20 Most Recent
2000 Aprilia RS 125 - Page 9 Questions & Answers
Ive only had it six
For carb checkout:
http://www.facebook.com/note.php?note_id=137859818194&ref=mf
For air filter:
How to remove and clean the airfilter
- Remove the seat.
- Remove the bolt at the top of the petrol tank to the chassis.
- Turn the fuel off
- Disconnect the fuel line.
- Take the airbox lid off
- Remove the air filter
- Stuff a clean rag into the cavity
- Manually remove any large particules from the foam.
- Soak the foam in air filter oil or 80W/90 gear oil.
- Squeeze off any excess (it should remain damp).
- Remove the rag
- Refit the foam
- Reinstall the lid
- Reconnect the fuel lineReconnect the tank.
How do i clean my
Remove it, pull apart, let it soak for couple hours in solvent or submerge in carb cleaner. Blow out all the jets. Make sure floats are clean. Let air dry or air blow dry.
My aprilia rs 125 2003
Try cleaning the carb and the air filters. It seems that the air/fuel is not mixing in appropriate quantity.
When started jumps to 7
sounds like a loose of fuel pressure, the revs go up as the fuel mixture leans out, then once the fuel press is gone it stalls out. check for a dective fuel pump run circuit issue.
My aprila rs50 starts fine and runs fine cold but if it heats up abit you pull the throttle and it sounds like its dieng
Instructions
-
-
1
Park your RSV 1000R on a well-ventilated, level area, using its kickstand.
-
2
Start the engine and let it idle in place until the
temperature gauge built into the instrument cluster indicates a minimum
internal temperature of 180 degrees Fahrenheit. This is the motorcycle's
ideal operating temperature.
-
3
Take note of the engine idle speed, using the tachometer
needle, while the engine is running. Ideally, the engine should idle
steadily at 1,250 rpm.
-
4
Adjust the engine idle speed to 1,250 rpm, using the idle
adjuster screw hidden between the lower right edge of the fuel tank and
the upper edge of the right middle fairing panel. Turn the idle adjuster
screw clockwise to increase the engine idle speed, or counterclockwise
to decrease the engine idle speed, using a small flat screwdriver if
your RSV 1000R's frame (VIN number) precedes ZD4MEE009YS000292. A
plastic knob allows the engine idle speed to adjusted by hand on RSV
1000R models with a frame (VIN) numbers starting from ZD4MEE009YS000293.
-
5
Rev the engine two to three times and observe the
tachometer. The engine should return to a 1,250 rpm idle. Adjust the
engine idle speed as needed, using the method described, then rev the
engine again. Problems may exist within the throttle control,
fuel-injection system or engine, if the engine idle speed will not hold
steady at 1,250 rpm. Contact your local Aprilia service facility for
assistance.
-
6
Stop the engine, once you have obtained a steady 1,250 rpm idle speed.
5/20/2022 6:46:22 AM •
Aprilia...
•
Answered
on May 20, 2022
Will not start Aprilia Mojito Custom
OK< can you provide more details? Does it turn over? Does it fire at all? Do you know if you have a spark? Do you know if fuel is getting through? Has it run properly recently?
To run, a motor needs fuel, air and spark
Inspect all fuel lines and wires. Pull the sparkplug and see if it is burnt/wet/corroded
3/14/2020 6:57:54 AM •
Aprilia...
•
Answered
on Mar 14, 2020
I have installed a new ignition on y aprillia pegaso 2008 and it wont accept the code numbers
It's not the new switch, it's the new keys that have to be programmed.
The keys have uniquely coded chips in them, when you turn on the ECU uses the antenna that is by the ignition switch to look for a code that it recognises, you need to introduce the new key codes to the ECU.
This is what the manual says:
In case of installation of a new ignition switch the procedure is as follows:
Turn ON using new key
The dashboard will not recognise the key and will ask for the customer code: insert the customer code. It is 00000 when supplied. It can be changed to any numeric five digit number.
Now you can enter: MENU, DIAGNOSIS (insert the service code 25973),
Then select MODIFY KEYS and implement the procedure.
If you are not sure about the mode switch, this is what you do:
Use handlebar "mode" switch (left / right) to select "Menu" option on the screen, then press mode switch in to enter.
Use handlebar "mode" switch to select "Diagnosis", press to enter.
Use handlebar "mode" switch to enter the workshop code (25973).
When you have selected the digit you want then press in and it will move to the next digit etc.
You can't screw anything up, if you do it wrong go back or turn off and start again.
2/26/2019 7:27:02 PM •
Aprilia...
•
Answered
on Feb 26, 2019
Not finding what you are looking for?