I understand these cars have a sealed clutch system. When they fail you replace the whole kit master,hydrolic pipe and slave (comes in one piece). Search on ebay maybe £45 or so.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Most likely the slave cylinder is leaking. When a master cylinder leaks it usually wets the back of the clutch pedal and then disappears into the carpet.
Slave cylinder seals usually last almost indefinitely and when they fail it is usually due to fluid contamination, especially corrosion-causing moisture roughening the cylinder bore, though a long period working in the same range of movement can create a wear ridge in the bore. Replacing the clutch probably forced the cylinder into a new range of movement and the seal didn't like the wear ridge.
Replacing the master cylinder would probably pay dividends over the longer term...
Check the hydraulic clutch operation. This is a clutch master cylinder with a reservoir on the firewall, and a clutch slave cylinder down on the bell housing of the transmission, with a steel tube running from the master to the slave cylinder. When clutch pedal is depressed, hydraulic fluid (brake fluid) is forced from the master to the slave. The slave cylinder should push out a little plunger that contacts the clutch fork lever-pushing it forward to engage the clutch.
Add brake fluid to the reservoir if needed. Watch the plunger on the slave cylinder: if it moves little, or not enough, try bleeding the slave from the bleeder valve. They are bled just like brakes. If bleeding doesn't help, your clutch master or the slave may need replacing. The master cylinder, like a brake master, has internal seals that hold hydraulic pressure, so force can be applied to the plunger on the slave cylinder.
FIRST REMOVE ALL OLD FLUID FROM CLUTCH MASTER CYLINDER YOU CAN USE A SIPHON YOU HAND PUMP.AUTO PARTS STORES SELLS THE HAND PUMP SIPHONS. THEY DONT COST MUCH AND KEEP FROM MAKING A MESS.SIPHON OUT MUCH AS YOU CAN THE OLD FLUID IN THE CLUTCH MASTER CYLINDER.THEN POUR IN THE NEW FLUID DOT 3 BRAKE FLUID IN CLUTCH MASTER CYLINDER.OKAY YOU NEED A HELPER.LOCATE THE SLAVE CYLINDER.REMOVE SLAVE CYLINDER HOLD SLAVE CYLINDER 45 DEGREES WITH BLEEDER SCREW LOCATED AT THE HIGHEST POINT.HAVE A SMALL DRAIN PAN UNDER SLAVE CYLINDER.HAVE HELPER FULLY DEPRESS AND HOLD THE CLUTCH PEDAL THEN OPEN BLEED SCREW.CLOSE THE BLEED SCREW AND HAVE HELPER RELEASE THE CLUTCH PEDAL.REPEAT THIS PROCESS UNTIL ALL THE OLD BRAKE FLUID AND AIR BUBBLES LEAVES THE HYDRALIC SYSTEM AND WHEN YOU CAN SEE GOOD STREAM CLEAN FLUID NO BUBBLES YOU HAVE GOOD SOLID CLUTCH ALL IS GOOD.MAKE SURE THROUGH THE BLEEDING PROCESS YOU DONT LET CLUTCH MASTER CYLINDER RUN DRY OR YOU WILL HAVE TO START OVER.KEEP CLUTCH MASTER CYLINER FULL BRAKE FLUID WHILE DOING THE WHOLE BLEEDING AND FLUSHING PROCESS.
on the transmission there is a slave cylinder that works like a brake cylinder, when you apply pressure to the clutch pedal a rod inside the vehicle under the dash pushes into a clutch master cylinder, (almost like a brake master cylinder without the reservoir, as the clutch master cylinder works off the brake master cylinders reservoir) the plunger in the clutch master cylinder applies fluid pressure to the slave cylinder,(located down on the trans near the clutch fork assembly) which projects a piston rod into the clutch fork dis-engaging the clutch. To bleed the clutch slave cylinder locate the bleeder screw on the slave cylinder,break loose so it loosens and tightens easily. Check fluid in brake master cylinder reservoir,fill if needed, while bleeder on the slave cyl is closed have a helper push clutch pedal to floor and back 7-8 times, (At first the clutch might stay at the floor, just pull it up by hand or foot and continue) after several pumps with no rest time push pedal to the floor and hold down with foot pressure, at this time loosen the bleeder on slave untill fluid leaks out, watch for air bubbles, close bleeder and repeat untill there is no sign of air bubbles, (make sure to check fluid in the brake master cylinder and keep fill as needed, do not let fluid get less than 1/2 empty as it might **** air and you will have to start over) If this does not bring clutch to operate then you need to check if slave cylinder is reachig its full extension of push rod or not. If it is not then you will have to replace the clutch master cyl or the clutch slave cyl or both as seals are bad and wont hold pressure. Or you need to inspect the clutch fork,the throw-out bearing, or the pressure plate fingers and clutch plate for failure or broken bent parts. I hope it turns out to be a easy fix on that clutching thing.
The brake system and the clutch master cylinder have the same fluid tank, look at the brake master cylinder fluid tank, on the right hand side about half way up is a hose that goes over to the clutch master cylinder, if fluid level is not above this hose the clutch will stop functioning. If the clutch slave cylinder, mounted on the front side of transmission bellhousing, leaks then the clutch will stop functioning. The slave cylinder has a bleed screw, check these items and fill and bleed as neccessary. Hope this helps, let me know.
The clutch is not adjustable,it is a fluid clutch.It has to be a leak,or the slave cylinder,and,or, the master cylinder are bad,It does not have to be leaking to be bad,but it is one of the two.Rate please,thank you.
Thn the problem is the clutch master cylinder, it should build up pressure, ok try out this, remove the pipe which is going to the slave cylinder either from the clutch master cylinder or at the clutch slave cylinder and get someone to pump the pedal while you block the pipe and see if there is fluid thrown out with pressure.If there is pressure there thn fit back the pipe and refill the reserviour wth brake fluid and open the bleeding nipple at the slave cylinder let some fluid pour out and tighten it and thn pump the pedal and retry bleeding.
If there is no pressure at the pipe thn its the clutch master cylinder.
Hope this helps!
×