SOURCE: power windows won t work
There are broken wires in the wiring harness between the frame and your driver's side door. These wires control all the windows and door locks in a 95 Jeep. Same thing happened to me. You will have to cut the rubber boot to get it off and check which wires are broken and repair them.
SOURCE: 1998 Jeep Grand Cherokee Limited inside fuse box diagram
Check out hanes book ore go dealer see if you can get print out for free
SOURCE: i need a diagram of the fuse box under the hood,
You tell us Jeep Cherokee (Laredo), in a Grand Cherokee subforum? I confussed.
If this is a Cherokee, review the Repair Manual XJ Cherokee
If this is Grand Cherokee, review ths Repair Manual ZJ-Secc-8W-Wiring-Diagrams (page 7, 9 and 10 for location, details and description). The diagramas can find it in the next pages.
I hope help yuo with this (remember rated this help). Good luck.
SOURCE: I need the fuse box index in a Jeep Cherokee 2003
go to this site it will have exactly what your looking for. a diagram and a list of what everything is.
http://www.wjjeeps.com/fuses.htm
Testimonial: "thank you very much!! i solve my problem... thank's"
SOURCE: I have a slow battery drain on a 2006 Jeep
Hi
Welcome
Jb power is Junction Block power
Here is a list of tests for this problom
IGNITION-OFF DRAW TEST
The term Ignition-Off Draw (IOD) identifies a normal condition where power is being drained from the battery with the ignition switch in the Off position. A normal vehicle electrical system will draw from five to thirty-five milliamperes (0.005 to 0.035 ampere) with the ignition switch in the Off position, and all non-ignition controlled circuits in proper working order. Up to thirty-five milliamperes are needed to enable the memory functions for the Powertrain Control Module (PCM), digital clock, electronically tuned radio, and other modules which may vary with the vehicle equipment.
A vehicle that has not been operated for approximately twenty days, may discharge the battery to an inadequate level. When a vehicle will not be used for twenty days or more (stored), remove the IOD fuse from the Junction Block (JB). This will reduce battery discharging.
Excessive IOD can be caused by:
If the IOD is over thirty-five milliamperes, the problem must be found and corrected before replacing a battery. In most cases, the battery can be charged and returned to service after the excessive IOD condition has been corrected.
1.
Verify that all electrical accessories are off. Turn off all lamps, remove the ignition key, and close all doors. If the vehicle is equipped with an illuminated entry system or an electronically tuned radio, allow the electronic timer function of these systems to automatically shut off (time out). This may take up to three minutes. See the Electronic Module Ignition-Off Draw Table for more information.
ELECTRONIC MODULE IGNITION-OFF DRAW (IOD) TABLE
Module
Time Out?
(If Yes, Interval And Wake-Up Input)
IOD
IOD After Time Out
Radio
No
1 to 3 milliamperes
N/A
Audio Power Amplifier
No
up to 1 milliampere
N/A
Central Timer Module (CTM)
No
4.75 milliamperes (max.)
N/A
Powertrain Control Module (PCM)
No
0.95 milliampere
N/A
ElectroMechanical Instrument Cluster (EMIC)
No
0.44 milliampere
N/A
Combination Flasher
No
0.08 milliampere
N/A
2.
Determine that the underhood lamp is operating properly, then disconnect the lamp wire harness connector or remove the lamp bulb.
3.
Disconnect the battery negative cable.
4.
Set an electronic digital multi-meter to its highest amperage scale. Connect the multi-meter between the disconnected battery negative cable terminal clamp and the battery negative terminal post. Make sure that the doors remain closed so that the illuminated entry system is not activated. The multi-meter amperage reading may remain high for up to three minutes, or may not give any reading at all while set in the highest amperage scale, depending upon the electrical equipment in the vehicle. The multi-meter leads must be securely clamped to the battery negative cable terminal clamp and the battery negative terminal post. If continuity between the battery negative terminal post and the negative cable terminal clamp is lost during any part of the IOD test, the electronic timer function will be activated and all of the tests will have to be repeated.
5.
After about three minutes, the high-amperage IOD reading on the multi-meter should become very low or nonexistent, depending upon the electrical equipment in the vehicle. If the amperage reading remains high, remove and replace each fuse in the Power Distribution Center (PDC) , one at a time until the amperage reading becomes very low, or nonexistent. (Refer to 04 - Vehicle Quick Reference/Fuse Locations and Types - Specifications) for the appropriate wiring information for complete PDC and TIPM fuse, circuit breaker, and circuit identification. This will isolate each circuit and identify the circuit that is the source of the high-amperage IOD. If the amperage reading remains high after removing and replacing each fuse and circuit breaker, disconnect the wire harness from the generator. If the amperage reading now becomes very low or nonexistent, diagnose and repair the Charging System as necessary. After the high-amperage IOD has been corrected, switch the multi-meter to progressively lower amperage scales and, if necessary, repeat the fuse and circuit breaker remove-and-replace process to identify and correct all sources of excessive IOD. It is now safe to select the lowest milliampere scale of the multi-meter to check the low-amperage IOD.
CAUTION:
Do not open any doors, or turn on any electrical accessories with the lowest milliampere scale selected, or the multi-meter may be damaged.
6.
Observe the multi-meter reading. The low-amperage IOD should not exceed thirty-five milliamperes (0.035 ampere). If the current draw exceeds thirty-five milliamperes, isolate each circuit using the fuse and circuit breaker remove-and-replace process in Step #5 . The multi-meter reading will drop to within the acceptable limit when the source of the excessive current draw is disconnected. Repair this circuit as required; whether a wiring short, incorrect switch adjustment, or an inoperative component is the cause.
74 views
Usually answered in minutes!
×