Question about 1999 Chevrolet Silverado 1500

1 Answer

Oil pan removal on a 2001 chevrolet with 5.3 engine

Posted by on

  • 4 more comments 
  • jetsetter566 Dec 01, 2010

    it is the engine oil pan that i need to rplace i have the bolts out of the pan but cannot get the pan out. the oil pan has a hole in it. do i need to pull the trans to get it out?

  • jetsetter566 Dec 01, 2010

    the truck is 2 wheel drive i have tried jacking the motor up but it will not go high enough to pull the pan out.

  • jetsetter566 Dec 01, 2010

    yes it is hitting the bellhousing but i dont think there is enough room to slide it out! i will try removing the oil level sensor still dont think i wiil have enough room to slide it out.

  • jetsetter566 Dec 01, 2010

    are you talking about the cross brace under the oil pan?

  • jetsetter566 Dec 01, 2010

    it worked i m back on the road again!!!!!! the info you gave me was right on the money, i would highly recomend this site to anyone.!!!!!!!! thanks for the info i appreciate it alot!!!!
    Jetsetter.

  • jetsetter566 Dec 01, 2010

    sent a message to the person that helped me.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,450 Answers

IF IT is 2wd remove cross brace 4wd will need to remove front differential. remove oil pan bolts and there are some bolts on the side too you will need to remove and drop pan. oil pump is not in pan if this is what you are trying to change

Posted on Dec 01, 2010

  • 4 more comments 
  • TripleTauto
    TripleTauto Dec 01, 2010

    NO you have the covers off and all from around transmission? i think you need to remove oil level sensor from pan also as it will hit oil pickup.pan will come off just gotta get in right position i assume you have it loose but it is hitting bellhousing?

  • TripleTauto
    TripleTauto Dec 01, 2010

    this is the newer body silverado with 5.3 correct? oil pan is aluminum. the center cross brace un bolts and from there the pan will drop down.

  • TripleTauto
    TripleTauto Dec 01, 2010

    I have dropped a few out but it has been a couple years now but i know they come out might need to take a pry bar and gently pry beyond bellhousing.

  • TripleTauto
    TripleTauto Dec 01, 2010

    YES should be four bolts and it comes out

  • TripleTauto
    TripleTauto Dec 01, 2010

    AWESOME!!!! glad to help out

  • slimtx35 Dec 30, 2010

    I still can't get it out

×

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to train how to drain transmission fluid out of 2001 Pontiac Azte?


1. Remove transmission oil pan (be careful oil will splash all over)
2. Remove all bolts slowly, so oil will drain slowly
3. Transmission oil pan gasket is reusable
4. Clean oil pan and let transmission oil drip then reinstall pan and gasket.(At the same time you can change the transmission oil filter.
5. Fill with transmission oil fluid (see specification) 4 liters Dexron4 fluid
6. Start the engine place transmission lever to park or neutral
7. At the same time remove plug (see pictures ) until fluid comes out the transmission plug hole. (replace the plug)



Hope it helps.
4t40e-dulq0yxevgpg4lgozqlcwg11-4-0.jpg

Apr 01, 2018 | 2001 Pontiac Aztek

1 Answer

Will i have to remove motor to replace oil pan gasket on a 2001 gmc sonoma 2.2l 5 speed


You may have to loosen the transmission also to get enough room to remove it without taking the motor out. Make sure your pan is not cracked first. Also be careful when lifting the motor as to not damage anything on top of the engine.

Nov 29, 2015 | GMC Cars & Trucks

1 Answer

How do I remove oil pan on a 2001 gmc Sonoma pick up truck to replace gasket


1993 GMC SONOMA 2.6 CYL V6 NOT 4x4 OIL PAN ...

? 2:31
https://www.youtube.com/watch?v=1KsRTlnW7Cg
Sep 27, 2011 - Uploaded by JohnSmiths8379858
trying to reomove the oil pan to this truck has been sitting for about 6 ... 1993 GMC SONOMA 2.6 CYL V6 NOT 4x4 OIL PAN REMOVAL "HELP!

Oil Pan Gasket: How to Change Oil Pan Gasket for 2001 ...

www.2carpros.com/questions/2001-gmc-sonoma-oil-pan-gasket
Mar 18, 2011 - How to change oil pan gasket for 2001 sonoma, can i get away with just raising the engine two inches to ... 2001 GMC Sonoma • 4 cylinder 2WD Automatic • 150,000 miles ... You need to remove the engine to get the sump off.

