Honda Motorcycles - Page 3 - Popular Questions, Answers, Tips & Manuals
We're does the hose on the bottom of the carburetor go on a 2007 honda crf 100
The hose on the bottom of the carburetor of a 2007 Honda CRF 100 should be connected to the carburetor overflow drain tube. The overflow drain tube is a small tube located on the bottom of the carburetor bowl. It is designed to allow excess fuel to drain from the bowl and prevent flooding of the carburetor.
To connect the hose to the overflow drain tube, first locate the tube on the bottom of the carburetor bowl. Next, slide the end of the hose onto the tube and secure it with a hose clamp if necessary. It is important to make sure the hose is securely attached to the drain tube to prevent fuel leakage.
2/25/2023 4:15:16 PM •
Honda...
•
178 views • 1 helpful votes
Honda CBR650. number of liters of fork oil please?
Question edited for clarity and add maker,
Question moved to model category.
Full service information here. It a mix or volume and then oil level.
https://www.bikesinfotech.com/fork-188.html
Pour the specified amount of recommended fork fluid into the fork tube.
RECOMMENDED FORK FLUID:
Honda Ultra Cushion Oil 10W or equivalent
FORK FLUID CAPACITY:
CBR650F/FA: 505 +- 2.5 cm3
(17.1 +- 0.08 US oz, 17.8 +- 0.09 Imp oz)
CB650F/FA: 482 +- 2.5 cm3
(16.3 +- 0.08 US oz, 17.0 +- 0.09 Imp oz)
Slowly pump the fork tube several times to remove any trapped air from the lower portion of the fork tube.
Compress the fork tube fully and measure the fluid level [1] from the top end of the fork tube.
[1] FLUID LEVEL:
CBR650F/FA: 140 mm (5.5 in)
CB650F/FA: 128 mm (5.0 in)
The 2018 Honda Grom CDI power wiring diagram
Here is a basic wiring diagram for the CDI power circuit on a 2018 Honda Grom:
- The CDI power wire is typically a red wire that runs from the ignition switch to the CDI unit.
- The ignition switch is usually located on the right side of the handlebar and has three wires connected to it: a red wire, a black wire, and a white wire.
- The red wire from the ignition switch connects to the red wire on the CDI unit.
- The black wire from the ignition switch is typically a ground wire that connects to the frame of the motorcycle.
- The white wire from the ignition switch is usually a power wire that supplies power to the headlight and other accessories.
- The CDI unit converts the power from the ignition switch into a high-voltage spark that ignites the fuel in the engine.
Note: This is a general wiring diagram and the wire colors and connections may vary depending on the specific model and year of the Honda Grom. It is important to refer to the owner's manual or a detailed wiring diagram specific to your motorcycle for accurate information. Additionally, modifying the electrical system of your motorcycle may void the warranty and could cause damage or injury if done improperly
1/22/2023 3:25:47 PM •
Honda...
•
226 views • 0 helpful votes
Remove mirror glass honda dn 01
Removing the mirror glass on the 2009 Honda DN-01 base model requires two steps. First, remove the plastic mirror cover by pushing it inward and up to remove it from its clips. Then, use a flathead screwdriver to gently pry around the outside edge of the mirror glass until it pops off of the mirror base.
2006 honda 350 es 4x4 4-wheeler
no info generic answer use these service manuals to assist in problem --------------------https://www.manualslib.com/products/Honda-Trx350fe-Fourtrax-350-4x4-Es-3561003.html----------------------https://www.manualslib.com/manual/804553/Honda-Trx350tm-Rancher.html
2/9/2023 10:39:17 PM •
Honda...
•
32 views • 0 helpful votes
Not finding what you are looking for?