Roof not operating from switch in dash. Operating with key manualy. Could the switch in the dash be checked somehow? Any answer is appreciated

The roof opening panel is an electronically operated panel that can be opened or closed by the roof opening panel switch. Actuating the switch in either a forward or rearward motion supplies a ground to the roof opening panel motor. The vent and soft-stop functions are controlled by the roof opening panel motor. These positions are obtained when an internal motor cam opens the roof position switch, removing the ground from the switch. The roof opening panel has an express open feature activated when the switch is pressed momentarily. The roof opening panel is closed by continuous activation of the switch until the sunroof stops movement. This function is controlled by the roof opening panel motor.

Visual Inspection Chart Mechanical Electrical

• Roof opening panel
• Opening shield
• Roof panel frame
• Opening shield guide feet

• Central junction box (CJB) fuses:
  • 2 (20A)
  • 29 (5A)
• Battery junction box (BJB) fuse 1 (60A)
• Accessory delay relay
• Roof opening panel control switch
• Circuitry
• Roof opening panel motor

• The roof opening panel does not open or close

• Central junction box (CJB) fuse:
  • 2 (20A).
  • 29 (5A).
• Battery junction box (BJB) fuse 1 (60A).
• Circuitry.
• Roof opening panel control switch.
• Roof opening panel motor.

• Go To Pinpoint Test E .

Do the power windows and power locks work ?

E6 CHECK VOLTAGE TO THE ROOF OPENING PANEL MOTOR - CIRCUITS 400 (LB/BK) AND 1173 (BN/OG)

• Key in OFF position.
• Disconnect: Roof Opening Panel Motor C920.
• Key in ON position.
• NOTE: Activate accessory delay relay for this check.
• Measure the voltage between roof opening panel motor C920-4, circuit 400 (LB/BK), and ground; and between roof opening panel motor C920-7, circuit 1173 (BN/OG), and ground.
• Are the voltages greater than 10 volts?

Yes
GO to E7 .

No
REPAIR circuit 400 (LB/BK) or circuit 1173 (BN/OG). TEST the system for normal operation. If you can't do electrical testing , there is a manual way to close it .
Roof Opening Panel Manual Operation

1. Remove the overhead console. For additional information, refer to Overhead Console in this section.

1. Insert a hex-head screwdriver in the center of the manual drive slot to depress the release pin. Rotate the screwdriver clockwise until the roof opening panel is closed.

The roof opening panel assembly uses an integrated motor and module to operate the roof opening panel. The roof opening panel motor and module are installed new as an assembly. The roof opening panel is an electronically operated glass panel that can be opened or closed by the roof opening panel switch. Actuating the switch in either a forward or rearward motion supplies a ground to the roof opening panel motor/module. The soft-stop function is controlled by the roof opening panel motor/module. The roof opening panel has 3 modes of operation, manual mode, express open and tilt. The express open feature is activated when the switch is pressed momentarily. The tilt feature is activated when the tilt switch is depressed. These functions are controlled by the roof opening panel motor/module.
Visual Inspection Chart Mechanical Electrical

• Roof opening panel
• Roof opening panel frame
• Roof opening panel drain hoses
• Roof opening panel lifter assemblies
• Roof opening panel water trough
• Roof opening panel rear trough guides
• Roof opening panel air deflector assembly
• Roof opening panel seal
• Roof opening panel shield

• Smart junction box (SJB) circuit breaker 47 (30A)
• Circuitry
• Accessory delay relay
• Roof opening panel switch

• The roof opening panel does not open or close - one direction only

• Circuitry
• Roof opening panel switch
• Roof opening panel motor assembly

• Go To Pinpoint Test E .

PINPOINT TEST E: THE ROOF OPENING PANEL DOES NOT OPEN OR CLOSE Test Step Result / Action to Take E1 CHECK THE ROOF OPENING PANEL LIFTER ASSEMBLIES FOR OBSTRUCTIONS OR DAMAGE

• Check the roof opening panel lifter assemblies for obstructions and damage.
• Are the roof opening panel lifter assemblies OK?

Yes
GO to E2 .

No
REMOVE all obstructions and REPAIR any damage. If lifter assemblies cannot be repaired, INSTALL a new roof opening panel frame. REFER to Roof Opening Panel Frame in this section. TEST the system for normal operation. E2 CHECK THE ROOF OPENING PANEL WATER TROUGH AND REAR TROUGH GUIDES

• Check the water roof opening panel water trough and rear trough guides for any loose obstructions.
• Are the roof opening panel water trough and rear trough guides installed securely and free from obstructions?

Yes
GO to E3 .

No
REMOVE all obstructions from the roof opening panel water trough and install securely. SECURE the rear trough guides or INSTALL new roof opening panel rear trough guides if damaged. REFER to Roof Opening Panel Rear Trough Guide in this section. TEST the system for normal operation. E3 VERIFY THE ROOF OPENING PANEL ADJUSTMENT

• Verify the roof opening panel is adjusted correctly.
• Is the roof opening panel adjusted correctly?

Yes
GO to E4 .

No
ADJUST the roof opening panel. REFER to Roof Opening Panel Alignment - Horizontal Adjustment and Roof Opening Panel Alignment - Height Adjustment in this section. TEST the system for normal operation. E4 CHECK THE ROOF OPENING PANEL MOTOR/MODULE FOR INITIALIZATION

NOTE: The roof opening panel motor initialization procedure must be done when repairs are carried out on any part of the roof opening panel assembly, including whenever the roof opening panel motor/module has been removed from the roof opening panel assembly, a new roof opening panel motor/module has been installed or when a new roof opening panel assembly has been installed. Refer to Roof Opening Panel Motor Initialization in this section.
• Carry out the Roof Opening Panel Motor Initialization procedure. Refer to Roof Opening Panel Motor Initialization in this section.
• If the concern still present?

