Question about 2003 Dodge Durango

1 Answer

I recently replaced the front rotors, brake pads and master cylinder in my 2003 Durango. I've since discovered that the brake lights are not working, including the 3rd brake light in the tailgate. I checked and the top bulb in the left and right assemblies as well as all 3 bulbs in the 3rd brake light assembly were burned. The tail lights, reverse lights and signals work fine (other than the 2 top bulbs). I replaced those 2 bulbs as well as the 3 bulbs in the 3rd brake light assembly but still no brake lights. I then replaced the brake light switch and still nothing. Any help would be greatly appreciated.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 381 Answers

Hello, Well there is not much more it could be unless you have a shorted wire or a burned fuse. I would normally think that the turn signal canceler was bad but the 3rd brake light will still work if that is bad so I would check all fuses and for bare or shorted wires.

Posted on Jan 18, 2011

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2007 nissan quest 3.5S mini van is in almost perfect condition until I recently discovered something deviating from what I know is common to brakes. I do all maintenance work to my cars (nissan VW,...


Master cylinder and/or brake booster could be the problem. A tiny bit of air in the system will effect your braking abilty. A fault in the ABS system would prompt the computer to trigger the ABS light. If you have brake shoes on the rear, make sure they are properly adjusted. Hope this helps.

Jul 04, 2011 | 2007 Nissan Quest 3.5 Minivan

1 Answer

Should the center spindle nut and 2 torgued phillip head screws be removed to replace front brake rotor on 1999 honda accord lx


will try to help. 1st remove the wheel, then remove the 2 caliper bolts that hold the brake caliper on. after removal of brake caliper, [it should just pull off after the 2 bolts are removed] replace the brake pads[be sure to apply anti squeal lube to the outer side of the pads..not the pad itself,the one not contacting the brake rotor] install the pads, the you will need a C clamp to push the brake caliper pistons back into the caliper. i've used this installation easily. use the old pad ,place it against the caliper piston,then apply the C clamp and push the caliper piston back into the brake caliper, then the brake caliper will slide back over the new pads easily, no need to bleed the brakes if you use this solution. replace the brake caliper bolts, then go to next side and repeat the process. after the replacement of the front brake pads,pump the brakes with engine running!!! it's really a simple process. be sure the brake pads are facing the brake rotors with the [pads] facicing the rotors. no metal facing metal. easy! if you have added brake fluid recently, do not be alarmed if you see fluid coming out of the brake master cylinder,when you use the C clamp to collaspe the brake caliper back into the recessed position. [as always when you have to add brake fluid to the brake master cylinder,it only means your brakes are wearing naturally. if you have a vibration in front wheels or steering wheel when braking, you have a brake rotor or both front brake rotors that need replacement with your brakes also. hope this helps and as always, please get a second opinion if you have doubt. an expert will be happy to help. thank you for choosing fixya.com

Dec 22, 2010 | 1999 Honda Accord

1 Answer

Pontiac Vibe 2003. After a full stop of the car, there is a slow lowering of a pedal of a brake. At emergency braking the brake system works normally. Front pads and rotors are replaced, rear pads and...


If there are no fluid leaks than I would bet you replaced the master cylinder with a re-manufactured unit instead of new. The re-manufactured ones are fine as long as you don't mind trying several of them to get one that works. If it is re-manufactured return it and get a new master cylinder.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Oct 05, 2010 | Pontiac Vibe Cars & Trucks

3 Answers

Brakes are going to the floor most of the way checked rear brakes and they are still good bleed them and problem still there


Normally when the brake pedal goes almos to the floor it is an indication of low brake fluid. Low brake fluid is an indication that front and/or rear brakes are wearing. As the brake pads wear down more brake fluid will be required in the wheel cylinders or calipers. Hint, the front brakes usually wear much faster than the rear due to the fact that the fronts due a much greater braking function that the rear. Check the front pads. Don't let them get down to the metal scraping metal stage before you change them out. This causes unnessary damage to the rotors. Look at your master cylinder on the firewall under the hood in front of the steering wheel. If the fluid level is belowhte "max" mark add fluid. Low fliud should also show as a red "brake" light on your dash, but not always.

Sep 08, 2010 | 1994 Honda Civic

1 Answer

How do you replace the front and rear brakes in a 2003 pontiac Grand Prix


Removal & Installation Front To Remove:
  1. Inspect the fluid level in the master cylinder reservoir. Remove fluid from the reservoir until the level is lower then half way between the MAX and MIN levels.
  2. Remove the tire and wheel assembly.
  3. Install 2 wheel nuts to secure the rotor on the hub.
  4. Remove the bottom brake caliper pin bolt.
  5. Pivot the brake caliper body upward and secure out of the way. Do NOT disconnect the hydraulic brake flexible hose from the caliper.
  6. Compress the piston back into the bore using a C-clamp. Figure of brake assembly with caliper raised showing brake pads in mounting bracket gmpc_l4.gif

