Question about 1999 Ford Ranger SuperCab

1 Answer

Need timing marks for a 1999 ford ranger - 1999 Ford Ranger SuperCab

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 1,940 Answers

Align the timing marks:

  • Align the crankshaft sprocket mark to the front cover notch.
  • Align the oil pump sprocket diamond to the engine front cover diamond.
  • Align the camshaft sprocket triangle to the engine front cover triangle.
need timing marks for a 1999 ford ranger - pctech1_11.gif

Here are the Timing Procedures from the service manual:
Click Here

I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514

Posted on Apr 13, 2011

  • Thomas Smithbrother Jul 03, 2014

    www.youtube.com/watch?v=MQDAhLS-NAQ

×

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
melvi_99

Levi Casaol

  • 387 Answers

SOURCE: Need timing marks (diagram) on a 1998 ford ranger

gm/ford69752b6.jpg

Posted on Jun 22, 2010

Anonymous

  • 172 Answers

SOURCE: Timing marks on 1999 Ford Ranger 2.5L.

Rotate the engine so that No. 1 cylinder is at TDC on the compression stroke. Check that the timing marks are aligned on the camshaft and crankshaft pulleys. An access plug is provided in the cam belt cover so that the camshaft timing can be checked without removal of the cover or any other parts. Set the crankshaft to TDC by aligning the timing mark on the crank pulley with the TDC mark on the belt cover. Look through the access hole in the belt cover to make sure that the timing mark on the cam drive sprocket is lined up with the pointer on the inner belt cover.

  1. Loosen the alternator retaining bolts and remove the drive belt from the pulleys. Remove the water pump pulley.
  2. Loosen and position the power steering pump mounting bracket and position it aside.
  3. Remove the four timing belt outer cover retaining bolts and remove the cover. Remove the crankshaft pulley and belt guide.
  4. Loosen the belt tensioner pulley assembly, then position a camshaft belt adjuster tool (T74P-6254-A or equivalent) on the tension spring rollpin and retract the belt tensioner away from the timing belt. Tighten the adjustment bolt to lock the tensioner in the retracted position.
  5. Remove the timing belt.

To install:
  1. Install the new belt over the crankshaft sprocket and then counterclockwise over the auxiliary and camshaft sprockets, making sure the lugs on the belt properly engage the sprocket teeth on the pulleys. Be careful not to rotate the pulleys when installing the belt.
  2. Release the timing belt tensioner pulley, allowing the tensioner to take up the belt slack. If the spring does not have enough tension to move the roller against the belt (belt hangs loose), it might be necessary to manually push the roller against the belt and tighten the bolt.

The spring cannot be used to set belt tension; a wrench must be used on the tensioner assembly.
  1. Rotate the crankshaft two complete turns by hand (in the normal direction of rotation) to remove the slack from the belt, then tighten the tensioner adjustment and pivot bolts to specifications. Refer to the necessary illustrations. Make sure the belt is seated properly on the pulleys and that the timing marks are still in alignment when No. 1 cylinder is again at TDC/compression.
  2. Install the crankshaft pulley and belt guide.
  3. Install the timing belt cover.
  4. Install the water pump pulley and fan blades. Install upper radiator hose if necessary. Refill the cooling system.
  5. Position the alternator and drive belts, then adjust and tighten it to specifications.
  6. Start the engine and check the ignition timing. Adjust the timing, if necessary.

Posted on Nov 25, 2009

Louie_3006

Jonathan Suttles

  • 79 Answers

SOURCE: need timing marks ford ranger

The timing marks are on your timing belt cover. There is a little circle on the bottom right of the cover near the harmonic balancer that you can pop out to see if your distributor accesory gear is in the correct position. The camshaft has a triangle on the inside of the gear that you can line up with this accesory gear. The bottom of the timing belt cover has your timing tick marks and you may have to clean off this rectangular piece that is sticking out on the cover to see the marks. A good timing gun and remembering where the number 1 cylinder on your distributor is a good start to timing your motor. Refer to a Haynes Manual and it will give you a good guide line on how to time your motor with TDC. I hope you have good luck with this!

