20 Most Recent
2005 Vespa PX 150 - Page 3 Questions & Answers
Vespa wont start after long storage
Check for bad fuel, clogged carburetor and that the battery is still charged. If you store it for long periods put it on a battery tender to be safe.
12/26/2016 5:26:17 AM •
Vespa...
•
Answered
on Dec 26, 2016
The battery is easily drain even i replaced it an new battery, what is the posible problem of my vespa lx 150 ie? Ty
Many answers you need a multimeter or ammeter to measure the quiescent current drawn (power used when nothing turned on)
Set it on the 10a scale and measure the current drawn ,put the leads in series with the battery feed wire.
Causes could be a faulty regulator pack or a short on the stator of the generator,a scuffed cable shorting to earth ,(usually around the brake light switch) or a faulty switch causing a lamp to light continuously . I could go on but that should give you a starting point.
good luck
11/12/2015 11:19:50 PM •
Vespa...
•
Answered
on Nov 12, 2015
Vespa gt stalls
Stephen: On the ModernVespa.com Website, Greasy 125 says: "ign coil on the stator or the ign. pickup (also on stator) would be my first guess.
after that, i'd move onto the cdi
============================
If I helped you, let me know. Thanks.
5/26/2015 3:59:06 AM •
Vespa...
•
Answered
on May 26, 2015
Need circuit diagram for ARLEC 15e 6-24Volt 15Amp Electronic battery charger OR their later model BC58
I can't find a diagram.
The small potentiometer on the control board likely serves as an adjustable component to fine-tune specific parameters. Here are some possibilities:
Voltage Regulation:
The potentiometer might control the output voltage. By adjusting it, you can set the desired charging voltage for different battery types (e.g., 6V or 12V).
Current Limit Adjustment:
It could be used to set the maximum charging current. Adjusting the potentiometer allows you to limit the charging current based on the battery's capacity and condition.
Sensitivity or Threshold:
Some potentiometers act as sensitivity controls. For example, it might adjust the threshold at which the charger switches between charging and maintenance modes.
Setting the Potentiometer:
Without the specific circuit diagram or detailed information about your charger, I recommend the following general steps:
Observe the Potentiometer:
Identify the potentiometer on the control board. Note its position and any markings (if present).
Consult the User Manual:
Check the user manual or operating instructions. It might provide guidance on adjusting the potentiometer.
Trial and Error:
If no specific instructions are available, start with the potentiometer set to its mid-position.
Gradually adjust it while monitoring the charger's behavior (e.g., charging current, voltage).
Observe how the charger responds to changes in the potentiometer setting.
Fine-tune it based on your specific battery type and desired charging characteristics.
Remember that precise adjustments depend on the charger's design and the battery you're charging.
4/18/2024 7:22:52 PM •
Motorcycles
•
Answered
Yesterday
What is the length of lift cables on a 1993 model 2693 hilo camper and any info on what after market part to use ? thanks
The lift cables on a 1993 model 2693 Hilo camper are 30 feet,2 3/4 inches long and fit the standard height lift of 11 feet 8 inches high to the top of the overhead. The lift uses two cables. According to a Hi- Lo camper travel trailer forum, cable replacement is basically the same on all years and models, with the main difference being the length of the cables from model to model. You can use a cable cut chart to find what cable length you need for your camper, and you'll need to know your year, model name, and box (body) length: Lift cables typically wear out after three to five years, so it's important to replace them as needed and keep them regularly maintained.
4/12/2024 1:26:15 AM •
Motorcycles
•
Answered
on Apr 12, 2024
Were do the fuel lines go to on a mountop 150cc
This particular unit has a typical GY6-style engine with a fuel line designated from the gas tank to the carburetor distinguished by an in-line cylindrical fuel filter located near the center of the line. Best to locate the carburetor distinguished by the location of the air filter, there should be a hose going from that unit up into the gas tank.
Ideally, remove the gas tank entirely and it should reveal the gasoline lines directly to the carburetor.
The photo shows the fuel line/filter indicated in red, and the location of the carburetor within the blue indicator.
2/28/2024 4:42:51 PM •
Motorcycles
•
Answered
on Feb 28, 2024
Not finding what you are looking for?