Nov 28, 2015 | GMC Cars & Trucks

1 Answer

Replacing oil pan gasket 1998 chevy silverado 305 cu.in.


REMOVAL PROCEDURE
  1. Remove the oil level indicator tube.
  2. Raise the vehicle.
  3. Remove the engine oil and the engine oil filter.
  4. Remove the oil filter adapter.
  5. Remove the starter.
  6. Remove the flywheel inspection cover.
  7. Remove the engine mount through bolts.
  8. Raise and support the engine.




  1. Remove the oil pan nuts and bolts. Note the location of any studs to assist reassembly.
  2. Remove the engine oil pan and the gasket.
  3. Clean all sealing surfaces. Refer to Oil Pan Clean and Inspect under Engine Unit Repair.
INSTALLATION PROCEDURE


  1. Install the engine oil pan and a NEW gasket. Refer to Oil Pan Installation under Engine Unit Repair.
  2. Lower the engine onto the mounts.
  3. Install the engine mount through-bolts.
  4. Install the starter.
  5. Install the flywheel inspection cover.
  6. Install the engine oil filter and the engine oil.
  7. Install the oil filter adapter.
  8. Install the oil level indicator tube.

May 04, 2015 | 1998 Chevrolet Chevrolet silverado

1 Answer

How do iremove oil pan 01 montecarlo


OIL PAN
Removal & Installation
1. Disconnect negative battery cable. Remove engine torque strut. Raise and support vehicle. Drain
crankcase. Disconnect oil level sensor electrical connector. Remove oil level sensor and oil filter.
Disconnect front exhaust pipe from manifold. Remove right front wheel and splash shield.
2. Disconnect oil cooler pipes. Disconnect A/C compressor electrical connector. Remove A/C compressor,
and position aside. Disconnect engine mounts from frame.
3. Remove flexplate access cover. Use transmission jack at transaxle to raise engine. Remove oil pan bolts
and oil pan. To install, reverse removal procedure. Install oil level sensor after oil pan is installed. Tighten
retaining bolts to specification. See TORQUE SPECIFICATIONS.

Sep 25, 2014 | 2001 Chevrolet Monte Carlo

1 Answer

How do i remove the oil pan on a 2005 chevrolet cobalt


  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Raise and support the vehicle.
  3. Drain the engine oil.
  4. Remove the engine drive belt.
  5. On the 2.0L engine, remove the intercooler pump bracket bolts from the oil pan.
  6. Remove the lower A/C compressor bolt from the oil pan.
  7. Remove the oil pan bolts.
  8. Remove the oil pan

Dec 29, 2011 | Chevrolet Cobalt Cars & Trucks

1 Answer

What is the easiest way to replace the oil pan cover gasket on a 2001 chevy s-10 4cyl. 5 speed


There is no easy way. The engine has to be hoisted or jacked high enough to allow clearance to remove the oil pan.

Aug 28, 2011 | 2001 Chevrolet S-10

1 Answer

Oil pan leak


buy a tube of sealer called Right Stuff
1. Remove the flexible exhaust pipe
2. Disconnect the downstream catalyst monitor sendor (OXYGEN SENSOR)
3. Drain engine oil
4. Remove the 15 bolts and the oil pan
5. Clean pan & surface area.
6. Apply sealer 10mm (0.40 inch) diameter of sealer
7. Position oil pan and hand-tighten the oil pan bolts
8. Start with front of oil pan tighten each bolts going around oil pan till all are tighten up.
9. Install exhaust flexible exhaust pipe
10. Connect OXYGEN SENSOR connector
11. Lower the vehicle.
12. Fill oil 5w20 (Spec)

Feb 10, 2010 | 2001 Ford Escape

1 Answer

Need to work on oil pan.


yes the mounts need to be removed and the engine as high off the cradle as poss, if it is a 4 wheel drive the engine must be pulled.

Jan 18, 2010 | 2001 Chevrolet Silverado 2500HD

1 Answer

Is there ANY way to change the oil pan gasket on a S10...


Remove motor mount bolts and rear transmission crossmember bolts or nuts,suppport engine/trans. see if u have enough clearance between pan and axle remove pan. if not, split the exh away from the manifolds. worth a try

Dec 22, 2009 | 2001 Chevrolet S-10

Not finding what you are looking for?
1999 Chevrolet Silverado 1500 Logo

Related Topics:

838 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...