Top 20
2009 Harley Davidson FLSTC Heritage Softail Classic Questions & Answers
How do I test the stator on a 2009 heritage softail
To check the STATOR. Turn ignition key switch OFF, then disconnect the voltage regulator connector from alternator stator wiring. THEN connect an ohmmeter set on the RX1 scale with one lead into either of the stator sockets and the other lead to a good ground. And test for continuity - a good stator will show no continuity (0 ohms) across either stator socket - any other reading indicates a grounded stator which must be replaced. THEN remove the ground lead and insert lead it into the other stator socket - the resistance (with ohmmeter still set on the RX1 scale)should be 0.1-0.2 ohms - if the resistance is lower a stator short is indicated. Which means that the stator is damaged and must be replaced. - if the resistance is higher (OL on meter), an open is indicated and again, the stator is damaged and must be replaced. You should check socket 1 to 2 then 1 to 3 then 2 to 3. (If you only had a two wire stator you would check between wires/sockets 1 and 2).
Before testing short out the ohmmeter leads against each other and if they do not produce a reading of0 ohms subtract the reading you do get from any readings you get doing the stator checks in order to get accurate stator circuit readings, otherwise you may have out of range reading due to the internal and/or lead resistance of the ohmmeter.
10/10/2014 1:25:44 AM •
2009 Harley...
•
1,006 views • 0 helpful votes
How do I change primary fluid 2009 FLSTC
Remove drain plug on bottom center of primary case to drain it. remove derby cover o refill it and ONLY until the fluid just touches the bottom of the clutch diaphragm spring.
Where is the brake light switch on a 2009 harley
There are two.The front switch is inside the right handlebar switch housing (START, RUN/OFF kill switch, RIGHT TURN SIGNAL) and operates off the front brake lever.The usual problem with this is it either sticks, or the "tit" that works off the brake lever gets broken off, usually because the front master cylinder wasn\'t installed by the correct procedure.Usual results is the brake light will not turn off with the ignition on.The other switch is located along the rear brake hydraulic line.Start at the master cylinder and follow the line back to the rear caliper, and you\'ll find it eventually.It appears Harley has a problem with the rear brake light switch on this year, as it tends to spring a leak, brake pedal goes all the way down without stopping, sometimes smoking from the brake fluid being sprayed on hot engine parts, etc.
CLUNK SOUND WHEN STARTING
This is probably the starter gear engaging in the engine. Shouldn't be a problem unless it doesn't engage properly.
Harley davidson motorcycle
If the right/left blinkers are going off, that's a sign that the security system is still active, disabling the starter system.For some reason, your fob is are not turning off the system.Try replacing the fob's battery, or check it's contacts for corrosion.
How do I put the
There is a spring hook up where the kickstand bolts onto the frame. I loosen the two bolts that holds this on and put the spring on with the stood up straight and the kick stand in it's extended position. You still may have to stretch the sping using a spring hook to get it on.
Steve
1992 Harley-Davidson Softail Heritage Classic. What engine is this, engine # BLLN011421?
If the serial number on your motor doesn't correspond directly to an S&S motor, it's possible that the lower end, which includes the crankcase, might be a Harley Davidson component. S&S often manufactures performance parts that are compatible with Harley engines, including jugs and heads, which might be installed on a Harley lower end. This hybrid setup isn't uncommon in customized or modified motorcycles. It might be beneficial to consult with a motorcycle mechanic or a specialist familiar with Harley and S&S components to verify the specifics of your engine setup.
Not finding what you are looking for?