For 1996 Chevrolet Cavalier 2.2L
SFI OHV 4cyl
the check the next Head Bolt Torque sequence...
------------
front | 8 4 1 5 9 |
of | |
engine | 7 3 2 6 10 |
------------
Step 1: torque long bolts 8,4,1,5, & 9 to 46 Ft/Lbs
torque short bolts 7,3,2,6, & 10 to 43 Ft/Lbs
Step 2: torque all bolts an additional 90 degrees
Recheck final torque in sequence
*** CAUTION ***
engine uses Torque To Yield head bolts (TTY) that
permanently stretch during the initial installation.
New head bolts must be used when cylinder head is
replaced or re-installed to obtain proper torque.
Hope helps (remnember rated this).
SOURCE: Looking for the torque specs for 1998 chevy astro van?
1998 chevy astro 4.3 v6 torque specs include :
* foot pounds *
balance shaft (if equiped) gear bolt = step 1 = 15 ft.lbs. step2 = additional 35 degrees.
camshaft sprocket bolt = 18 ft. lbs.
connecting rod cap = step 1 = 20 ft. lbs. step 2 = additional 70 degrees.
crankshaft damper bolt = 74 ft. lbs.
crankshaft oil deflectorbolt/nut = 27 ft.lbs.
cylinder head bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees. (tighten in sequence)
exhaust manifold bolts = step 1 = 11 ft. lbs. step 2 = 22 ft. lbs.
flywheel bolt = 74 ft. lbs.
main bearing cap bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees.
oil filter adapter bolt = 15 ft. lbs.
oil pan bolt/nut = 18 ft. lbs.
oil pump bolt = 66 ft. lbs.
rocker arm with press in studs = 18 ft. lbs.
rocker arm with screw in studs = 19 ft. lbs.
valve lifter retainer bolt = 12 ft. lbs.
water pump bolt = 33 ft. lbs.
* inch pounds *
balance shaft retaining plate bolt = 106 in. lbs.
camshaft retainer plate bolt = 106 in. lbs.
front cover bolt = 106 in. lbs.
intake manifold upper = step 1 = 44 in. lbs. step 2 = 88 in. lbs.
intake manifold lower = step 1 = 27 in. lbs. step 2 = 106 in. lbs. step 3 = 133 in. lbs. ** (tighten bolts in sequence)
thanks for your vote !
SOURCE: chevy cavalier need torque specs for 4cylinder heads
What torque specs and what engine/trans combo?
SOURCE: torque specs for 2000 chevy silverado truck 4.3 v-6 engine
Not sure what torque spec's your looking for.
Go to www.AutoZone.com, enter your vehicle information and check specifications. You should be able to look up the torque spec's your looking for.
Good luck.
Regards,
SOURCE: TORQUE SPECS /HEAD GASKET/2001 CAVALIER...
for the 2.2L OHV:
(pully 8 4 1 5 9 <-- long bolts @ 63Nm (46ft/lb)
side ) 7 3 2 6 10 <-- short bolts / 10 is the stud @ 58Nm (43ft/lb)
for the 2.4l
dohc are as follows:
(pully 9 3 1 5 7
side) 10 6 2
4 8
bolts 1-8 torqued to 65Nm (40ft/lb)
bolts 9-10 torqued to
40Nm (30ft/lb)
then (either engine) give each an additional 90° (¼)
turn
it's best to do
the tightening in stages, you don't want to go completely tight on the
first pass or there will problems and you'll get to do it all over again
6,136 views
Usually answered in minutes!
×