1998 Chevrolet S-10 Pickup Logo

Related Topics:

A
Anonymous Posted on Jan 15, 2018

Chevy camaro v6 will a bad oil sending unit cause the car to not idle right and drive? the car will start on when u first try but after it dies it wont start again sounds like it is misfiring and will actually backfire under the hood when u rev the engine. Got a low oil light and the car has oil in it

1 Answer

Roger Paull III

Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Dedicated:

Visited the website for 20 consecutive days.

  • Expert 318 Answers
  • Posted on Oct 12, 2018
 Roger Paull III
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Dedicated:

Visited the website for 20 consecutive days.

Joined: Sep 15, 2009
Answers
318
Questions
0
Helped
118408
Points
785

Could be a bad oil pump, i wouldn't start it again without having an aftermarket oil pressure gauge hooked up to make sure it's getting oil.

5 Related Answers

gmiller442

  • 17 Answers
  • Posted on Jan 22, 2009

SOURCE: 1989 Chevy K2500 - idles fine but stalls out when put into drive.

Sounds like the injectors may be bad or just really dirty. You say that the truck is only used as a plow truck, so I would assume that it sits alot. If you dont add any fuel stabilizer to the tank, the fuel will start to degrade and the will gum up your injectors. One thing you can do is to pull the air cleaner assembly off and look at the injectors while the truck is running. Look at the bottom of the injectors while it is running. The injectors shouldbe spraying fuel with a fan spray of fine mist. If you see any drips of fuel in the this fine mist, that injector is at least dirty or on its way out. I would recommend that you change your fuel filter and then get some fresh fuel and the purchase some Seafoam fuel injector cleaner from your local parts store. Dont mess around with anything else. GET SEAFOAM. If it is in a plastic bottle it is not strong enough to do anything. Seafoam is in a metal can. Dump the seafoam in and run the truck as much as you can. This will help clean out the injectors.

Ad
dennymulford

Dennis Mulford

  • 1055 Answers
  • Posted on Mar 30, 2009

SOURCE: 1988 chevy pickup 4.3 V6 that has constant backfire

bad dis cap or rotor maby a bad plug wire or valve sticking or out of adjusment

Anonymous

  • 491 Answers
  • Posted on Sep 01, 2009

SOURCE: What is the distributor timing mark for 89 chevy

Is the vacuum hose removed from the dist when the timing is being checked?
Are you connected to the first plug wire (closest to the rad) on the drivers side?
If this is being done.....remove the cap and rotor and check the springs on the mechanical advance,the advance should be tight to the shaft and springs tight.
I would set the base timing on this set up .....at idle speed...... at between 5 and 10 before TDC.

Remember......timing marks on modified engines are not always accurate. Parts from this year and that year put together.

Anonymous

  • 986 Answers
  • Posted on Nov 10, 2009

SOURCE: 85 2.8 camaro timing specs

chain

Anonymous

  • 26 Answers
  • Posted on Nov 23, 2009

SOURCE: i have a 2001 chevy camaro v6 3800 i here a

check you idler and tensioner pully also water pump could be going bad

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

1994 Chevy Camaro, 6 Cylinder, stalling problem

Try cleaning the throttle body and the idle speed control valve, they get full of sludge and this causes stalling. Use a product called CRC Throttle valve cleaner on both parts, DO NOT USE CARB CLEANER IT WILL RUIN THE PARTS.
1helpful
2answers

What is the sending unit and were is it located on my Chevy camaro 3.8 v6 1998

you will have several sending units.
1. Oil pressure sending unit, which according to peoples site that I have visited is right above the oil filter.
2.sending unit in gas tank going to gauges, which is in the gas tank.
3. temperature sending unit, which is located near the thermostat housing or near the end of the upper radiator hose.
0helpful
1answer

Timing chain

you have probably knocked somewires loose like cam sensor or crank sensor re check all your wiring near where you did all the work..
0helpful
1answer
2helpful
2answers

1989 VW cabriolet oil pressure warning light on at low rpm and idle. Oil pressure gauge shows sub 1 bar at same time. Is this a sending unit problem, or an oil pump problem? Where are sending units? ...

The Oil light is a dreaded sight, especially at idle. Usually if an oil pump fails, it dies, the same with an oil pressure sender. I had the same problem with a 97 neon, at idle the oil light comes on... (192,000 miles). If the oil used at the oil change was a thinner viscosity than what was in there, that could cause it. If not, it could be bearings going bad on the motor creating a low pressure situation. I fixed it by going to a thicker viscosity, from 5w-30 to 10w-30, and in a week the light went off... this was 7 months ago. Just food for thought, hope this helps.
2helpful
1answer

I have a 96 camaro 3.8 v6. The car will start and run fine but when i come to a stop it will not idle and dies. Does anyone have any idea?

sounds like the injectors are dirty could be a bad idle sensor also, try a can o 'seafoam' at auto parts store. no injector clenor either just seafoam
Not finding what you are looking for?

233 views

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

john h

Level 3 Expert

29492 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...