Question about 2000 Chrysler 300M

5 Answers

Headlight bulb replacement on chrysler 300m

I need to change the bulb on my headlight and i dont know how. i dont have the owners manual anymore and i dont know what to do. please help.

Posted by on

  • 1 more comment 
  • Anonymous Jan 26, 2009

    I need help changing a light bulb on my headlight on my 1999 chrysler 300m

  • junkmandale1 Feb 19, 2009

    how to change head lite bulb on 2000 crysler 300m?

  • chris6664
    chris6664 Feb 13, 2019

    any Auto Parts store that you purchase the bulb from should be able to change it out for you- call ahead and ask!!



5 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Parts Required: Change all the lights at once, it is not worth the anguish of doing this over and over again
2 low-beam lights, 2 high-beam/running lights, 2 parking lights - part nos in the owners manual

A can of diet coke to clean the battery terminals is also recommended. *optional

Tools required

Ratchet set : 10mm, 7mm, 6mm sockets
Extension 12"
Large Flat screwdriver, small 4" flat screwdriver and a pair of pliers
12" Magnetic tip telescoping bit

Surgical gloves

Battery terminal cleaner * optional

Step 1:

First take off the plastic cover that cover that is across the front of the engine compartment. 6 push pins hold it in place, Use the long flat screw driver to pry them up and use the pliers to pull them off.

Gently take the plastic cover off and set it aside.

Step 2:

Next you will see 3 push pins that hold the front grill to the engine housing, using the long flat and a pair of pliers pull the 3 push pins out.

Step 3:
In the upper area of each wheel well, you will see a large 2.5" rubber grommet. Pull the rubber grommet out

Step 4:
Locate a 6mm bolt head that is driven vertically upwards. It is not visible looking at the wheel well. You have to lay down on the floor and you will find it about a foot below the grommet and at the edge of the fender. Use the the ratchet to remove this bolt headed screw. It is about a 1.5" long. Do this for both sides before going to the next step

Step 5:

Start with the passenger side as it is easier. Use the flash light and peer into the fender area from the engine compartment. You will see a nut on a bolt, and a plastic fastener.
Use the 10mm socket on the 12" extension. Insert it into the hole where the grommet was, and guide the socket on the nut head. It is about an 1" long. Be careful as you take it off, else you will be fishing for the bolt in the fender.

Step 6:
Pull on the plastic fender in the front till the bolt head and the fastener exit the fender. This has to be repeated for each side.

Step 7:
Locate 8mm bolt heads on top of the light assembly. Note it is not the Philips head - they are to level the lamps. Before undoing the bolts, check the spirit level on top of the lamp assembly and make a note of the bubbles position. You will need this when you put the assembly back. Undo both bolts, they have about an 1" of thread on the top and then you have to pull it up physically or with the use of the pliers

Step 8:
Pull the headlight assembly out - gently. Don't scratch the paint work and don't damage the rubber molding around the light assembly.

Step 8a*: If you see any salt build up on the battery terminals, pour diet coke or pepsi on the terminals, this neutralizes all the salt. Then pour some water to clean the gunk and then with a paper towel dry it. Be careful with the paper towel, as it contains sulfuric acid and is corrosive, put in in a garbage bag immediately. If you feel it has come into contact with your skin, was vigorously before continuing.

Step 9:
Note the position of the connector before you do anything. Turn the retaining rings holding each bulb counter clock wise. When you do this the bulb assembly and the connector will pull free. Two instances of this. Remove assembly, and place securely on a table

Step 10:
Locate the parking light below and turn the connector clockwise as you are looking over it. Pull out the old bulb and replace it. Do this for both sides. Turn on the parking lights to ensure they work, try the signals too. No sense it putting it all back together and nothing works. Replace the holder and bulb in reverse order. Note the unit should fit in nicely and rotate smoothly as you turn counter clockwise this time.

Step 11:
Using the 4" flat screwdriver, lift the locking pins gently and push the bulb out, Start with the low beams. Low beam has only 1 filament, high-beam/running light has 2 filaments. Put on the pair of surgical gloves, and open the pack of new bulbs, push the bulbs into the empty sockets, until the locking pins click into place. Change the low-and high beams.

Step 12:
Insert the bulb with the connector in the position you noted in step 9. Slide the mounting ring and then lock it into place by turning it clock-wise as you are looking at it from the rear of the assembly. Repeat this for both the high beam and low beam. Slide assembly back into cavity. Repeat this for the other side. Test the bulbs light correctly

Step 13:
Gently push back the front plastic so that the bolt and the plastic stud enter the fender. Pay attention to ensure that the fender lining sits correctly. Using the 12" ratchet extension and the 10mm socket mount the bolt back on and tighten. Do this for both sides

Step 14:
Using the ratchet mount the 6mm fastener on to the fender. Do this for both sides

Step 15:
Mount the jack screws on top of the headlight assembly. Tighten till the bubble in the spirit level returns to the original position. Don't push the bolt past its maximum. If it doesn't return to the original level, loosen and adjust the headlamp assembly and re-tighten. Do this for both headlamps.

Step 16:
Replace the 3 push pins that hold the front grill to the engine compartment. Replace the large plastic panel that was removed in step 1 and remount it using the 6 push pins.

Voila - you have changed all the bulbs on the front of the 1999 300M.

Estimated time:
Novice 2 hours
Advanced 1 hour
Expert 45 mins

If you found this helpful, a quick note to the author George and Anna at would be appreciated.

