20 Most Recent
1972 Honda CB 250 - Page 7 Questions & Answers
Lost speed
Remove the water trap bowl at the bottom of the petcock, (gas valve). Is there any water or trash in the bowl? Drain a cup of gas from the tank. Is there any water or trash in the cup? Dump it, clean it and re-mount it, ( not all bikes have a water trap bowl ).
FOR EACH CARB >
Drain the carburetor. There should be a screw on the lower side of the carb float bowl. Remove the screw then replace it after the fuel drains. Turn the gas back on and wait a minute for the carb to fill with gas. Install a new stock NGK spark plug and try to start the engine. If the bike doesn't start and run properly then shut off the gas and remove the carburetor from the engine.
Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Remove the idle screw and the air screw on the outside throat of the carb and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two screws down. Only screw these in until they LIGHTLY seat. Now turn each screw one and one half turns outward. Put the rest of the carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine. This process should get you back on the road.
Please rate this solution. Thanks!
Lost the ability to pick up speed quickly
Hi and welcome to FixYa,
Initially, check for any leak in the air filter box / enclosure or if the air filter is seated/installed correctly. Additionally, ensure that the air box is fitted correctly.
Postback results and other symptoms or anything out of the ordinary: is the failure to pick up speed at a particular RPM range, at any gear, has the bike been not used for some time, do you use a regular filling station, change in weather/temperature.
Good luck and thank you for using FixYa.
Front wheel bearing removal.
The bearings get punched out of the hub evenly. Just take a small to medium sized hammer and a large punch and drive the old bearings outward from the center of the hub. Install the new bearings somewhat more gently than the old ones came out. The bearings must go into the hub
straight. Tap them in with a plastic hammer. Once the bearing is started, place the old bearing on top of the new one and strike around the outer rim of the old bearing to seat the new bearing.
Go to this site to download a free
PDF service manual. Your bike is on the
list of manuals. See page 71.
http://www.carlsalter.com/motorcycle-manuals.asp
Please take a moment and rate this answer as a Fix. Thanks!
Cant get a spark from ht leads on cb250 motor bike
Be CERTAIN the battery is good. Are all fuses good? Try brand new spark plugs. Disconnect the kill switch on the handle bar. Check the side stand kill switch for proper operation. Have the shop check the CDI ignition.
Please rate this solution. Thanks!
Honda PC50 moped VIN decoder
To read the serial number on a Honda PC50 moped, follow these steps:
Locate the VIN (Vehicle Identification Number): The VIN is a unique code that provides information about your moped. On a Honda PC50, you can find the VIN in the following places:
Under the Air Filter Cover: Look on the left-hand side, just above the engine. The VIN should be stamped there. It typically looks like this: PC50 - 1234567.
Frame Number: The frame number is another term for the VIN. It's usually located near the air filter body.
Decode the VIN: The VIN contains important details about your moped, including the year of manufacture. Here's how to interpret it:
The 9th digit of the VIN is a check digit.
The 10th digit represents the year code. For example:
A = 1980
B = 1981
C = 1982
D = 1983
E = 1984
F = 1985
G = 1986
H = 1987
J = 1988
K = 1989
L = 1990
M = 1991
N = 1992
P = 1993
R = 1994
S = 1995
T = 1996
V = 1997
W = 1998
X = 1999
1 = 2000
2 = 2001
3 = 2002
Note that if your scooter was manufactured between February 1986 and February 1987, it's likely to be a '87 model;
Additional Resources:
If you have the full VIN, you can use the NHTSA VIN decoder to get detailed information about your moped.
Alternatively, you can call Honda with your VIN, and they will provide you with the necessary information.
4/23/2024 11:45:02 PM •
Honda...
•
Answered
10 hours ago
Honda 500 TRX fa6 has PS on the dash….what does it mean ?
The Power Steering has failed. There has been a factory recall for a suddenly failing electrical steering shaft, that could cause the rider to loose control. This does not have to be your problem but anyhow either the electronics or the pump failed. Error codes or messages usually have to be erased by a simple reset procedure or disconnecting a plug, after repairs are done.
3/31/2024 4:25:47 AM •
Honda...