Posted on May 18, 2009

Patrick Rayome

  • 1757 Answers

SOURCE: what do the timing belt marks line up on a 94 ford

My apologies for the delayed response. I am going back to answer unanswered questions.
CLICK
on the following LINK. It has the Timing Belt & Mark(s) Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my sincerest apologies...
Thanks!

http://www.2carpros.com/car_repair_information/year/1994/make/ford/model/ranger/1994_ford_ranger_timing_belt_diagram_marks.htm

Posted on Mar 03, 2010

wfservices

Wayne Fellows

  • 262 Answers

SOURCE: I need the timing marks for a 1999 ford escort ZX2

NOTE: Make sure the correct (second) notch in the pulley is indexed to the lower cylinder block (6010).
Position the crankshaft (6303) just prior to top dead center. Install the Camshaft Alignment Timing Tool on the back of the camshafts. fcdabeb.gif

  1. NOTE: Make sure the correct (second) notch in the pulley is indexed to the lower cylinder block (6010).
    Position the crankshaft (6303) just prior to top dead center.

2.Remove the bolt and install the top dead center timing peg
3 Rotate the crankshaft clockwise against the peg.
5332a96.gif NOTE: Installation of the alignment tool into the exhaust camshaft (6250) may require the camshaft to be rotated clockwise.
Install the Camshaft Alignment Timing Tool on the back of the camshafts. 9e76853.gif
  1. Install the intake timing sprocket and loosely install the bolt.
  1. Rotate the oil control bushing one full turn and inspect for binding. Position the bushing with the single hole in the 12 o'clock position.
  2. f7eb1fd.gif
    1. Install a new exhaust sprocket O-ring into the exhaust sprocket.
    1. Install the exhaust camshaft sprocket. Make sure that the tab on the sprocket engages the hole previously positioned at 12 o'clock in the oil control solenoid bushing.
      • Loosely install the bolt.
      • 73bc433.gif
    1. Loosely install the timing chain tensioner.
    1. Install the timing belt.
    2. 9406c65.gifEngage the timing belt tensioner tab into the upper timing cover backplate. a1cb4c6.gif
      Using a 6 mm Allen wrench, adjust the timing belt tensioner until the index marks are aligned. Tighten the bolt
    809c9dc.gif
    1. sxf~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: The camshaft must be held stationary with an open-end wrench. Do not use the alignment tool to hold the camshaft in position or damage to the camshaft may occur.
      Tighten the bolt on the intake camshaft sprocket.
    2. 25f34cb.gif
    1. sxf~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: The camshaft must be held stationary with an open-end wrench. Do not use the alignment tool to hold the camshaft in position or damage to the camshaft may occur.
      Tighten the bolt on the exhaust camshaft sprocket in three steps.
      • Tighten the bolt to 50 Nm (36 lb-ft).
      • Remove the TDC peg and Camshaft Alignment Timing Tool.
      • Tighten the bolt to 115-125 Nm (85-92 lb-ft).
      • 24c43e7.gif
      Install the VCT oil plug.c96f65a.gif
    1. NOTE: Make sure the correct (second) notch in the pulley is indexed to the lower cylinder block.
      Position the crankshaft just prior to top dead center.
    2. 993d4ea.gifRemove the bolt and install the TDC peg. Rotate the crankshaft clockwise against the peg. NOTE: Installation of the alignment tool into the exhaust camshaft may require the camshaft to be rotated clockwise. If the alignment tool does not align and install in the camshafts, repeat Steps 1 through 17.
      Install the Camshaft Alignment Timing Tool on the back of the camshafts.
      1. Remove the alignment tool and TDC timing peg.
      1. Install the bolt. 5332a96.gif

    Posted on Mar 14, 2010

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    2.5 ranger td 2007 diesel pump timing marks n will da key way on the pump should b same as the timing marks


    images for 2.5 ranger td 2007 diesel pump timing marks

    Ford ranger 2.5 diesel pump timing marks - Fixya

    www.fixya.com/.../t12609400-ford_ranger_2_5_diesel_pump_timing_...
    Apr 29, 2012 - SOURCE: need the timing marks for a 3.1 td 5 cyl diesel injectionpump. isusu engine?? have you looked for a 8mm hole in timing gear that ...

