Question about 1995 GMC Sierra C1500

1 Answer

Tail lights don't work right on my 1995 gmc pick up all lights work in reverse no hazard lights no left turn signal right turn signal works right side brake light comes on when you turn on the cruise control when cruise control switch is on off no tail lights at all just head lights

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 44 Answers

Put you a couple of more body grounds on it if that helps From the Block to the fender and from the frame to the body

Posted on Mar 03, 2018

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 324 Answers

SOURCE: 97 BLAZER BRAKE AND HAZARD LIGHTS DON'T WORK

did you check the fuses?

If so, then check the plug on the steering column....

Posted on Nov 26, 2008

dtrannyman

  • 158 Answers

SOURCE: no reverse after rebuild on 4L60E Transmission from 1995 GMC Sono

There isn't a modulator on this trans as it is electronic

You can have first gear going forwrd but no reverse. It is possible. The low/ reverse clutch isn't needed to go forward.

Posted on Apr 02, 2009

joecoolvette

joecoolvette

  • 5660 Answers

SOURCE: no brake/hazard lights,have running/turn signal lights

Suggest you change hazard flasher 'can' first, then go to the hazard switch. I'm betting it's the flasher can.

Posted on May 11, 2009

Anonymous

  • 15 Answers

SOURCE: No turn signals, hazards or brake lights

replace the turn signal switch in the steering column

Posted on May 16, 2009

Anonymous

  • 5 Answers

SOURCE: checked all fuses-good, swapped bulbs-good, hazard

Does the turn signals or hazards work in the rear?? Yes... it may be the brake switch or the turn signal switch (power goes from battery, to the brake switch then to the turn signal switch, then to the lights. No? .. again.. possibly turn signal switch or the wiring between cab and bed.

Posted on Jun 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1977 GMC crew cab 3/4 ton V8 turn signal problem.


My friend is a part time mechanic he gets his solutions
from www.reliable-store.com
he gets from their every single detailed info, instructions etc. on all vehicles, and manuals like service, repairs, parts, owner's, operations, maintenance etc.
U can get help from there
there is a girl at chat she can help you

Mar 20, 2018 | GMC Cars & Trucks

1 Answer

How to repair not working rear lights 1997 gmc jimmy


brake lights not working - 1997 GMC Jimmy - RepairPal

repairpal.com > Questions > GMC > Jimmy > 1997 GMC Jimmy
Jan 11, 2011 - hi about 2 days ago i realized my brake lights were not working but my turn signal lights were working and parking lights as well but no brake ...

Tail Lights don't work but third brake light does, not fuses ...

answers.edmunds.com > Edmunds Answers
Sep 23, 2009 - 97 GMC Jimmy 4x4 blinkers work, reverse lights work, above window ... I just lost hazard lights and rear brake lights, they were working 2 days ... If it is a frayed wire or solder point, then you can repair it, but not any worn contacts. ... Does anyone have any suggestions on 1997 Honda Accord tail & brake lig.

Nov 19, 2015 | GMC Cars & Trucks

1 Answer

Turn signals, brake lights, reverse lights all blinking when turn signal is activated


The right tail light assembly is not grounding the chassis. Pull the access panel off and look for the ground points from the wiring harness and the assembly. Undo the nuts a bit and tighten them again. That should restore the ground and clear the problem.

Feb 22, 2015 | Subaru Forester Cars & Trucks

1 Answer

My dashboard and rear lights don't work


Assuming this has the V6, the 15A PARK LPS fuse in the underhood fuse block feeds constant power to the auto park lamp relay. When the relay closes, 12V power passes through the 10A INST LPS fuse in the right instrument panel fuse block to the panel dimmer switch and then to the five instrument cluster lamps.

If by "rear lights" you mean everything in the rear lamp assemblies, power for the tail lights (running lights) starts at the 15A PARKLAMP fuse in the underhood junction block, passes through the automatic lamp control (ALC) relay and the right instrument panel junction block to the tail filament of the dual stop/tail lamp and the separate tail lamp on each side. The 12 V power for the stop lamps is protected by the 20A STOPLAMPS fuse in the left I/P junction block, passes through the stoplamp switch when brakes are applied, stop filament of the dual stop/tail lamps. That leaves the turn signals and the hazard lamps. Power for the turn signals originates at the 10A TURNLAMPS fuse in the left I/P junction block and is applied to the hazard switch. Switch output goes to the turn/headlamp/wiper switch for selection of left or right turn signals. That switch output goes to the turn lamp. Power for the hazard function begins at the 10A HAZRD LPS fuse in the left I/P junction box and goes to the hazard switch. Switch output is sent to the left I/P junction box to make the turn signals flash. That's it. Post a comment if you need more information.

Sep 15, 2012 | 2002 Oldsmobile Alero

2 Answers

I have a 1995 GMC Sierra pickup and my tail lights don't work


there is a big green fuse in the fuse box under the hood. cost about 6 bucks. replace that

Jan 30, 2012 | 1995 GMC Sierra

1 Answer

Where is the exact location of the hazard light flasher for a 1989 GMC Sierra C2500, and what is the possibility that it is the true problem behind the hazards not working? Beyond my hazards not working my...


Are you sure the right side bulbs all flash? You say you replaced all the bulbs? Why would you replace bulbs that were working? Did you have this problem before you replaced the bulbs, or after. The hazard flasher is down under the dash, left side, turn the signals on and follow the clicking noise.The hazard flasher and the turn signal flasher should be near each other, and are interchangeable. If it clicks fast, a bulb or a bad socket is usually the cause. These trucks have a lot of problems with the tail light circuit boards.

Nov 04, 2009 | 1989 GMC C2500

1 Answer

Left side brake and hazard lights don"t work


sounds like a bad turn signal switch, wiggle it , just a little bit,... see if some of the lights start to work. do your turn lights work correctly??

Dec 02, 2008 | 2000 Chevrolet Lumina

Not finding what you are looking for?
1995 GMC Sierra C1500 Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...