1997 Chevrolet S-10 Pickup Logo
Anonymous Posted on Feb 12, 2011

Replacing the water pump on 96 chevy S10, - 1997 Chevrolet S-10 Pickup

1 Answer

Duane Wong

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

  • Chevrolet Master 6,826 Answers
  • Posted on Feb 12, 2011
Duane Wong
Chevrolet Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Joined: Jun 20, 2010
Answers
6826
Questions
6
Helped
2861512
Points
20234

Water Pump Removal & Installation 2.2L Engine To Remove:

  1. Drain the cooling system.
  2. Remove fan assembly.
  3. Loosen the water pump pulley bolts.
  4. Remove or disconnect the following:
    • Drive belt Replacing the water pump on - gm-03-22-606.gif

    • Water pump drive pulley bolts
    • Water pump drive pulley
    • Radiator inlet hose clamp and hose from the water pump
    • Water pump mounting bolts gm-03-22-605.gif

    • Water pump
    • Water pump gasket


To Install:
  1. Clean the mating surfaces.
  2. Install or connect the following:
    • Water pump gasket
    • Water pump Note: Apply a sealer (GM P/N 12346004) or equivalent to the bolt threads
    • Water pump mounting bolts
      1. Torque to: 18 ft lbs (25 Nm)
    • Water pump pulley and bolts
      1. Torque to: 18 ft lbs (25 Nm)
    • Radiator hose and clamp
  3. Fill with coolant.
  4. Check for leaks.
4.3L Engine To Remove:
  1. Drain the cooling system.
  2. Remove fan assembly.
  3. Loosen the water pump pulley bolts.
  4. Remove or disconnect the following:
    • Drive belt gm_truck_43_wppulley.gif

    • Water pump drive pulley bolts
    • Water pump drive pulley
    • Radiator inlet hose clamp and hose from the water pump
    • Water pump mounting bolts gm_truck_43_waterpump.gif

    • Water pump
    • Water pump gasket
gm_truck_43_waterpump_gsk.gif

To Install:
  1. Clean the mating surfaces.
  2. Install or connect the following:
    • Water pump gasket
    • Water pump Note: Apply a sealer (GM P/N 12346004) or equivalent to the bolt threads
    • Water pump mounting bolts
      1. Torque to: 30 ft lbs (41 Nm)
    • Water pump pulley and bolts
      1. Torque to: 18 ft lbs (25 Nm)
    • Radiator hose and clamp
  3. Fill with coolant.
  4. Check for leaks.
next.gif

  • Duane Wong
    Duane Wong Feb 12, 2011

    Click on X's for diagrams.

×

1 Related Answer

Anonymous

  • 12 Answers
  • Posted on Dec 17, 2008

SOURCE: 1996 Chevy S10 4x4 - Dash lights need replacing

not easy, you have to remove bottom plastic from underneath the dash, there should be two or three you don't have to go to the passenger side, then the front contour snaps off bring your shifter arm al the way down to 1st gear and the steering colomn as well on that plastic contour you have the 4x4 switch to unplug, rear wiper switch, light switch, and rear hatch switch, wiggle the plastic out, now you should see the instrument cluster there should be two to 4 screws holding that in should be 7 mm screws, now careful, if you have the analog cluster you have the speedmeter cable in back to unclip, if digital odometer it's plugged in directly into the dash and there could be an additional plug on top of the cluster, if the cluster came out unclip the backing and you should see the back of the bulbs but careful some are twist off and many others are soudered on that board you aoto parts counter should have these lights in stock no sweat.... good luck

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

I have a 96 Chevy Blazer 4 door I've change the ignition switch starter all that good old stuff if I turn the key and jumper by the starter it will run I have liked it just no crank no start

1989 Chevy blazer 4.3 won't start..I have ... - CarGurus

www.cargurus.com > Questions > Chevrolet > BlazerCarGurusJan 30, 2013 - 96 Chevy S10 Blazer with 4.3 L engine vortex will turn over but won'tstart. ... i a 93 k5 blazer 5.7tbi in cold weather it will not start, if i hook jumper ... was told it just needed a Fuel pump, I replaced the Fuel pump, and the Filter, ...
0helpful
1answer

I have a 96 Chevy s10 it cranks but won't start I

You need to find out if the fuel pump is working, getting gas up to the engine.
If the pump is working and seen to have good fuel pressure, check ignition by checking for spark.. To work, the engine needs, you know, gas, air, spark, and compression. Why people say, check for gas, check for spark.
0helpful
2answers
0helpful
1answer

My 96 s10 blazer has fuel pressure to the injectors whitch are spider injectors but will not start

I had a 2000 chevy Blazer that had the same problem. I ended up replacing the spider injectors from the local parts house and solved my problem. The computer was sending to open them but they didnt in which it wouldnt run. Hope that helps.
0helpful
1answer

Where is the starter on a chevy s10 1998

http://www.ehow.com/how_6114322_replace-starter-chevy-s10.html Just replaced on my 96 a month ago this should help Mine was under the driver side of the truck
3helpful
1answer

I am replacing a starter on a 96 s10 4wd and I

Right side. For any car, just follow the large positive battery cable, it always ends at the starter.
1helpful
1answer

Installing a blower motor in a 98 Chevy Blazer

96 chevy S10 p/u truck 4cyl 2.2 liter
shift solenoid electrical problem
Not finding what you are looking for?

1,757 views

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...