    Mazda Bravo 2.5 TD 2000 - YouTube

    ? 10:00
    https://www.youtube.com/watch?v=D8zJeouIXfo
    Sep 11, 2010 - Uploaded by V8Jagnut
    and one other , would a miss timing on the fuel pump cause engine .... The only thing I've ever seen with a Mazda dieselengine was an old Mercury Lynx. ... Ford Ranger Mazda B25002.5TD Servicing Guide Part 2 - Air and .

    Oct 29, 2015 | 2006 Ford Ranger

    2 Answers

    Why doesn't My truck start after changing the Timing belt on My 1999 Ford Ranger?


    you need to pull the timing back apart pull the number one spark plug and role the motor over by hand to top dead center on the compression stroke the the mark for the crank should be lined up or almost lined up line it up perfect on its mark then set the cam to its mark install belt role over by hand 2to4 full rotation marks should line up perfect . install crank pulley fire it up for a split second shut it off and put it all back together

    May 25, 2014 | 1999 Ford Ranger SuperCab

    1 Answer

    I have done an engine overhaul and need to assemble it back so I am looking for engine timing marks for a Ford Ranger 2.5 D engine a 1999 model.


    How did you do the rest of the "overhaul" without knowing all engine specs? Crank at TDC, oil pump at 12 o' clock, (diamond) cam gear is marked approx 5 o' clock (triangle) on plastic cover.

    Sep 15, 2011 | 2000 Ford Ranger SuperCab

    1 Answer

    1999 ford ranger timing marks 2.5


    One is on the crank shaft pully (for TDC). It is a line, scribed on the pully, that alligns to a pointer on the plastic timing belt cover. The second is on the cam shaft pully. It can be accessed by removing the rubber inspection plug on the timing belt cover. The third is on the auxillary shaft (oil pump) and is also accessed through an inspection plug on the timing belt cover.

    On the cam and oil pump pullies, the diamond aligns to the diamond and the triangle aligns to the triangle (the pullies have both). These should be perfectly aligned when the crankshaft pully line is at 0 deg TDC. If you can't see the marks through the inspection port while the crank is at 0 TDC, you are 180 degrees out - turn the crank one more time. 

    Sep 12, 2010 | 1999 Ford Ranger SuperCab

    1 Answer

    How to replace timing belt on 1999 ford ranger with 2.5 engine


    take out the old belt by releasing the tension with the alternator, and then put on the new belt with the marks in place and tension it back as the old one

    Mar 13, 2010 | 1999 Ford Ranger SuperCab

    1 Answer

    Camshaft timing mark crankshaft timing mark


    Belt covers need to be on. Timing mark on crankshaft (while on compression stroke) should line up with TDC mark on cover. then Camshaft mark, needs to line up by looking through access hole of cover, and align mark on cam sprocket with pointer on inside of belt cover.

    Oct 22, 2009 | 1987 Ford Ranger

    1 Answer

    Timing marks for 1999 ford ranger sport


    There likely isn't a timing adjustment. I believe those trucks don't have a conventional distributor and timing is controlled by the computer.

    Apr 10, 2009 | 1999 Ford Ranger SuperCab

    1 Answer

    Timing Marks-99 Ford Ranger


    Its Dot to Dot.. Crank Pointer Up.. CAm Pointer down.. DOT 2 DOT.. Thank you

    Mar 15, 2009 | 1999 Ford Ranger SuperCab

    Not finding what you are looking for?
    1999 Ford Ranger SuperCab Logo

    1,855 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    Marvin
    Marvin

    Level 3 Expert

    85222 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22485 Answers

    gerry bissi

    Level 3 Expert

    4388 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...