2002 Ford Taurus Logo

Related Topics:

Posted on Mar 30, 2017
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

I have replaced the coil pack on my 2002 ford taurus with the 3.0 24 valve engine. I have no spark to cyliders 3 and 4. I have also replaced the electical connector to the coil pack as well. All 4 wires have power and the yellow and white and the yellow and black pulse with the test light, the yellow and red and the solid red wire have a steady light with no pulse. Do you have any suggestions please. I have also checked all grounds and they seem to be fine. Do also take into consideration that the motor was changed 1 and a half years ago but the car run fine when changed and the car has been sitting for at least a year now. When started up this is what was happening. Thank you, Kenny

1 Answer

Jeff Armer

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

  • Ford Master 15,575 Answers
  • Posted on Mar 30, 2017
Jeff Armer
Ford Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Joined: Nov 22, 2012
Answers
15575
Questions
1
Helped
7103601
Points
73899

All 4 wires have power and the yellow and white and the yellow and black pulse with the test light, the yellow and red and the solid red wire have a steady light with no pulse. The PCM - engine computer is no good , driver (transistor's) in side turn the coil on an off . Burnt transistors .

5 Related Answers

ANDY PLUMB

  • 150 Answers
  • Posted on Mar 04, 2009

SOURCE: rough running, erratic spark

Run a compression test on the cylinders.If reading is low on any drop a little engine oil into the pot. If compression rises you have compession ring problems. Remove all plugs before you try this and place leads away from engine.

Ad

Anonymous

  • 145 Answers
  • Posted on May 26, 2009

SOURCE: 99 Ranger- Consistant coil pack issues....

What is the engine size? Have you checked the ignition module? Check the output of the crank sensor at the ignition module to verify wiring integrity. The signal is shielded so insure there is no break in the insulation.

Anonymous

  • 57 Answers
  • Posted on Jun 14, 2009

SOURCE: My 2002 Ford Taurus will shutter and die when

the idle air control valve is responsible for engine idle.
this is a common failure on ford's. but I don't think yours is bad because it does idle high befor it dies.
you stated you had codes p0171 and p0174 these are lean codes for bank one and two, you said you found a vacuum leak and repaired it, the vacuum leak was mostly likely the cause of the lean codes, however the pcm has calibrated the fueling stategy for this lean mixture, what you need to do is erase the KAM "keep alive memory" this is done by unhooking the negative battery cable for 60 seconds, this is the only way to erase the KAM the $6000.00 machine I use wont even do it.

once the KAM is clean the computer will go into a relearn state and all operating values will be adjusted for the vehicles current condition, during this relearn session the vehicle may have some driveability issues (low or high idle, stalling, poor fuel economy) the relearn should complete within 10 minutes of idling and then 10 minutes of driving.

good luck and keep me updated

[email protected]

Anonymous

  • 1615 Answers
  • Posted on Sep 07, 2009

SOURCE: 2002 ford taurus almost seems like its missing when driving,idle.

You will need to do a running compression test. Sounds like you have ring issues. Too much blow by causing excessive crankcase pressure. Also pull the dipstick. Put your finger over the hole with the engine running. It should be pretty nuetral in pressure. If you have vacuum you have an intake leak. If it blows pressure you have an engine issue.

johnjohn2

Johnny Brown

  • 5763 Answers
  • Posted on Jun 12, 2010

SOURCE: Truck not firing properly front coil pack not firing at all.

if this truck has an o2 sensor i would replace that and also make sure the cat-converter is not plugged,this would give you your powerloss and egr code,next is your coil,this may be caused by the computer or your crank sensor,look at the tone ring that the crank sensor uses and make sure its not missing teeth or broken,also check all your fuses.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
2answers

2002 ford taurus missfire or vibrate @ 3000 rpm what could possible be the problem? no check engine lights on

Do you have a check engine light that is flashing, if it is you need to have the fault codes checked with a scan tool to see what is causing this.
0helpful
3answers
0helpful
1answer
0helpful
2answers

I have a 2002 ford taurus SE, coil pack has been replaced because Advanced Auto ran a diagnostic and said my coil pack was bad. Well its not and im still not getting fire on #3 and #4 spark plugs. changed...

You visually checked for spark and there was none? #3 and #4 show to be on same coil, each coil fires two plugs. Battery has a full charge? The red wire at coil pack is voltage, it has good voltage? Any applicable trouble codes?
The yellow wires with different tracer colors are grounds controlled by the pcm, one ground for each coil. Did you check voltage on ground wire engine cranking? I can't rule out a faulty coil driver in pcm. It's possible your old coil pack damaged the coil driver in pcm? If that is the problem, hope it didn't hurt the new coil pack.
ignition coil-rpv3jsqdi3m52f0zwyccrrib-3-0.jpg
1helpful
2answers

How do I replace the ignition coil in my 2002 ford taurus


Removal & Installation

3.0L (VIN S) Engine

  1. Disconnect the negative battery cable.
  2. Unplug the engine control sensor wiring connectors from the ignition coil and the radio ignition interference capacitor.
  3. Tag and disconnect the spark plug wires from the coil by squeezing the locking tabs, then twist the tab and pull upwards.
  4. Unfasten the four ignition coil retainers and remove the coil and the coil ground wire the radio ignition interference capacitor. Save the capacitor and coil ground wire for re-installation of the coil assembly.
  5. Wipe the coil towers with a clean cloth dampened with soap and water. Remove any soap film and dry with compressed air. Inspect the coil for cracks, carbon tracking, dirt or damage and replace as necessary.

    0996b43f802333d8.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Ignition coil assembly mounting-3.0L DOHC engines


To install:
  1. Place the coil, capacitor and the coil ground wire onto its mounting location on the right hand valve cover.
  2. Install the coil assembly retainers and tighten to 45-61 inch lbs. (5-7 Nm)..
  3. Apply dielectric compound D7AZ-19A331-A or its equivalent to the spark plug wire boots.
  4. Attach the spark plug wires to their proper terminals on the coil and make sure the boots are firmly seated so that the locking tabs engage.
  5. Attach the engine control wiring connectors to the ignition coil and the radio ignition interference capacitor.
  6. Connect the negative battery cable, start the vehicle and check for proper operation.
5helpful
2answers

2002 ford f150 4.2l wiring diagram

The COIL PACK TOWERS are numbered : coil----3---4 pack---2---6 plug----1---5 ----------------------------------------------------------------- The engine cylinders / spark plugs are numbered : passenger side , front to rear , 1 , 2 , 3 -----drivers side , front to rear , 4 , 5 , 6 ------------------------------------------------------------------- The spark plug firing order is ( 1 -4 - 2 - 5 - 3 - 6 )

0helpful
4answers

I have a 2000 Ford Taurus and it has been running rough for the last couple of months, but my obdII scanner reads nothing. Just this morning my check engine light came on so I put my scanner back on and it...

my taurus did not do this until i had over 124,000 miles you may have to replace all of the plugs and the wires and the fuel filter give this website a try www.taurusclub.com if all fails stop by your local library and get your hands on a Haynes auto repair manual for your car wish you the best of luck Michigan Man.
7helpful
2answers

2001 FORD TAURUS 24 VALVE DOHC MOTOR WILL NOT START

i have a 2001 taurus 24valve dohc 3.0 engne i have a bad coil pack what steps do i need to do to change the coil pack
Not finding what you are looking for?

261 views

Ask a Question

Usually answered in minutes!

Top Ford Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...