2000 Ford Ranger SuperCab Logo
Walter Douthat Posted on Feb 19, 2011

2000 Ford Ranger 4.0L V6 - Engine died while driving, tried to restart but get nothing (cranks but doesn't seem to fire), had coil pack checked (good), can hear fuel pump run, pulled plug to check for spark and got nothing (plug was wet from gas), replaced crankshaft position sensor, still nothing.

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

  • Contributor 1 Answer
  • Posted on Feb 21, 2011
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Joined: Feb 21, 2011
Answers
1
Questions
1
Helped
587
Points
1

Check all fuses, any ground cables disconnected?

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

Will a 3.0 V6 out of a 2003 Ranger swap into a 2002 Escape with a 3.0 V6

you could use it but i think it may need all the parts swopping over ,check where crank sensor is as it may be you will need to change the flywheel .
0helpful
1answer

Both coils do not fire on 1 and 4. Will start but only running on 2 cylinders. Could both coils be bad or should I look elsewhere?

Part 3 -How to Test the Ignition Module and Crank Sensor ...

easyautodiagnostics.com > Ford > 2.3L
Mar 1, 2012 - Spark plugs for cylinders #2 and #3 get spark at the exact same time. ...voltage -12 Volts) to both individual ignition coils within the coil pack. ... Ford Mustang or Ranger (or 2.3L Mazda B2300), this is what you'll need ... for this 'Switching Signal' at the coil pack... but you can also test this ... 1991, 1992, 1993.

How to Diagnose a Misfiring Cylinder (2.3L Ford Ranger ...

troubleshootmyvehicle.com > Ford > 2.3L
Apr 3, 2012 - Bad Fuel Injectors can cause a Misfire Condition. ... the ignition system on the 2.3L Ford Mustang or Ranger consists of 2 ignition coil packs, ...

2002 ranger misfire rough idle - Discussion on Topix

www.topix.com > Ford Ranger
Jul 27, 2007 - My truck is giving the code misfire in number 4 cyl. I replaced my spark plugs, Wires, Coil packs (both of them) and all my fuil ... three (3.0L v6) go bad, the fuel/air mixture gets messed up. Judged: 2. 2 ... My truck runs rough only at idle. ...code for ford ranger 2002, 2.3 5speed. truck runs like a champ but that ...

Extremely stumped! I need the best and brightest 1994 Ford ...

answers.edmunds.com > Edmunds Answers
0helpful
1answer

What causes engine to ABRUPTLY shut off while driving ?

2004 Ford Explorer Engine Stalls/Cuts Out While Driving: 31 ...

www.carcomplaints.com/Ford/Explorer/.../engine/engine_stalls_cuts_out...
... 2013 · 2012 · 2011 · 2010 · 2009 · 2008 · 2007 · 2006 · 2005 · 2003 · 2002 · 2001 · 2000 ... 2004 Ford Explorer engine problems: engine stalls/cuts out while driving ...to overheat and slide out of its socket, causing the engine to shut off. ..... Suddenlyat 30-35mph, my engine just died and i cannot control the steering wheel.

2005 Ford Escape Engine Shutdown While Driving: 24 ...

www.carcomplaints.com/Ford/.../engine/engine_shutdown_while_drivin...
The 2005 Ford Escape has 24 complaints for engine shutdown while driving. ...January 22: Ford Ranger Driver Killed by Takata Airbag in South Carolina news ' 2 days ago; Ford Focus Door Latch ..... I was 80 miles from home when the engine shut off. .... No one could seem to determine the true cause of the problems.

Ford Ranger Stalling/Dying Problems - Edmunds.com

forums.edmunds.com > Ford > Ford Ranger

Nov 2, 2007 - 31 posts - ‎21 authors
Learn more about Ford Ranger at the Edmunds.com Car Forums! ... cut off a couple of times then it started happening more frequent while driving. ..... the other day I was driving down the highway and it just shut off, no warning .... 2000. when it gets overheated the circuit shorts and causes the engine to die. Ford Expedition engine cutting off while driving
31 posts
Oct 24, 2009
Mercury Mountaineer Start Stall Idle Problems
31 posts
Oct 1, 2007
More results from forums.edmunds.com
1helpful
1answer

Truck not firing properly front coil pack not firing at all.

if this truck has an o2 sensor i would replace that and also make sure the cat-converter is not plugged,this would give you your powerloss and egr code,next is your coil,this may be caused by the computer or your crank sensor,look at the tone ring that the crank sensor uses and make sure its not missing teeth or broken,also check all your fuses.
1helpful
1answer

My 3.0 ranger cranks but will not start is not getting fire to plugs changed coil pack cps crank senser what else could it be

Sounds to me like a bad control module. The control module controls the order of which the coil pack fires. If that is bad you get no spark. Seems to me that it should have been your second option right after replacing the coil pack.
1helpful
1answer

Misfire on number 2 cyl

Cylinders are numbered from front to rear (grille to firewall) passenger side: 1-2-3, driver's side: 4-5-6. Firing order is 1-4-2-5-3-6
Did you check by pulling #2 out while the engine is in idle to see no weakness from the engine? BTW your coil pack cost $80.

0helpful
1answer

2000 Pasat Engine Cranks but No Fire

likely crank shaft sensor ,maybe fuel pump or cam shaft sensor ,ignition module under coil pack,check your codes as your first effort in this,
0helpful
1answer

1987 Ford Ranger. Won't fire.

Ignition module comes to mind. If you've tested for spark (holding spark plug wire near the block when cranking) and the cap and rotor are good, it seems the module is the only other area left to try. Best of luck Patrick. Please post back with any other questions.
Greg
Not finding what you are looking for?

597 views

Ask a Question

Usually answered in minutes!

Top Ford Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...