20 Most Recent 2000 Husaberg Fe 400 Questions & Answers


Hi, Bari182 the vast majority of service, parts fiche, and owners manuals on the internet are "FREE" to download and all service manuals contain wiring diagrams in the back pages. The rest usually charge a modest fee of $15 and there is a handful of obscure, rare, obsolete, and very old models that are no longer or never were available and some were never printed in English. The Indian and Philippine markets are usually in E-book format only, for these rare occasions I shall look on eBay and find the cheapest one available. Most of the manuals will cover your exact make, model, and year otherwise one will be provided that comes as close as possible to your bike and will have most of the same info that an exact manual would have. If there is no $ sign after the manual link it is free to download.
To download your manual for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://husaberg.org/service-manuals
http://www.cyclebuy.com/husaberg/parts.htm
HUSABERG ENDURO FE 400 Owner Manual
https://bikez.com/motorcycles/husaberg_fe_400_e_2000.php
https://en.wikipedia.org/wiki/Husaberg

2000 Husaberg Fe... | Answered on Jun 13, 2019


Hi, Renolds713 and the usual suspects are:
1. Fuel tank empty.
2. The fuel tank has old dead gas.
3. Fuel tank bottom contaminated with ethanol sludge, dirt, water, rust, etc.
4. Fuel supply valve/petcock turned off.
5. Fouled spark plugs.
6. Engine flooded as a result of overuse of the choke.
7. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
8. Fuel valve/petcock or filter clogged.
9. Fuel line to carburetor or throttle body pinched, kinked or blocked.
10. Carburetor float stuck.
11. Fuel injectors clogged.
12. Fuel injectors stuck open.
13. Quick disconnect check ball stuck.
14. Compression below 75 PSI.
15. A stuck-bent-burnt valve.
16. Improper valve clearance (too tight)
17. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a cursory reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
18. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
19. Loose or corroded wire connection at the coil or plug between ignition sensor and ECM module.
20. Spark plug cables in bad condition and shorting check for spark leakage in the dark, cable connections are loose or connected to the wrong cylinders.
21. Ignition timing incorrect due to a faulty ignition coil, ignition module or MAP, CMP, CKP, O2, TPS, ETP, IAC sensors.
22. Faulty neutral, clutch, kickstand safety switch.
23. Faulty fuel pump or fuse or relay.
24. Faulty or corroded run/stop switch.
25. Tilt sensor needs a reset.
26. Security system not disarming alarm needs a reset.
27. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://husaberg.org/mechanical/19382-husaberg-400-fe-1997-no-start.html
What To Do If Your Motorcycle Doesn Start
http://husaberg.org/service-manuals
http://www.cyclebuy.com/husaberg/parts.htm
Husaberg 400 User Manual

2000 Husaberg Fe... | Answered on Jun 13, 2019


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Husaberg, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?q=Wiring+diagram+2000+Husaberg+Fe+400&tbm=isch&source=univ&sa=X&ved=2ahUKEwiX8r2E9-XiAhVFnFkKHTVyCtMQsAR6BAgAEAE&biw=1440&bih=757
https://www.manualslib.com/manual/1088074/Husaberg-Enduro-Fe-400.html?page=31
http://husaberg.org/service-manuals
http://www.cyclebuy.com/husaberg/parts.htm
Husaberg 400 User Manual

2000 Husaberg Fe... | Answered on Jun 13, 2019


Hi, Anonymous and the usual suspects are:
1. Spark plugs in bad condition or have an improper gap or are partially fouled.
2. Spark plug cables in bad condition.
3. Battery damaged or nearly discharged, should have 12.5 volts.
4. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Throttle controls not adjusted correctly.
6. Water or dirt in the fuel system.
7. Water or dirt in the carburetor.
8. Intake air leak.
9. Fuel tank vent hose and vapor valve plugged, or fuel line closed off, restricting fuel flow.
10. Choke valve inoperative.
11. Engine lubricant to heavy (winter operation).
12. Ignition is not functioning properly (possible sensor failure).
13. Faulty ignition coil.
14. Valves sticking.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Starting problem Husaberg FE400 03
2003 fe400e starting problems
http://www.husaberg.no/Teknisk%20data%20Husaberg/Verkstedhandboker/RA_Husaberg_2005_E_05.pdf
Husaberg Parts Dirt Bike Motocross
Husaberg 400 User Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2000 Husaberg Fe... | Answered on Oct 08, 2017


Sounds too large, I would have thought something more like 0.008" for inlet and 0.010" for exhaust?

