20 Most Recent
2007 Peugeot Speedfight Motorsport 50 - Page 4 Questions & Answers
How to remove filter and clean it?
Year Make Model of the motorcycle please?
Please always include that information as first three words. Then they are thousands of motorcycle categories listed by;
make year model = Suzuki 2003 GSXR1100
If it is the foam type filter, put Dawn Dish Detergent on it, wash out the dirt, dust and oil. Keep squeezing under running water until the water runs clean. Leave to dry. Then spray it with Oil Filter Oil and replace the filter. For paper filters, just replace them if they look dirty.
99-0516 K&N Air Filter Oil - 12.25oz - Aerosol
K&N
https://www.knfilters.ca > 99-0516-air-filter-oil-12-25...
K&N 99-0516 is a 12.25 ounce aerosol can of air filter oil. K&N Air Filter Oil is the only oil specially formulated to work in combination with the cotton ...
US$15.99 · In stock
..
12/12/2023 11:42:00 PM •
Motorcycles
•
Answered
on Dec 12, 2023
Is both wires n the plug the same on voltage regulator
In a voltage regulator plug, the wires may not necessarily carry the same voltage. The voltage regulator is a component in a vehicle's electrical system that controls and regulates the voltage produced by the alternator, ensuring a consistent voltage output to the battery and other electrical components.
In the plug of a voltage regulator, there are typically multiple wires, each serving different purposes and carrying different voltages. For instance:
1. **Voltage Input and Output Wires:** These wires might differ in voltage. The input wire connects to the alternator or battery, carrying the higher voltage that needs regulation. The output wire, connected to the electrical system, carries the regulated voltage for the vehicle's operation.
2. **Ground Wire:** This wire is crucial for completing the circuit and ensuring proper functioning of the voltage regulator. It does not typically carry a voltage; instead, it serves as the return path for the electrical current.
3. **Sensing Wire:** In some regulators, there might be a sensing wire that monitors the system voltage. This wire doesn't usually carry a high voltage but rather acts as a feedback mechanism for the regulator to adjust its output.
It's important to identify and understand the wiring configuration of the voltage regulator plug, as incorrect connections or wiring can lead to electrical issues or even damage to the vehicle's electrical system. Referencing the vehicle's service manual or wiring diagrams specific to the make and model can provide accurate information about the voltage levels and the purpose of each wire in the voltage regulator plug.
12/10/2023 4:28:15 AM •
Motorcycles
•
Answered
on Dec 10, 2023
Vacuum Cleaner - 25.2V Battery not charging question
Either battery is not fully charged or battery require replacement. As you said you have already ordered new charger, charge your battery at full level with original charger. If problem persists then battery needs replacement.
11/3/2023 1:45:09 PM •
Motorcycles
•
Answered
on Nov 03, 2023
I removed key switch on a 2008 yamha star 650 when I put it in gear it shuts off
Here are some possible causes:
Low idle RPM: If your idle RPM is set too low, the bike may shut off when you put it in gear. You can consult a manual to see what the RPM should be.
Side stand switch: Most bikes have a safety switch that shuts down the engine if the side stand is still out. Check if the side stand is still out and if it is, try putting it up.
Clutch lever switch: Most bikes have an electrical switch in the clutch lever as a safety feature so that you can't start it in gear unless the clutch is in. This switch could be faulty.
Safety control box: This box checks all the safety features and kills the engine if needed. It could be faulty.
It's best to take your bike to a professional mechanic who can diagnose and fix the issue for you unless you can check off each of the above as the problem.
https://www.manualslib.com/manual/833178/Yamaha-Xvs650.html
10/27/2023 5:55:15 AM •
Motorcycles
•
Answered
on Oct 27, 2023
On my o6 roadstar 1700. The oil is getting sucked into the carb and smokes terribly. Not for real long though. It runs all the oil out real quick. Anyone have any ideas?
I hope I can help you brother. Crankcases have a breather tube and it expels exhaust gasses, those gases press themselves in between cylinder and piston. It makes the oil black and acid response on coal is not good for engine parts. The breather tube is mostly connected to the low pressure chamber below the air filter. Typically that is close to the air intake for the carburetor. Remove the air filter and its base plate and clean the compartment careful with dust free rags. I don't know of any technical details for this cruiser but there can be valves on front of the carb, small membranes that open on revelations and the known gas slides. Those must not be effected by sticky substances. Oil is not sticky but the intended functioning leaves a residue.
You need in any case, to check the oil level. Also the condition of the oil, so you made sure there is no gray foam from water contamination. Droplets on the dipstick, or on the inspection window glass, indicate fuel in the oil.
When the oil level is between Min and Max or low and it turns out to be pure, then I suspect you have a leaking piston ring or even a damaged piston side wall. I would not ride the bike far before you know certain. You also wouldn't want a sudden stop.The compression blows in hard and unnoticed, the slow sucking breather tube is then turned into a hose. After each ride the access spill can flow down the carb. Compression can be tested in a shop but turning the engine over without spark, may provide audible evidence when the compression is really low in one cylinder. I ones had an unnoticed broken piston ring, on a moped and that damaged the piston. Best of luck
10/25/2023 3:56:25 AM •
Motorcycles
•
Answered
on Oct 25, 2023
Not finding what you are looking for?
