My windshield wipers quit working. getting juice to one of the 3 wires.

Switch is bad.

When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Schematic Reference: Wiper/Washer Schematics


1

Did you review the Wiper/Washer System Description and Operation and perform the necessary inspections?
Go to Step 2
Go to Symptoms - Wiper/Washer Systems

2

1. Turn the ignition ON.
2. Turn the windshield wiper/washer switch OFF.

Are the windshield wipers always on?
Go to Step 3
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

3

Disconnect the windshield wiper/washer switch connector.
Are the windshield wipers always on?
Go to Step 4 if yes
Go to Step 7 if no

4

1. Disconnect the windshield wiper motor connector.
2. Test the windshield wiper switch signal 1 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?
Go to Step 11
Go to Step 5

5

Test the windshield wiper switch signal 2 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 6

6

Test the windshield wiper motor high speed circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 9

7

Inspect for poor connections at the windshield wiper/washer switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 8

8

Replace the windshield wiper/washer switch. Refer to Windshield Wiper and Washer Switch Replacement - On Vehicle in Steering Wheel and Column.
Is the repair complete?
Go to Step 11
--

9

Inspect for poor connections at the windshield wiper motor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 10

10

Replace the windshield wiper motor. Refer to Windshield Wiper Motor Replacement .
Is the repair complete?
Go to Step 11
--

11

Operate the system in order to verify the repair.
Did you correct the condition?
The Wiper / Washer System consists of the following components:
?€¢
Windshield wiper / washer switch

?€¢
Windshield wiper system module / motor

?€¢
Windshield washer fluid pump

?€¢
Windshield washer fluid level switch

?€¢
Instrument panel cluster (IPC)

?€¢
ACC 15-amp fuse

?€¢
WSW 30-amp fuse

Clean washer pump connector with de ox-it or replace connector , clean corrosion

unplug the wire at the wiper motor and then turn the key on and then turn the wiper switch on and test the wires at the plug with a 12 volt tester . if u dont have any thing then ur wiper switch is bad , if u have juice at the plug then it sounds like its the motor.

Check fuse #9 in the rear fuse panel.

The wiper linkage is either broken, or has become un-attached...You will need to remove the wiper arms and plastic shroud above the linkage to inspect...When re-assembling be sure to have the wipers turned off, and in the down position...when mounting the arms back onto the spindles...Hope this helps.

It could be as simple as a blown fuse. Other problems involve wiring, switch, wiper motor. It needs to be checked by someone who understands wiring diagrams and follows it. Good luck!!!

It sounds like your wiper motor is dying

YOUR WIPER MOTOR COULD HAVE BINDING LINKAGE AND PIVOTS.TRY LUBRICATE THEM WITH WD40.TRY NOT TO GET ANY ON WINDSHIELD.IF THIS DONT WORK WIPER MOTOR COULD BE FAULTY.

First check the fuse, if the fuse is good check to see if you are getting power at the wiper motor. Power at the motor means bad motor, no power is either the switch or wiring.