I have a 93 chevy z71. I can't get the auto locking hubs to lock. My transfer chase works. But when i try to shift it into 4hi or 4low the 4x4 fuse in the fuse box will blow

you need to be in neutral with the truck moving less than 3 mph for the truck to allow itself to shift into four lo

Check the fuse to the 4x4, if the fuse is good then check the 4x4 electric motor actuator on the transfer case. You should hear it work from 2wd, 4hi to 4low and back to 2wd with the push of the switch. if you don't hear it working then check the wire harness at the actuator motor, look for any damages like corrosion or cracked wire connector clips. If the 4x4 actuator is working on the transfer case, then the front hub 4x4 actuator may have gone bad and that's located on the front differential. It's common for the clip there to corrode and break and is an easy fix with a new collar pin, at worst it's the diaphragm on the vacuum actuator that is located under the battery tray. There is a vacuum switch on the top of the transfer case, driver side but when that fails, your front hub stay's locked in the on position. Good luck and keep me posted and hope it's a simple fuse that has gone bad. You can pick up all these parts at Auto Zone or Parts Source and they will have the step by step instructions for you to get the job done with common tools.

Check the fuse to the 4x4, if the fuse is good then check the 4x4 electric motor actuator on the transfer case. You should hear it work from 2wd, 4hi to 4low and back to 2wd with the push of the switch. if you don't hear it working then check the wire harness at the actuator motor, look for any damages like corrosion or cracked wire connector clips. If the 4x4 actuator is working on the transfer case, then the front hub 4x4 actuator may have gone bad and that's located on the front differential. It's common for the clip there to corrode and break and is an easy fix with a new collar pin, at worst it's the diaphragm on the vacuum actuator that is located under the battery tray. There is a vacuum switch on the top of the transfer case, driver side but when that fails, your front hub stay's locked in the on position. Good luck and keep me posted and hope it's a simple fuse that has gone bad. You can pick up all these parts at Auto Zone or Parts Source and they will have the step by step instructions for you to get the job done with common tools.

Check the fuse to the 4x4, if the fuse is good then check the 4x4 electric motor actuator on the transfer case. You should hear it work from 2wd, 4hi to 4low and back to 2wd with the push of the switch. if you don't hear it working then check the wire harness at the actuator motor, look for any damages like corrosion or cracked wire connector clips. If the 4x4 actuator is working on the transfer case, then the front hub 4x4 actuator may have gone bad and that's located on the front differential. It's common for the clip there to corrode and break and is an easy fix with a new collar pin, at worst it's the diaphragm on the vacuum actuator that is located under the battery tray. There is a vacuum switch on the top of the transfer case, driver side but when that fails, your front hub stay's locked in the on position. Good luck and keep me posted and hope it's a simple fuse that has gone bad. You can pick up all these parts at Auto Zone or Parts Source and they will have the step by step instructions for you to get the job done with common tools.

Check the fuse to the 4x4, if the fuse is good then check the 4x4 electric motor actuator on the transfer case. You should hear it work from 2wd, 4hi to 4low and back to 2wd with the push of the switch. if you don't hear it working then check the wire harness at the actuator motor, look for any damages like corrosion or cracked wire connector clips. If all electrical is in good working order, replace the actuator motor. If the 4x4 actuator is working on the transfer case, then the front hub 4x4 actuator may have gone bad and that's located on the front differential. It's common for the clip there to corrode and break and is an easy fix with a new collar pin, at worst it's the diaphragm on the vacuum actuator that is located under the battery tray. There is a vacuum switch on the top of the transfer case, driver side but when that fails, your front hub stay's locked in the on position. Good luck and keep me posted and hope it's a simple fuse that has gone bad. You can pick up all these parts at Auto Zone or Parts Source and they will have the step by step instructions for you to get the job done with common tools.

Check the fuse to the 4x4, if the fuse is good then check the 4x4 electric motor actuator on the transfer case. You should hear it work from 2wd, 4hi to 4low and back to 2wd with the push of the switch. if you don't hear it working then check the wire harness at the actuator motor, look for any damages like corrosion or cracked wire connector clips. If the 4x4 actuator is working on the transfer case, then the front hub 4x4 actuator may have gone bad and that's located on the front differential. It's common for the clip there to corrode and break and is an easy fix with a new collar pin, at worst it's the diaphragm on the vacuum actuator that is located under the battery tray. There is a vacuum switch on the top of the transfer case, driver side but when that fails, your front hub stay's locked in the on position. Good luck and keep me posted and hope it's a simple fuse that has gone bad. You can pick up all these parts at Auto Zone or Parts Source and they will have the step by step instructions for you to get the job done with common tools.

Check the fuse to the 4x4, if the fuse is good then check the 4x4 electric motor actuator on the transfer case. You should hear it work from 2wd, 4hi to 4low and back to 2wd with the push of the switch. if you don't hear it working then check the wire harness at the actuator motor, look for any damages like corrosion or cracked wire connector clips. If the 4x4 actuator is working on the transfer case, then the front hub 4x4 actuator may have gone bad and that's located on the front differential. It's common for the clip there to corrode and break and is an easy fix with a new collar pin, at worst it's the diaphragm on the vacuum actuator that is located under the battery tray. There is a vacuum switch on the top of the transfer case, driver side but when that fails, your front hub stay's locked in the on position. Good luck and keep me posted and hope it's a simple fuse that has gone bad. You can pick up all these parts at Auto Zone or Parts Source and they will have the step by step instructions for you to get the job done with common tools.

yea its not shifting again like before ? sounds like your transfer case solonoid has possably gone bad again .. these are a sometimes dont work item .. It is what shifts the transfer case into gear and it might be a little worn or weathered and not letting the switch kick it in gear all the way from the N position. thanks Jerry holler if you need more.

Hi ..i had the same same problem in my k3500,check 4x4 fuse first .if thats blown replace it if blows when you put in 4x4 go under the car and unplug the actuator at the front diff.go back in the cab and put another fuse in, shift into 4x4 if the fuse does not blow this time you will need a new actuator.
thats what happened with mine and now 4x4 is sweet.i thought mine worked to at the start until i got bogged and noticed my front wheels wernt turning.

do you have outside locking hubs?