine stop itself, when this occurs turn off the key, the you can take off the filter and changed it

Apr 21, 2009 | 2001 Hyundai Elantra

2 Answers

95 blazer with vortec spark is fine fuel is not


you have to put a guage on it to find out the pressure it may kick on but not enough pressure

Apr 17, 2009 | 1995 Chevrolet Blazer

1 Answer

Daewoo Lanos, turns over but will not start.......


You must check for power and ground to the fuel pump ,you will have power for approx. 2 seconds with key first turned to the run position and then you will have constant battery voltage during cranking. You may also want to go to AutoZone .com or Alldata.com and bur online manuel for you Daewoo.the are very reasonable and informative. If you find you have correct voltage supply and ground, and assuming the fuel guage is correct and there is fuel,it is very likely you will be replacing the fuel pump , strainer and filter. Don`t laugh on the fuel guage comment, I have had several vehicle towed in to me for no starts, only to find the guage not reading correctly , and the vehilcle was out of fuel.Good luck I hope this helps.
Brett

Jan 14, 2009 | 2002 Daewoo Lanos

1 Answer

Wont start


Where the car runs on starter cleaner, this is definitely a fuel problem...

Could be a few things:

Do you hear the fuel pump running outside the car (for a few seconds) when you turn the key on (engine off)?

If not it might be the pump or the pump relay (in the engine compartment fuse and relay box)

If so, it might be:
Clogged inline fuel filter (in the fuel line from the pump to the engine)
Bad fuel pressure regulator
Bad injectors/wiring

Did you check the fuse and wires to see if you have power (and a good ground) to your engine computer (controls fuel injectors), this could also be the culprit (without power to the computer there is no way for the engine to get fuel).

Aug 27, 2008 | 2001 Oldsmobile Alero

Not finding what you are looking for?
2001 Ford F250 Super Duty Super Cab Logo

8,148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...