  7. Remove the inboard and outboard brake pads from the brake caliper bracket.
To Install:
  1. Install the brake pad retainers and both brake pads into the caliper bracket.
  2. Pivot the brake caliper down over the brake pads and into the brake caliper bracket. Insert the lower brake caliper pin bolt and torque bolt to 70 ft-lb. (95 Nm).
  3. Reinstall the tire and wheel assembly.
  4. Lower the vehicle.
  5. Refill the master cylinder. Pump the brake pedal several times to seat the pads against the rotor.
  6. Check the master cylinder level and add fluid as necessary.
Rear To Remove:
Rear disc pads R&I gm-09-00-492.gif

  1. Inspect the fluid level in the master cylinder reservoir. Remove fluid from the reservoir until the level is lower then half way between the MAX and MIN levels.
  2. Remove the tire and wheel assembly.
  3. Install 2 wheel nuts to secure the rotor on the hub.
  4. Remove the upper caliper mounting bolt.
  5. Pivot the caliper down to access the pads.
  6. Remove the inboard and outboard pads from the caliper bracket.
  7. Remove the brake pad clips from the caliper bracket.
  8. Compress the piston back into the bore using a C-clamp and the old inner pad.
To Install:
  1. Install new brake clips in the caliper bracket.
  2. Install the inboard and outboard pads in the caliper bracket.
  3. Pivot the caliper up over the pads.
  4. Reinstall the upper mounting bolt and tighten to 32 ft. lbs. (44 Nm).
  5. Remove the 2 wheel nuts securing the rotor.
  6. Reinstall the tire and wheel assembly.
  7. Refill the master cylinder. Pump the brake pedal several times to seat the pads against the rotor.
  8. Check the master cylinder level and add fluid as necessary.
prev.gif next.gif

Aug 26, 2010 | 2003 Pontiac Grand Prix

1 Answer

I have replaced the brakes, rotors, calipers and master cylinder on a 2003 dodge durango, i bench bleed the master cylinder, and have spent 2 days now bleeding the brakes, only to end up with a spongy...


sorry you went thru all of that... those vehicles have an issue with power brake boosters. one more thing to replace...Or, you still have air in the system...

Jul 10, 2010 | 2003 Dodge Durango

1 Answer

Brake pad replacement 2004 audi a4 and rotor how do i do and what tools are neccessary?


YOU NEED REMOVE A LITTLE BRAKE FLUID FROM MASTER CYLINDER.THEN YOU RAISE VECHICLE SAFELY.SUPPORT IT WITH JACK STAND.MAKE SURE VECHICLE IS ON LEVEL SOLID GROUND.REMOVE TIRE OR WHEEL.THEN YOU NEED A LARGE C - CLAMP.PLACE C - CLAMP OVER BRAKE CALIPER AND BRAKE SHOE BACKING.TIGHTEN C - CLAMP JUST ENOUGH PUSH CALIPER PISTON BACK IN CYLINDER BORE TO REMOVE CALIPERS FROM ROTORS.TO REMOVE BRAKE CALIPER YOU NEED 2 OPEN AND BOX END WRENCHES ONE TO HOLD CALIPER SLIDE PINS AND THE OTHER WRENCH FOR LOOSEN CALIPER BOLTS.THEN YOU REMOVE CALIPER AND REPLACE FRONT BRAKE SHOES.IF YOU NEED TO REMOVE BRAKE ROTORS JUST REMOVE THE BRAKE CALIPER CARRIER SUPPORT BOLTS THE REMOVE THE BRAKE CALIPER CARRIER SUPPORT THEN REMOVE ROTOR.YOU NEED TO REPLACE BOLTS WITH NEWS AND USE LOCK TIGHT.THEN YOU PUT IN NEW BRAKE PADS IN CALIPER PUT CALIPER BACK ON SUPPORT CARRIER.REPLACE WITH NEW BOLTS USE LOCK TIGHT THEN TORQUE BOLTS TO 26 FT LBS.MAKE SURE MASTER CYLINDER COVER IN PLACE.WHEN YOU FINISH REPLACING BOTH FRONT BRAKE PADS PUMP BRAKE PEDAL TO SEAT BRAKE SHOES AGAINST BRAKE ROTORS SO YOU WILL HAVE FIRM BRAKES WHEN YOU APPLY THEM. THEN CHECK YOUR BRAKE FLUID LEVEL IN MASTER CYLINDER MAKE SURE ITS NOT LOW. MAKE SURE YOU HAVE FIRM BRAKES BEFORE DRIVING.IF YOU HAVE ANY PROBLEMS CHANGING FRONT BRAKE PADS YOU CAN GO TO ANY AUTO PARTS STORE AND BUY A HAYNES REPAIR MANUAL.

Jun 16, 2010 | 2004 Audi A4

1 Answer

My 2003 dodge durango is making a grinding noise in the front left side what is it?


it could be the brake pads worn to the rotor or it could be the wheel bearing. just take the wheel off and inspect the brake pads and rotor for wear

Mar 23, 2010 | 2003 Dodge Durango

1 Answer

Replace front brake pads on a 2003 dodge durango,after pumping


could be a bad master cylinder or a power booster the part that the master cylinder attatches to. also check whell cylinders to make sure they are not leaking.

Jul 04, 2009 | 2003 Dodge Durango

Not finding what you are looking for?
2003 Dodge Durango Logo

309 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...