1998 FORD FESTIVA HEAD BOLT TORQUE SETTINGS & TIGHTENING SEQUENCE (1.5 LITRE ENGINE)

The torque sequence and specifications for the cylinder head bolts on a 1998 Ford Ranger 2.5L gasoline engine are as follows:

1. Tighten all bolts in the sequence shown below to 22 ft-lbs (30 Nm).8 4 1 5 \ ' / ' / 7 3 2 6
2. Tighten all bolts in the same sequence to 45 ft-lbs (61 Nm).
3. Tighten all bolts in the same sequence an additional 90 degrees (1/4 turn).
4. Tighten all bolts in the same sequence an additional 90 degrees (1/4 turn) again.

Ensure that you follow the sequence and torque values precisely to prevent uneven tightening and potential head gasket issues. It's also crucial to use a good quality torque wrench for accuracy. Please note that torque specifications may vary slightly depending on the specific engine build, so it's always a good idea to consult your vehicle's service manual for the most accurate information for your particular engine.

Question edited for clarity.
Question moved to model category.

All here for the three engine types

https://www.autozone.com/diy/repair-guides/nissan-frontier-xterra-1998-05-torque-specifications-repair-guide-p-0996b43f8037fa5c

https://www.google.com/search?q=2004+Nissan+Xterra.+cylinder+head+bolt+sequence+and+torque+specs

..

1998 Isuzu Truck Rodeo 2WD 2.2L MFI DOHC 4cyl

The Head Bolt Torque

Torque sequence ----------------- front ' 7 3 1 5 9 ' of ' ' engine ' 8 4 2 6 10 ' ----------------- Step 1: torque bolts in sequence to 18 Ft/Lbs Step 2: turn bolts in sequence an additional 90-degrees Step 3: turn bolts in sequence an additional 90-degrees Step 4: turn bolts in sequence an additional 90-degrees recheck final torque in sequence

1998 Isuzu Truck Rodeo 2WD 3.2L MFI DOHC 6cyl

The Head Bolt Torque

Torque sequence -------------- front ' 6 1 3 7 ' of ' ' engine ' 5 2 4 8 ' -------------- Step 1: torque to 20 Ft/Lbs Step 2: torque to 47 Ft/Lbs recheck final torque in sequence

Hi there:



Fig. Cylinder head bolt loosening sequence - Altima & Maxima 3.5L engine

Install the cylinder head bolts and torque in sequence as follows:

1. Step 1: 72 ft. lbs. (98 Nm).
   
2. Step 2: Completely loosen all bolts.
   
3. Step 3: 26-32 ft. lbs. (34-44 Nm).
   
4. Step 4: plus 90-95 degrees clockwise.
   
5. Step 5: plus 90-95 degrees clockwise.

Fig. Right cylinder head bolt torque sequence- Altima & Maxima 3.5L engine




Fig. Left cylinder head bolt torque sequence- Altima & Maxima 3.5L engine

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day

hope this helps,

Torque sequence --------- front ' 6 1 3 7 ' of ' ' engine ' 8 4 2 5 ' --------- Step 1: torque bolts in sequence to 37 Ft/Lbs Step 2: torque all bolts in sequence an additional 120 degrees Step 3: torque bolts 1,2,3, & 4 an additional 30 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.
always torque from center
Tighten each bolt an additional 90° in sequence.

Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.

Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.

B2500 4 Cylinder

Torque sequence: --------- ' 10 6 2 4 8 ' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51 Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final tighten all bolts an additional 90 to 100 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.

B3000 3.0 6 Cylinder

Torque sequence ---------- ' 6 4 2 8 ' ' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque to 73 Ft/Lbs

B4000 4.0 6 Cylinder

Torque sequence --------- ' 5 1 3 7 ' ' ' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs Step 3: turn cylinder head bolts in sequence an additional 90-degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.

Good luck with this job!

heres the torque specs and the way to tighten the head bolts for your 1998 toyota sienna, hope this helps,
12 point bolts step 1- 40 ft lbs
step 2- additional 90 degrees
recessed bolt 13 ftlbs

Cylinder Head Bolts

Step 1
Head Bolts A 46 (62)
Head Bolts B 43 (58)

Step 2 Additional 90 Degrees

Tightening Sequence:
http://www.anubiscycle.com/fixya/99cavheadsquence.png

you tighten in sequence.first pass you torque bolts 35 -40 ft lbs.second pass is. 56 - 60 ft lbs.