2000 Husaberg Fe... | Answered on Feb 17, 2011


make sure your cut off switch isnt on or it could be the ht lead

2000 Husaberg Fe... | Answered on Feb 04, 2011


di solito localizzato dal collo e dal radiatore

2000 Husaberg Fe... | Answered on Dec 14, 2010


Hi ..... The majority of throttles close with the use of a second cable and/or the return spring on the carb. Make sure you have approx' 0.2 of a movement before throttle starts to open, second cable (closing one) is 'tight', it can be adjusted at bars and carb and that the cables are correctly routed (manual will have a diagram). Try lubricating cable(s) and throttle tube on the bars. It'll be something simple .......... let us know how you get on.

2000 Husaberg Fe... | Answered on Dec 22, 2008


but when the bike's stood for over 4 hours it's flat Confused Even with the main switch off Any ideas?OK beg,borrow, or steal a multitester with current(amps) reading on it. 10 amps is more than ideal, but you will probably need less after initial tests. Ammeters need to be in series, not in parallel like volt testers, so disconnect one battery lead(either will do) and complete the circuit by putting the multimeter leads between the battery lead(disconnected) and the battery terminal. You are now gonna see on the meter, every amp pulled from the battery. turn the ign on and turn a light on, you will see the current rise, as amps are drawn, ok! Turn the ignition off and see what happens. Probably with it set on the 10amp scale youll see nowt, so go down the range on the meter into milliamps, and my guess is that you will see a reading. You shouldnt see anything at all with ign off, but Id guess you can see a few milliamps on the gauge. If this is the case, proceed as follows: One by one, remove the bikes fuses and replace them, if at any point the reading drops to zero you have found the circuit which is sucking the power. If that fails, try again, but one by one undo (every) multiplug on the bike, again one of em should cause the reading to drop. When you have found a fuse or a plug that causes the meter to read zero amps, check that circuit. Maybe there is a wire rubbing onto the frame, a switch corroded internally, or similar, but now you know the bit you need to fix. If you connect the meter as described and there is NO current drain, you are either special! or leaving the side light circuit on(muppet!) good luck.,,,

2000 Husaberg Fe... | Answered on Nov 10, 2008


and had the bike souped for it. Anyway the throttle is SUPER touchy.. You breath on it and it takes off.. Because of this I ended up dumpin it 30 min after I got on..haha... My question is is there a way to stiffen up the throttle so that i have to crank the grip harder to give it gas? I am very inexperienced, and when it took off, i tensed up, hittin the throttle even harder. I know i will appreciate the the responsiveness when I get more experience, but i dont want to die in the process..lol.. thanks for you help! ,UYou need to learn to hold on to the bike with your legs, so you aren't pulling on the bars during acceleraion. The throttles are supposed to be easy to turn, so that it will snap completely closed when you let off. You can replace the throttle cam (the part that the cable attaches to) with a slower-opening unit that will give you more control. The amount you have to turn the throttle from closed to full-open will stay thesame, but it will open slower in the first half of the throttle pull, keeping you from getting such an abrupt surge of power. Once you get a little more time on the bike, you won't have this issue any longer. You will learn proper throttle control, and your wrist will get used to the throttle pull. ,,,

2000 Husaberg Fe... | Answered on Nov 10, 2008


and when the forks/bars/tripleclamps are straight the wheel goes towards the right. ii think they are twisted or bent. how much do new forks cost?Loosen your front wheel slightly. Loosen your fork clamp bolts on the triple clamps slighty. Hold the front brake lever. Put one leg on either side of the front wheel to keep it from moving. Use the handlebars to turn the front end back straight. Tighten everything back up using a torque wrench and torqueing to the proper values from your service manual. Go ride and have fun. ,

