20 Most Recent
1984 Honda VF 1000 R Questions & Answers
Where are the seat hold down bolts, 1984 Honda Saber 700
I had the 84 vf700S Sabre, and I suspect it\'s similar. Removing the seat on mine was simple. Take your key, unlock the helmet lock on the LEFT side of the bike under the passenger space. Once unlocked, the metal is a lever that pushes away from the locking hinge of the helmet lock and it releases the "middle" of the seat. The front of the seat is a tongue that goes underneath the tank. Hope this helps.
I have a honda vf1000
To change your oil you will need 4 quarts of oil, a filter, and a new aluminum drain plug washer. You can reuse the old drain plug washer if it has not been squished out of shape. Your motorcycle comes from Honda usually with 10w-40 mineral base motorcycle oil. You can use any oil that is JASO MA certified motorcycle oil. 10w-40 for cold climate. 20w-50 for warm climate/touring. Automotive oils use different additives and may cause scoring in certain types of cam bearings. Do not use any oil that says " Energy Conserving " on the label . It will shorten the life of your wet clutch and transmission gears. If you choose Synthetic oils, they will help your bike run cooler and shift easier. Pour in 3.4 quarts of oil to reach the high mark on the dip stick or inspection window. Make sure the motorcycle is upright or on the center stand when checking the level . Run the motor for a minute or two to fill the oil filter compartment with oil. Now recheck the oil level and top up as needed. If you want to try an inexpensive full synthetic oil that is JASO MA rated 15w-40 Shell Rotella T Synthetic fits the bill at about $22 per gallon. All brands/manufacturers make a motorcycle oil. Some are very hard to find. Just make sure that the oil you pick has the JASO MA Japanese engine Rating to protect your motorcycle engine.
Headlight
Check your light switch it may be dirty ,causeing a bad contact .Try using some W/D 40 .this may help .
Where do i locate the air filter for 1984 Honda VF
Most all motorcycles air filters are located underneath the fuel tank.
take off seat...turn fuel selector to off...disconnect hose from fuel filter, take off hold down bolts for tank then have some rags ready for a little fuel leakage and since your going to change or inspect air filter now would be a good time to change or spray clean your fuel filter. if the air filter is not under the tank, then just follow back from your carburetor manifolds tubes.
I have a VF 1000 R in Australia and wish to ship
If you look on the exhaust you will see stamped in the muffler information on the noise and emission.
By the way a 1984 bike did not have any EPA issues to adhere to other than noise, which was not enforced very often if at all.
I have a 1984 honda vf1000 motorcycle and 2nd gear
Replace gears in sets, the bad gear and the gear it meshes with. In what way is 2nd gear going bad? The gear may be fine and the shift fork is the problem.
Google " vintage honda motorcycle parts " and google " honda motorcycle salvage " for parts.
Honda PC50 moped VIN decoder
To read the serial number on a Honda PC50 moped, follow these steps:
Locate the VIN (Vehicle Identification Number): The VIN is a unique code that provides information about your moped. On a Honda PC50, you can find the VIN in the following places:
Under the Air Filter Cover: Look on the left-hand side, just above the engine. The VIN should be stamped there. It typically looks like this: PC50 - 1234567.
Frame Number: The frame number is another term for the VIN. It's usually located near the air filter body.
Decode the VIN: The VIN contains important details about your moped, including the year of manufacture. Here's how to interpret it:
The 9th digit of the VIN is a check digit.
The 10th digit represents the year code. For example:
A = 1980
B = 1981
C = 1982
D = 1983
E = 1984
F = 1985
G = 1986
H = 1987
J = 1988
K = 1989
L = 1990
M = 1991
N = 1992
P = 1993
R = 1994
S = 1995
T = 1996
V = 1997
W = 1998
X = 1999
1 = 2000
2 = 2001
3 = 2002
Note that if your scooter was manufactured between February 1986 and February 1987, it's likely to be a '87 model;
Additional Resources:
If you have the full VIN, you can use the NHTSA VIN decoder to get detailed information about your moped.
Alternatively, you can call Honda with your VIN, and they will provide you with the necessary information.
4/23/2024 11:45:02 PM •
Honda...
•
Answered
Yesterday
Honda 500 TRX fa6 has PS on the dash….what does it mean ?
The Power Steering has failed. There has been a factory recall for a suddenly failing electrical steering shaft, that could cause the rider to loose control. This does not have to be your problem but anyhow either the electronics or the pump failed. Error codes or messages usually have to be erased by a simple reset procedure or disconnecting a plug, after repairs are done.
3/31/2024 4:25:47 AM •
Honda...
•
Answered
on Mar 31, 2024
Hiss works but
On the bottom of your speedometer on the left side there is 2 buttons
press the far left one for a couple of seconds and the light should go on
1/8/2024 6:42:24 AM •
Honda...
•
Answered
on Jan 08, 2024
What to torque the head on my 99 CBR 929 Honda in
For a 1999 Honda CBR929RR, the cylinder head bolt torque specifications are essential to ensure proper engine assembly and function. When tightening the cylinder head bolts, it's crucial to follow the manufacturer's recommended torque settings to prevent damage to the engine components.
For the CBR929RR, the cylinder head bolt torque specifications are typically as follows:
1. **Initial Torque:** 29 Nm (2.9 kgf-m, 22 ft-lbs)
2. **Final Torque:** 64 Nm (6.4 kgf-m, 47 ft-lbs)
It's essential to tighten the cylinder head bolts in the specified sequence and in multiple stages, gradually increasing the torque until reaching the final specified torque. The exact tightening sequence can usually be found in the service manual specific to your motorcycle model.
When torquing the head bolts, ensure you're using a reliable torque wrench calibrated in the appropriate units (Nm or ft-lbs). Always follow the tightening sequence precisely to ensure even pressure distribution across the cylinder head gasket.
Additionally, it's advisable to use new cylinder head bolts if the old ones have been previously tightened or stretched beyond their yield point. This helps maintain proper clamping force and ensures the integrity of the engine assembly.
As always, referring to the service manual or consulting a professional mechanic experienced with motorcycle engine assembly can provide additional guidance and ensure the correct torque settings are applied during the cylinder head installation process.
12/10/2023 4:27:33 AM •
Honda...
•
Answered
on Dec 10, 2023
Not finding what you are looking for?