Posted on Apr 02, 2010

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 35 Answers

9006 xs is the low beam bulb ( the straight plug not the bent one)
The low beam can be replaced without removing the bumper portion with a little difficulty. (maybe less than removing the bumper)
Remove the black cover by pulling the plastic plugs and the 3 plastic pin and plug combos at the grill. ( pull pins up then the plug portion will come out) Remove the two long screws in the headlight (top) and then you can pull the headlight out just enough to get in there with your fingers. Turn the black plastic ring to unlock and remove bulb. You will then be able to pull the bulb up above the headlight to work with. Replace.

Posted on May 04, 2009

  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

IAnother fine piece of engineering. Even if take out the mounting screws to the head lamp assembly you can not take them out. Neither is there room in the engine compartment to take the bulb out from the back.

I have replaced the bulbs by taking the top screws of the front cowling off. To complete this task you must also take the wheel well covers off as there is one more screw (you'll need an extension for rachet) to get off.

Once these are off voila you can tilt the bra forward and easily lift out the head light assembley.

This is such a pain if your lenses are getting discolored you might as well replace them while your at it.

Total time about for me about an hr and 1/2 to replace a stinkin bulb!

I have a 1999 300M but this probably the same for changing a headlight for a Concorde or change a headlight for an LHS

Posted on Jan 31, 2009

  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Ive done it ive changed the bolb,

1. Take of the black cover, there not screws but pins carfull thought the one's with cross tip heads break easy, Then there are three main one's on the center of the black plastic cover.
2. Now u have access to the back of the headlight. Undo the mounting boult, its a small bolt but long, its on the left top side of the headlight, it loosens the headlight frame from the car frame. This gives u enough space to maybe fit your hand for jiggling room.
3. Us angle noes pliers to LIGHTLY grip the black locking brace please be carful it can break easily. Slid it back out of the way keep it on the power line remove the bad light and add the good one. Use gloves or a towel.
4. Its a little tricky getting the light out of the cassing but it came out i changed it and its working fine now. I dont understand changing a light should be something on the owners lvl, and it shouldnt be as hard as opening the hood and twisting a nob you know.

If my description isnt clear enough if sorry im not very mechanically inclined. But its pretty simple so you smarter guys should figure it out.

Posted on Mar 08, 2009

Take it to the dealer. I am changing my bulbs and I have the owners manual. I am going to autozone to look for a service manual.

Posted on Jul 24, 2008

  • jdsnsnw Apr 18, 2011

    Or, take it to body shop. Had my friends help get plastic rivets out; just did one side, it's almost 2x as much work to do 2nd side, as we ended up taking inside fender loose to get bumper cover loose. Have new bulbs on hand: 3157 for turn (new style LED wouldn't work on my '99); 9006XS for low/hi and 9005 for high beam. Get straight mounting bulbs, not 90 degree mount. TIP: much!!! cheaper on web:


1 Suggested Answer


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2000 Chrysler 300m passenger headlight won't come on after changing bulb

Hi,first check fuse,if not checkco.nnection at bulb,if not try changing bulb from other lamp and if hallagin bulb dont put your hands on the glass its self,hope this was some help,all the best

Nov 11, 2015 | Chrysler Cars & Trucks

1 Answer

I need instructions to change headlight assembly on a chrysler 300m yr 2000

If you email me i can send information that way sj196653@yahoo. Dont forget to rate my solution and leave testimonial it is how i earn my achievements Thanks in advance

Apr 22, 2012 | 2000 Chrysler 300M

1 Answer

How do I go about changing the headlight bulb on a Chrysler 300m 2000.


Mar 09, 2011 | 2000 Chrysler 300M

1 Answer

How to replace a headlight bulb in chrysler 300

you will need to unbolt bumper cover and pull out on side light is being replaced, doesnt have to come of completely but needs to pull back to get light out,remove the bolts from the top hold light asm, in, then remove top cross plate that holds hood latch and put to the side, then remove bolts and clips holding bumper cover and pull cover foward until you have room to pull light out, then remove the bulb from the rear,this bulbs are 90 degree plug type not the straight one, they dont fit, hope this helps, not bad to do, just sounds so.

Jun 09, 2010 | 2000 Chrysler 300M

1 Answer

How do you remove and replace the headlight bulb in a chrysler 300M

Find the wiring connector on the back of the headlight (under the hood.) Unplug the connector and remove the lock ring around it (turn it like a jar lid a fraction of a turn.) Wiggle the bulb out - it is held in with a rubber ring. Secure the new one in place in the same position - it won't go in the wrong way. Reinstall the lock ring and wire connector.

Jan 16, 2010 | 2006 Chrysler 300M

1 Answer

How to change the low beam headlight

It depends on the type of lighting your 300M has, in 2002 they offeredHID lighting and regular halogen lighting. You may want to get afactory service manual for your car here.Changing the bulb either way does involve removing the headlamp mostly. If you have HID you have to mind the ballasts that are attached.

Sep 28, 2009 | 2002 Chrysler 300M

2 Answers

I have read the owners manual word for word and followed it, but I cannot change the low beam bulb on my 2002 chrysler 300m

hi it not to hard there a couple of 10 mm bolts to take the headlights out then change the the bulb &reinstall headlight assy

Jul 10, 2009 | 2002 Chrysler 300M

1 Answer

Changing headlight 300m

lift the hood. the light are down behind the light assembly. simply turn large black ring and it will come out. be carefull not to touch the glass on the new one. oil from your skin will cause it to prematurely fail.

Mar 11, 2009 | 2004 Chrysler 300M

1 Answer

I need help fixing the bulb on my headlight on my 1999 300m

with that model car the headlight assembly has to be removed from vehicle. but its not that hard. there are either 7 mm bolts or 10 mm bolts and or both. then take out the headlight and replace bulb.

Jan 26, 2009 | Chrysler 300M Cars & Trucks

Not finding what you are looking for?
2000 Chrysler 300M Logo

14,353 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides