Rear brake diagram

have it deone by a pro they need to check the rotor run out as well as replacing the pads

Removal
1.Remove rear wheel and tire assembly from vehicle.

2.Remove rear brake drums from hub and bearing assemblies after loosening the two brake drum screws.

3.Be sure that the parking brake pedal is in the release(most upward) position.

4.Completely loosen square nut of the rear parking brake cable. Then create slack in the rear parking brake cables.

5.Remove adjuster spring from adjust lever and brake shoe.

6.Remove adjust lever and turn the adjusting wheel of adjuster assembly to the direction of the arrow as shown.

7.Remove the strut spring and the lower retracting spring from the brake shoe.

8.Remove the upper return spring from the brake shoe.

9.Remove brake back plate hold down spring and pin from the leading brake shoe assembly.

10.Remove the leading brake shoe. Then remove the adjuster assembly, strut and anchor spring from the trailing brake shoe.

11.Remove the trailing brake shoe from the brake back plate after removing hold down spring and pin.

12.Remove the trailing brake shoe from the rear parking cable.

13.Remove parking pivot lever from the leading brake shoe.

Replacement
1.Lubricate the eight shoe contact areas on the back plate and anchor.

2.Install the trailing brake shoe to the rear parking cable.

3.Install trailing brake shoe on brake back plate and install the trailing brake shoe hold down spring and pin on the brake shoe.

4.Tighten the square nut of rear parking cable.

5.Install the anchor spring then install adjuster assembly, and strut.

6.Install leading brake shoe on brake back plate.

7.Install the brake shoe upper return spring, strut spring and the lower retracting spring to the brake shoe.

8.Properly rotate the adjusting wheel of adjuster assembly to the direction of the arrow in as shown.

9.Install the adjuster spring on the adjust lever and leading brake shoe assembly.

10.Install the leading brake shoe hold down spring and pin on the brake shoe.

11.Adjust brake shoes assemblies so as not to interfere with brake drum installation.

12.Install the rear brake drums on the hubs.

13.Check and adjust whether the pedal stroke in the specification.(Refer to section BR Gr./On-vehicle service/Pedal stroke of parking brake)

14.Install wheel and tire.

15.Push the parking brake pedal to the floor once and release pedal. This will automatically remove the slack from and correctly adjust the parking brake cables.

16.Test the vehiche on the road. The adjust will continue the brake adjustment during the road test of vehicle.

Inspection
1.Inspect the disassembled parts for wear, rust or damage.

2.Measure the thickness of brake shoe lining.
Standard : 0.17 in (4.5 mm)
Minimum : 0.04 in (1 mm)

3.If the shoe lining is less than minimum or shows signs of uneven wear, replace new one.

4.Measure the inside diameter of the brake drum.
Standard : 10 in (254 mm)
Maximum : 10.07 in (256 mm)

5.If the inside diameter of the brake drum is more than maximum or shows signs of uneven wear, replace new one.

6.Inspect the lining and drum for proper contact. If the contact condition is improper, repair it with a grinder or replace the brake shoe assembly.

https://www.google.com/search?q=2003+Kia+Sedona+Rear+Brakes+diagram&oq=2003+Kia+Sedona+Rear+Brakes+diagram&sugexp=chrome,mod=0&sourceid=chrome&ie=UTF-8

Get a repair manaual from auto zone on your truck. Also long shoes goes on back torward bumper.

THE Spring is Behind the rear Drum,Of the Car..OK...

Brake Shoes Removal & Installation To Remove:

1. Raise and safely support rear of vehicle.
2. Remove rear wheel assemblies.
3. Release parking brake.
4. Remove brake drum.

Rear brake shoe assembly

1. Using an appropriate brake spring tool, unhook upper return spring from rearward brake shoe.
2. Push retainer springs IN and turn to remove tension pins.
3. Lower brake shoe assembly and remove lower return spring.
4. Remove brake shoe assembly from back plate.
5. Disconnect parking brake cable from lever and remove brake shoe.
6. Remove parking brake lever from brake shoe.

To Install:

1. Install parking brake lever to rearward brake shoe.
2. Secure lever to brake show with a NEW U-clip.
3. Pinch U-clip closed.
4. Connect parking brake cable to rearward brake shoe.
5. Install self-adjuster lever spring on front brake shoe.
6. Assemble clevises, adjuster bolt and upper and lower return springs.
7. Apply a light coat of grease (Molykote 44MA or equivalent) to sliding surfaces.
8. Install brake shoe assembly onto back plate.
9. Install tension springs.
10. Using an appropriate brake spring tool, unhook upper return spring to rearward brake shoe.
11. Install brake drum.
12. Install rear wheel assembly.
13. Lower vehicle.
14. Adjust self-adjusting brakes by pressing brake pedal several times.

there should be several springs. first there are (2) real short springs that hold the shoes to the dust cover/back plate. they go in the center of each shoe. then there is a short spring that goes at the bottom where the adjuster is located. there should be a hole in each shoe. finally there is a long spring that goes at the top where your brake cylinder is and this is what gets attched last after your emergancy brake levers are placed between the shoes .

help is here:
http://autos.groups.yahoo.com/group/villagerquest/

Drum Removal

1. Remove the rear wheel and the tire assembly. Refer to Section 204-04 .

1. Retract the brake shoes and loosen the brake adjuster screw.

1. Remove the brake drum.

----------------------
May require big hammer to loosen drum from axle flange. Hit between the the lugs, not on them.

------------------------------------------------------------------------------
#10 is access plug to back off adjusting wheel.


Item Part Number Description 1 2261 Rear wheel cylinder 2 — Dust boot (part of 2128) 3 2197 Wheel cylinder piston (part of 2261) 4 — Cup (part of 2128) 5 2204 Wheel cylinder piston cup spring (part of 2128) 6 — Wheel cylinder housing (part of 2261) 7 — Brake shoe hold-down pin 8 — Access hole (part of 2212) 9 — Rear brake bleeder screw (part of 2261) 10 — Access hole plug 11 — Rear wheel cylinder bolt 12 2212 Rear brake backing plate 13 — Rear brake backing plate bolts 14 2N790 Parking brake lever clip 15 — Spring washer 16 — Secondary brake shoe and lining (part of 2200) 17 — Brake shoe hold-down spring (part of 2B514) 18 — Lower retracting spring (part of 2B514) 19 2A637 Parking brake lever 20 — Parking brake lever pin 21 2A177 Brake shoe adjusting lever 22 — Adjuster lever pin (part of 2A177) 23 — Primary brake shoe and lining (part of 2200) 24 — Upper retracting spring (part of 2B514) 25 2041 Brake adjuster screw

--------------
Shoes Removal

Take a picture and remember how each part goes and attaches

1. Remove the brake drum, refer to Drum in this section.

1. Remove the upper retracting spring.

1. Remove the lower retracting spring.

1. Remove the self-adjuster.

1. Remove the hold-down springs.

1. Remove the parking brake lever clip and the parking brake lever.

looked in the book and confirmed with an online diagram, for the spring positions and proper spring to bracket plate assembly. Thanks for all your help and sugesstions

If this is for the rear here you go.
http://www.google.com/search?hl=en&client=firefox-a&rls=org.mozilla:en-US:official&hs=2rX&ei=CtiNSdOoLZmktQPLvaWDCQ&sa=X&oi=spell&resnum=0&ct=result&cd=1&q=Ford+Focus+rear+brake+diagram&spell=1