My hatchback is stuck in the locked position I cannot get it open.2001 jeep grand cherokee laredo 6 cyliner . Loaded and closed the hatchback would not open to unload. tried pushing while holding the electronic unlock button.

Jeep Crank Sensor Replacement, P Codes P0351, P1391 ...

? 6:24
www.youtube.com/watch?v=7D0vUEDSwXo
May 12, 2013 - Uploaded by Robert DIY Replaced the crank sensor on this 2003 Jeep Grand Cherokee.... to replace my crankshaft position sensor on my 1998 grand cherokee laredo.

Jeep Crankshaft Position Sensor Replacement (CKP, CKPS ...

? 4:07
www.youtube.com/watch?v=1Ho5iAKQV00

Oct 27, 2013 - Uploaded by WeekendHandymen
hi , do you think if I replace crank sensor will solve the problem ,my jeep .... Where's the crankshaft located in 99 jeep grand Cherokee laredo .

Transmission sticks in reverse- won't go into park. - JeepsUnlimited

www.jeepsunlimited.com/forums/showthread.php?...won-t-go-into-park
Jun 14, 2013 - 12 posts - ‎5 authors 2003 6 cyl 4x4 Grand Cherokee Laredo automatic- Occaionally, when shifting from REVERSE TO PARK, my Jeep will stay in reverse. Typically its ... '2001 WJ'4,0L'42RE'NV 242'380000 km'ECE Compliant' ??????????? ??? ...

2001 jeep grand Cherokee laredo - CarGurus

www.cargurus.com > Questions > Jeep > Grand Cherokee
CarGurusJan 27, 2014 - 2001 jeep grand Cherokee laredo - Just purchased a 2001 Jeep GrandCherokee Laredo and ... It starts in PARK sometimes and sometimes it won't and I have to start it in Neutral. ... Hatch shuts flush, but won't stay shut. help!

Instructions

1. Programming the First Transmitter
   • 1

     Unlock all of the Jeep Grand Cherokee's doors and open the driver's side door. Keeping the door open, lock it using the manual lock on the door itself.
     

   • 2

     Put the manual key into the ignition and switch it to the "On" or "Run" position, whichever applicable, without starting the engine.
     

   • Sponsored Links
     

     • Remote Control Software

       Control any distant PC remotely. Test the Software now for Free!
       www.TeamViewer.com/Remote_Control

   • 3

     Point the remote at the receiver (located by the little bulb on the car ceiling) and hold down the "Lock" button for up to 5 seconds.
     

   • 4

     When the driver's side door unlocks, you know the remote has been programmed correctly. If you are only programming one remote, jump to the next step. If not, manually re-lock the driver's side door and repeat steps 5 and 6 using each remote you would like to program and then continue.
     

   • 5

     Turn the key to the "Off" position and turn the ignition on immediately. This must be done within 20 seconds of programming the last remote. You're finished!
     

Sponsored Links

Read more: How to Program the Remote on a 1996 Jeep Grand Cherokee ' eHow.com http://www.ehow.com/how_7433787_program-1996-jeep-grand-cherokee.html#ixzz2KdCc5PQq

check all your fuses

Definitely, you'll have to take a look to see if any obstruction is visible. To check the fuses first you'll need to find them. The fuse block cover should illustrate what each fuse is for. You can visibly check the fuses, with a flashlight. Just take a look at the sunroof fuse and check that its not burned. That the metal inside goes from one side to the other and its not burned or broken. You can use a test light or a multimeter, a test-light will do. I usually check them visibly, its obvious when you have a blown fuse just by looking at it. Its better just to pull out the suspected fuse to check it.

disconnect battery

Throttle Positioning Sensor About 45 dollars and 3 mins to change. Its by the throttle body. JULES

There is a broken wire in the rubber casing between the door and the vehicle. Take the rubber casing off and you will more than likely find a broken wire or one about to break. Been there and done that.

try gently rocking wheel back an forth while wiggling the key

It's behind the passenger headlight.Need to take off grill,bumper fascia to get access to it.Mine took about an hour alltogether.