2000 Husaberg Fe... | Answered on Nov 10, 2008


depends on what material is stained.. Aluminium stains can be very tricky to get clean if not impossible...some cleaners will also cause a orange/reddish stain wich will not come out unless you use some harsh chemicals to get them out. problem is it's hard to get to those chemicals. IF you happen to have a truck wash nearby where they wash the big trucks (18 wheelers)take your parts there and tell them to use some brightener on it it's a chemical that really cleans aluminium.it may cost you a little bit of money but that stuff really works and i haven't been able to find that stuff for private sale anywhere. the number 2 reasons for stains on the bike are : 1) waiting to long to wash the bike some types of sand/mud especially the red dirt we have down south here will stain a bike if you leave it on the bike not only that it dries as hard as concrete and is very difficult to remove , so was your bike ASAP. 2) washing chemicals. Some chemicals / soaps when they are left too long on aluminium will leave stains as it reacts with the aluminium , these stains are almost impossible to get out. ,,,

2000 Husaberg Fe... | Answered on Nov 10, 2008


Backfires are when fuel travels through the cylinders without combusting then explodes in the exhaust pipe. Fuel supply/combustion issue. It seems likely there's a problem either with the mix going into the cylinders (carbs fuel lines or air intake), or with timing. These can affect a bike at particular speeds and throttle positions. If using the choke has helped at some point that's a further indication (the choke changes the gas/air mix). ,,,

2000 Husaberg Fe... | Answered on Nov 10, 2008


Hi, Anonymous and the usual suspects are:
1. Fuel cap or fuel tank is not venting properly.
2. Fuel filter clogged.
3. Fuel line pinched or kinked.
4. Vacuum line from the petcock to intake manifold cracked.
5. Float needle and seat sticking.
6. Float level too low.
7. Carburetor bowl vent line clogged/blocked/pinched.
8. Idle adjusting screw set too low.
9. Air/fuel mixture screw set too lean.
10. Idle port, transfer ports, slow air jet clogged.
11. Slow fuel jet clogged.
12. Faulty fuel pump.
13. Faulty auto choke or wiring connection.
For more information about your issue and valuable "Free" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://husaberg.org/fuel/5956-only-runs-choke-any-hints.html
WHY your motorcycle only runs on CHOKE
https://www.repair-manuals.eu/cat/motorcycle_repair_workshop_manuals/repair_manuals_husaberg
http://www.cyclebuy.com/husaberg/parts.htm
https://www.manualslib.com/manual/813892/Husaberg-E-400-E.html#product-FC%20550/4

Husaberg... | Answered on Jun 13, 2019


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Husaberg, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?q=Replace+the+battery+2002+husaberg+470-fxe&source=lnms&tbm=isch&sa=X&ved=0ahUKEwjHooyGkObiAhXqqFkKHcIWB3kQ_AUIESgC&biw=1440&bih=757
http://husaberg.org/electrical/9274-new-owner-fx-470-2002-battery-replacement-question.html
http://husaberg.org/mechanical/11215-workshop-manual.html
http://www.cyclebuy.com/husaberg/parts.htm
https://www.manualslib.com/manual/640214/Husaberg-05.html

Husaberg... | Answered on Jun 13, 2019


The main fuse protects all power consumers of the vehicle. It is located in the starter relay housing under the air filter box lid. (A spare fuse is located in the starter relay)

The fuse box containing the fuses of individual power consumers is located under the seat

Husaberg... | Answered on Feb 26, 2017


Hi, Pete and the usual suspects are:
1. Severely drained or faulty battery.
2. Faulty regulator/rectifier or high output coil.
3. Faulty power valve, solenoid or installation.
4. Clogged air filter or exhaust.
5. Cracked or incorrect float level.
6. Float needle is not seating.
7. Faulty reed valve.
For more information about your question please visit the website below. Good luck and have a nice day.
HUSABERG Pure Enduro Service

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Husaberg... | Answered on Nov 11, 2015


Its a long shot, but try Youtube.
They have tons of DIY videos.

Husaberg... | Answered on Jan 08, 2015


Basically the only way water can get in the oil is if there is a corrosion hole in the housing behind the pump impellor. Water pumps have only 1 seal and if that leaks water will drain from a hole in the pump housing under neath the pump.

Husaberg... | Answered on Mar 11, 2013

Not finding what you are looking for?
2000 Husaberg Fe 400 Logo

Popular Tags

16 questions posted

Ask a Question

Usually answered in minutes!

Top Husaberg Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5962 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Strech
Strech

Level 3 Expert

1562 Answers

Are you a Husaberg Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Fe 400 Husaberg

  • Fe 400 Husaberg

Most Popular Question

husaberg fe 400 backfire

  • Motorcycles
Loading...