•
Answered
on Mar 31, 2024
Hiss works but
On the bottom of your speedometer on the left side there is 2 buttons
press the far left one for a couple of seconds and the light should go on
1/8/2024 6:42:24 AM •
Honda...
•
Answered
on Jan 08, 2024
What to torque the head on my 99 CBR 929 Honda in
For a 1999 Honda CBR929RR, the cylinder head bolt torque specifications are essential to ensure proper engine assembly and function. When tightening the cylinder head bolts, it's crucial to follow the manufacturer's recommended torque settings to prevent damage to the engine components.
For the CBR929RR, the cylinder head bolt torque specifications are typically as follows:
1. **Initial Torque:** 29 Nm (2.9 kgf-m, 22 ft-lbs)
2. **Final Torque:** 64 Nm (6.4 kgf-m, 47 ft-lbs)
It's essential to tighten the cylinder head bolts in the specified sequence and in multiple stages, gradually increasing the torque until reaching the final specified torque. The exact tightening sequence can usually be found in the service manual specific to your motorcycle model.
When torquing the head bolts, ensure you're using a reliable torque wrench calibrated in the appropriate units (Nm or ft-lbs). Always follow the tightening sequence precisely to ensure even pressure distribution across the cylinder head gasket.
Additionally, it's advisable to use new cylinder head bolts if the old ones have been previously tightened or stretched beyond their yield point. This helps maintain proper clamping force and ensures the integrity of the engine assembly.
As always, referring to the service manual or consulting a professional mechanic experienced with motorcycle engine assembly can provide additional guidance and ensure the correct torque settings are applied during the cylinder head installation process.
12/10/2023 4:27:33 AM •
Honda...
•
Answered
on Dec 10, 2023
2006 Honda Shadow Arrow 750 VT missing on the rear cylinder fire
. One possibility is that the spark plug or plug wire is faulty 1. Another possibility is that the carburetor needs cleaning and adjustment It could also be due to a valve adjustment issue or a bent rod.
I would recommend taking your motorcycle to a professional mechanic who can diagnose and fix the issue. If you prefer to troubleshoot it yourself, you can start by checking the spark plug and plug wire for any damage or wear and cleaning the carburetor. However, please note that working on a motorcycle engine can be dangerous and requires specialized knowledge and tools. Please take all necessary safety precautions and follow the manufacturer's instructions when working on your motorcycle.
10/22/2023 2:01:22 PM •
Honda...
•
Answered
on Oct 22, 2023
2007 honda shadow vt750 dies sputters on acceleration
The problem might be with the air filter, and if not there are a few other things that could be causing your Shadow engine to bog down on acceleration. This includes a dirty carburetor, carb adjustment issues, or other internal problems like damaged vacuum lines or a cracked manifold
8/31/2023 7:57:51 AM •
Honda...
•
Answered
on Aug 31, 2023
Just brought a Honda C102 Step Through. Does anybody know if its positive earth or negative earth. I just brought battery for it.
Question edited for clarity.
Question moved from Honda Cars.
I haven't seen one of those for 40 years!
The Braided cable goes to battery negative -
They normally have a Red Cable to the battery Positive +
And if I recall, there is an inline fuse in the positive?
Here is the cable
https://www.ebay.com/itm/NOS-OEM-Honda-Cub-50-70-C70-K1-C50-C65-M-CA102-C102-Cable-Earth-Battery-Ground-/172214475304?_ul=IN
and here
https://www.ebay.com/itm/225016392400
Service manuals x two :>D
Honda C102 Service manual
Honda 4-stroke.net
https://4-stroke.net > honda-c102 > downloads > 440-...
You can go to our downloads and grab yourself a copy! Download the Honda C102 Service Manual in the following format: pdf Service manual for Honda C102 (1.93 MB).
Service Repair Manual Honda C100, C102, C50,C70, C90
Blogger
http://myhondac100.blogspot.com > 2013/10 > servic...
Oct 21, 2013 - Service Repair Manual Honda C100, C102, C50,C70, C90.
http://www.servicerepairmanualonline.com/4449/honda-super-cub-50-c50- ...
7/22/2023 4:05:21 PM •
Honda...
•
Answered
on Jul 22, 2023
Not finding what you are looking for?