Cars & Trucks Logo

Related Topics:

Anonymous Posted on Mar 29, 2011

Stay is broken / missing. what would it need to look like if I was to make a new one. Or are they avaiable.

1 Answer

ojohanson

Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

New Friend:

An expert that has 1 follower.

Hot-Shot:

An expert who has answered 20 questions.

  • Expert 48 Answers
  • Posted on Mar 29, 2011
ojohanson
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

New Friend:

An expert that has 1 follower.

Hot-Shot:

An expert who has answered 20 questions.

Joined: Mar 19, 2011
Answers
48
Questions
0
Helped
10870
Points
118
  • Anonymous Mar 29, 2011

    dodge ram D250 van - rear door has a missing strap? to stop door from over opening (so it will not open to far and damage the tail lights.) need to know what its called and how I can get replacement.

×

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer
1helpful
1answer

ABS AND BRAKE LIGHTS

It could be a number of things including the ABS fuses, ABS pump, a bad wheel speed sensor or broken/missing teeth that the sensors use to calculate wheel speed. You would need to take it somewhere and get the DTC's (Diagnostic Trouble Codes) with a scan tool to proceed any further.
0helpful
1answer

97blazer 4x4, I had codes for miss fire cylinder #5, I've replaced my fuel spider, mass air censor, complete tune up,

Check for a broken hose at the pcv valve and make sure the plug did not get dropped while tring to install also you can swap the plug with another one or with another cylinder and see if the miss follows the plug or stays with #5 if it stays with 5 a compression check and a leak down test will most likely tell if there are any other problems
0helpful
1answer

My 2000 mustang convertible lh interior door window switch insert panel has come off. End piece seems to be broken off. Top has plastic tab that snaps into door panel, but won't stay in. Is there a clip...

You need to order a new part if you're missing the parts that broke off. There's been some success using epoxy to repair but that's usually a short term fix.
The part is easy to find either at a salvage yard, eabay, or online places lie CJ Pony parts.
0helpful
1answer

My saturns e-brake stoped working and wont stay up how can i fix that?

if you mean the parking brake, sounds like you have broken a cable. the cables keep tension on the handle and without that tension it won't stay up. also the broken cable would mean no parking brakes. if however the parking brakes work when you pull and hold the brake handle, then you have a broken part in the handle itself. you will need to get under it to figure out which cable is broken and replace it. the heat shielding may make this hard. I think the parking brake system is made of three separate cables, you can buy new ones at autozone, advance, ebay. stay away from dealers and used parts on this repair.
0helpful
1answer

Passenger side mirror with HD gas light. Mirror popped out. Everything is still in tack and working. Can it be put back in place without buying new one.

look at the back side there is a circle of little teeth if some of them are broken and or missing you need a new replacement mirror,not the whole mechanical partthat bolts to the door.if no teeth are broken or missing then press the mirror back in place with the palm of your hand.carefully it can crack.hope this helped.
2helpful
2answers

1993 buick untra runs rough

you need new engine oil in the car... and air filter
0helpful
1answer

Horn does not work, replaced 20amp fuse that looked broken, still not working, would it be more than the fuse. I only thought it would be the fuse because when you test the horn there is clicking sound...

If you can hear the relay clicking then the fuse is not blown and the horn button is working. The horn itself is bad or has a bad ground. My guess is you need a new horn. klaxon horns rust on the inside and at some point quit working. Buy a universal replacement as original GM horns are very expensive.
0helpful
1answer

Clutch pedal stays on floor when released

check the helper spring on the clutch pedal. You'll have to get down in the driver's footwell and using a flashlight look at the mechanism while you push the pedal down (and pull up). If the spring isn't missing or broken and everything looks okay, then change the clutch master cylinder. The piston in the cylinder is probably binding due to corrosion in the bore. I have an 1986 and had the same problem. Changing the clutch master cylinder fixed it.
Not finding what you are looking for?

30 views

Ask a Question

Usually answered in minutes!

Top Dodge Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...