Husaberg Fe 501 E - Popular Questions, Answers, Tips & Manuals - Page 7
Clutch
you need a micrometere or vernier caliper to measure how thick they are that how you tell how worn the clutch is. the manual will list the specificational limit (how thin you should allow them to get and how do the basket and innser hub looks like). if they have small teeth on them they are worn.,
Clutch
you need a micrometere or vernier caliper to measure how thick they are that how you tell how worn the clutch is. the manual will list the specificational limit (how thin you should allow them to get and how do the basket and innser hub looks like). if they have small teeth on them they are worn.,
Oil check
There are usually two methods to check the oil. One is a dipstick and the other is a sight-glass. You should have one or the other somewhere on the side of the engine crankcase. It should be fairly obvious and not require the removal of any body panels. If you can't find a dipstick in the side of the crankcase you will need to get down on your hands and knees and have a look for a sight-glass instead. This will be like a tiny window with a gauge against which you can check the level.
Clutch
you need a micrometere or vernier caliper to measure how thick they are that how you tell how worn the clutch is. the manual will list the specificational limit (how thin you should allow them to get and how do the basket and innser hub looks like). if they have small teeth on them they are worn.,
Clutch
you need a micrometere or vernier caliper to measure how thick they are that how you tell how worn the clutch is. the manual will list the specificational limit (how thin you should allow them to get and how do the basket and innser hub looks like). if they have small teeth on them they are worn.,
Oil filter
i always just put some on the o-ring before i put it back in
but no you dont need to have oil on it,
Oil check
There are usually two methods to check the oil. One is a dipstick and the other is a sight-glass. You should have one or the other somewhere on the side of the engine crankcase. It should be fairly obvious and not require the removal of any body panels. If you can't find a dipstick in the side of the crankcase you will need to get down on your hands and knees and have a look for a sight-glass instead. This will be like a tiny window with a gauge against which you can check the level.
Maintance
ProClean is good stuff but not worth the money. The only reason I had it was because I won a create of it at our clubs Supercross race it's too expensive in my opinion.
I buy 40 litre containers of stuff called TFR which stands for Traffic Film Remover, it basically is a detergent like ProClean, Simple Green and all the others, only it costs a fraction of the price and isn't deluted. This means you can delute it to your own strength for different causes. You can see it removing dirt as you watch, like someone said above. You can not use it pure on the bike however, it will make alloy parts go dull - as my buddy found out lol. ,,,
Maintenance
ProClean is good stuff but not worth the money. The only reason I had it was because I won a create of it at our clubs Supercross race it's too expensive in my opinion.
I buy 40 litre containers of stuff called TFR which stands for Traffic Film Remover, it basically is a detergent like ProClean, Simple Green and all the others, only it costs a fraction of the price and isn't deluted. This means you can delute it to your own strength for different causes. You can see it removing dirt as you watch, like someone said above. You can not use it pure on the bike however, it will make alloy parts go dull - as my buddy found out lol. ,,,
Cleaning the core of silencer
You can use a propane torch and heat it up until it glows red hot. It only takes a few minutes to do the whole tube. Let it cool and then scrub over it with a wire brush. When you're done it'll look brand new
Chain lubricant
Most are spray mate but I have used chainsaw oil in the past its very good easy to clean off if it flings and I just used to put it on the chain with an old paint brush.,,,
Running better in cold
Cold air is denser and you'll get more air in the bike and the engine compensates with more fuel. It's cold as hell at 20F outside but damn does the bike run crisp!,,
Oil filter
i always just put some on the o-ring before i put it back in
but no you dont need to have oil on it,
Damage check
This would depend on how you drop the bike. If it just falls over you would check everything on that side that could be damaged. It would be the same for a low speed drop. However if the bike not only gets droped but hits something while sliding you might bend the frame or suspension or damage wheels or controls.,,,
Chain
Put it up on your stand lossen the axel and remove the bolt on the bottom of the shock.
Then tighten your chain and lift your swingarm up until its horizontal with the ground, then the chain should have almost no play. Not completely tight, but almost no play.
Tighten the axel, and the bolt on the shock, and your set,,,
Mud stain
depends on what material is stained..
Aluminium stains can be very tricky to get clean if not impossible...some cleaners will also cause a orange/reddish stain wich will not come out unless you use some harsh chemicals to get them out. problem is it's hard to get to those chemicals.
IF you happen to have a truck wash nearby where they wash the big trucks (18 wheelers)take your parts there and tell them to use some brightener on it it's a chemical that really cleans aluminium.it may cost you a little bit of money but that stuff really works and i haven't been able to find that stuff for private sale anywhere.
the number 2 reasons for stains on the bike are :
1) waiting to long to wash the bike some types of sand/mud especially the red dirt we have down south here will stain a bike if you leave it on the bike not only that it dries as hard as concrete and is very difficult to remove , so was your bike ASAP.
2) washing chemicals. Some chemicals / soaps when they are left too long on aluminium will leave stains as it reacts with the aluminium , these stains are almost impossible to get out. ,,,
Clutch
you need a micrometere or vernier caliper to measure how thick they are that how you tell how worn the clutch is. the manual will list the specificational limit (how thin you should allow them to get and how do the basket and innser hub looks like). if they have small teeth on them they are worn.,
Pipes cleaning
Use stuff called Naval Jelly to get the rust off. All you do is put it on and let it sit for a little bit like 5 or 10 mins and just wipe it off then i put peanut oil on it. It helps prevent the rust and works really good
Chain
Put it up on your stand lossen the axel and remove the bolt on the bottom of the shock.
Then tighten your chain and lift your swingarm up until its horizontal with the ground, then the chain should have almost no play. Not completely tight, but almost no play.
Tighten the axel, and the bolt on the shock, and your set,,,
Oil check
There are usually two methods to check the oil. One is a dipstick and the other is a sight-glass. You should have one or the other somewhere on the side of the engine crankcase. It should be fairly obvious and not require the removal of any body panels. If you can't find a dipstick in the side of the crankcase you will need to get down on your hands and knees and have a look for a sight-glass instead. This will be like a tiny window with a gauge against which you can check the level.
Not finding what you are looking for?