Hi, Sarel the vast majority of service, parts fiche, and owners manuals on the internet are "FREE" to download and all service manuals contain wiring diagrams in the back pages. The rest usually charge a modest fee of $15 and there is a handful of obscure, rare, obsolete, and very old models that are no longer or never were available and some were never printed in English. The Indian and Philippine markets are usually in E-book format only, for these rare occasions I shall look on eBay and find the cheapest one available. Most of the manuals will cover your exact make, model, and year otherwise one will be provided that comes as close as possible to your bike and will have most of the same info that an exact manual would have. If there is no $ sign after the manual link it is free to download.
To download your manual for viewing or printing please click on the blue links below. Good luck and have a wonderful day. Honda GoldWing GL1100 Service Manual https://www.partsfish.com/page/oem-parts-for-honda Honda Gold Wing GL1100 Owner Manual https://www.motorcyclespecs.co.za/model/Honda/honda_gl1100%20interstate.htm Honda Gold Wing
To set up an HP printer with a PC or adaptable phone, you charge a affairs through with the machines can communicate. Nonetheless, the cast has advised altered software/ app for altered devices 123 hp com setup. Thus if you would install a software disciplinarian on an adaptable phone, it will not work. On the contrary, installing the appropriate affairs will accord you a smoother experience.
your crank case oil lubricates all of your internals including your clutch pack! if your crankcase oil is full and you clutch doesn't work still drain you oil and remove the right side crankcase cover that is where your clutch pack resides remove the clutch basket and check the clutch pack plates for ware they may need replacement! Empty your gas tank and start with fresh gas good chance your carburetors are gummed up from stale gas which will make it run rough and usually loose the ability to idle! as for your font brake check to make sure the master cylinder for it is topped up with fluid is so try bleeding it if after bleeding the brakes no improvement is noticed remove the front brake assembly pull the pads off and check to see if there is any movement in the calipers themselves they may have seized from sitting! and there is no honda virago, virago is a yamaha and i think if u have an 82 xv its a yamaha virago
Hi, Tiny I feel your pain, before testing any electrical component in the Starter Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries. Depending on battery voltage starter relays and starter solenoids can make the same noise when you hit the starter button. You can easily determine which one is at fault by two simple tests:
STARTER RELAY- place your thumb and index finger on the starter relay and press the starter button, if you feel the click then the relay is faulty and needs to be replaced.
STARTER SOLENOID- bridge the positive and negative poles of the solenoid with a small screwdriver if you get a loud clunk then the solenoid needs to be rebuilt or replaced as necessary. If the engine turns over then replace the starter relay.
A motorcycle starter relay is an electronic mechanical switch that has a small coil winding around a piece of metal that requires low amperage and thin wires to be activated. When you turn on your ignition switch power 12 volts is sent to the relay coil which in turn becomes a magnetic contact point that pulls a spring-loaded contact point to itself completing an electrical circuit that allows more amperage necessary to be accessed by the starter solenoid which in turn acts in the same way as the relay but on a larger scale with its stronger heavier contacts making available the necessary amperage to turn the starter motor. If your battery has low voltage it, in turn, makes the magnetic contact point weak in trying to pull its counterpart to make a connection. These relays are usually encased in a plastic housing that is sealed, depending on the quality of the product. When activated they will produce a small amount of heat to their metal components which in turn can create the perfect environment for condensation to form depending on weather conditions and how careless you may be with a water hose or sprayer while washing your bike. After a period of time, several months to several years depending on the circumstances this condensation is the starter button for electrolysis and the slow build-up of corrosion which ends by preventing the magnetic contacts in making a solid connection and alerts you to this situation with the customary greeting "CLICK or BUZZ" if you get a single loud "CLUNK" then the starter solenoid is at fault and needs to be rebuilt or replaced as necessary. The relay is inexpensive and needs to be replaced however in a pinch they can be forcibly opened cleaned and resealed with silicone. In a nutshell, motorcycle starter relays take in low amperage and send out higher amperage when activated and for curious minds, the voltage remains constant at whatever your battery reads at the time.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day. https://www.reddit.com/r/scooters/comments/2zv9i2/honda_metropolitan_on_craigslist_clicks_but_wont/ https://www.youtube.com/watch?v=7o7HUitlpfE https://www.manualslib.com/manual/1434637/Honda-Metropolitan-Chf50.html https://www.partsfish.com/page/oem-parts-for-honda https://www.manualslib.com/manual/677660/Honda-2008-Metropolitan-Chf50.html
No, it's most likely a fuel related issue. First make sure you don't have the kill switch engaged.
Check the fuel filter and replace if old or dirty.
Then with the fuel petcock turned on open the drain screws on the carbs to be sure clean fuel flows from both of them. If it doesn't you have a blockage somewhere and disassembly of the fuel system and or carburetors may be called for. Start tracing the fuel path to see how far it is getting.You might have rust, water or other crud in your tank plugging things up.
ya gotta ask yourself WHY do I want to do that?
Even if it is possible, it is a giant leap backwards.
I will guess that it is not possible unless you want to build the parts required. But it may still not be possible.