Yes
GO to E5 .

No
The system is operating correctly. The roof opening panel motor/module was uninitialized. E5 CHECK THE POWER WINDOWS

• Key in ON position.
• Verify the power windows operate.
• Do the power windows operate?

Yes
GO to E6 .

No
REFER to Section 501-11 to diagnose the accessory delay relay circuit. E6 CHECK THE ROOF OPENING PANEL SWITCH

• Carry out the roof opening panel switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
• Did the roof opening panel switch pass the component test?

Yes
GO to E7 .

No
INSTALL a new roof opening panel switch. TEST the system for normal operation. E7 CHECK CIRCUIT CBP47 (GN/BU) FOR VOLTAGE

• Key in OFF position.
• Disconnect: Roof Opening Panel Motor/Module C922.
• Key in ON position.
• Measure the voltage between roof opening panel motor/module C922-4, circuit CBP47 (GN/BU), harness side and ground.
  
• Is the voltage greater than 9 volts but less than 16 volts?

Yes
GO to E8 .

No
VERIFY the smart junction box (SJB) circuit breaker 47 (30A) is OK. If OK, REPAIR the circuit. TEST the system for normal operation. E8 CHECK CIRCUIT GD143 (BK/VT) FOR AN OPEN

• Key in OFF position.
• Measure the resistance between roof opening panel motor/module C922-3, circuit GD143 (BK/VT), harness side and ground.
  
• Is the resistance less than 5 ohms?

Yes
GO to E9 .

No
REPAIR the circuit. TEST the system for normal operation. E9 CHECK CIRCUITS CPR37 (YE/GY), CPR39 (VT/WH) AND CPR40 (YE/OG) FOR AN OPEN

• Disconnect: Roof Opening Panel Switch C930.
• Measure the resistance between the roof opening panel motor/module C922-1, circuit CPR40 (YE/OG), harness side and roof opening panel switch C930-8, circuit CPR40 (YE/OG), harness side. Measure the resistance between roof opening panel motor/module C922-2, circuit CPR39 (VT/WH), harness side and roof opening panel switch C930-11, circuit CPR39 (VT/WH), harness side. Measure the resistance between roof opening panel motor/module C922-5, circuit CPR37 (YE/GY), harness side and roof opening panel switch C930-14, circuit CPR37 (YE/GY), harness side.
  
• Are the resistances less than 5 ohms?

Yes
GO to E10 .

No
REPAIR the circuit. TEST the system for normal operation. E10 CHECK FOR CORRECT ROOF OPENING PANEL MOTOR/MODULE OPERATION

• Disconnect the roof opening panel motor/module connectors.
• Check for:
  • corrosion.
  • pushed-out pins.
• Connect all roof opening panel motor/module connectors and make sure they seat correctly.
• Operate the system and verify that the concern is still present.
• Is the concern still present?

Yes
CHECK the jumper harness between the vehicle harness and the roof opening panel for open or shorted circuits. If the jumper harness is not OK, INSTALL a new jumper harness between the vehicle harness to the roof opening panel motor/module. Otherwise, INSTALL a new roof opening panel module/motor. REFER to Roof Opening Panel Motor in this section. TEST the system for normal operation.

No
The system is operating correctly at this time. Concern may have been caused by a loose or corroded connector. TEST the system for normal operation.

have you checked the fuse for the sunroof motor fuse bo lower dash drivers side cover/lid should give list , the owners manual should tell you how to manually close roof if fuse is ok ,have included a link to a hyundai forum as these sites have lots of advice and info
Hyundai Forums Hyundai Forum

Look in owners manual,it will show you how to raise/lower roof with tool end of dash driver side
Once you have the tool the best way to reset roof is to manualy lower it and lock rear cover
Two people helps to lower as you have to lift front of roof and lift rear
When rear metal cover is unlocked push roof fully down and lock cover
The roof should then work with the switch

I think it's in the boot on A4's?

Could it have bee disturbed somehow (loading stuff into boot?) or got wet/damp?

Other things to look for are corrosion to wiring leading into the central locking ECU, which (depending on which A4 it is) could be in the NSF footwell behind the carpets and plastic trim panels. Some A4's are bad for "dry" soldered joints in the loom leading up to the module.

When you manualy operate the OSF door and get in, does the interior light come on and does the "Door open" dash information module still function corrently?

your can check is it something stuck in the lock, first operate your roof either way, if you are going to open the roof as a first action boot lid will open to backward, let boot lid fully open and stop operating the roof, ignition off and have a look if something stuck you can see, if you are going to close the roof let close the roof and before close the boot lid stop operating roof switch, otherwise faulty boot lid lock, if faulty lock but you can try by mettle key blade which is in your electronic key, first take out mettle key from electronic key then insert mettle key in to the key hole in boot lid turn fully left and open boot if not work turn fully left and push it in, is this information helped you?

7 blinks (roof lock switch,not operated by user)
9 blinks (rear window switch not operated by user)
These codes mean user has not undone roof locks or rear window is not fully closed
Providing that is not your problem,reset roof control unit
Turn ignition off
In under bonnet fuse box remove fuse 32 7.5 amp for 20 seconds
Refit fuse and check roof operation
This clears codes and resets roof

The dash switch can affect the operation of the rear key switch. 1st thing to do is replace the dash switch and that will prob fix it all.

With the key on, your foot on the service brake, the parking brake set, the transmission in park and pressing the top "DOWN" button.

hi carol, if you go to the peugeot website the handbook is on the site, i have no book either and it really helped me, regards, sarah