20 Most Recent
2000 Husaberg Fe 501 - Page 10 Questions & Answers
I have a 98 tl 1000 it throws a code of f1 and runs horrible shooting flames out of the pipes
It sounds like your 1998 TL 1000 has a major problem. The F1 code typically indicates an issue with the fuel system, so you may need to check the fuel injectors and replace any faulty or clogged ones. Additionally, make sure all of the hoses and fuel lines are connected properly, as well as check for any signs of damage or corrosion. If everything looks good there, then it's possible that you may need to replace the fuel pump or other internal components.
1/30/2023 5:37:06 PM •
Motorcycles
•
Answered
on Jan 30, 2023
Mio Soul i 125 rear axle nut tightening torque value
The tightening torque value for the rear wheel nut of a Yamaha Mio Soul i 125 motorcycle is typically around 70-80 Nm (Newton meter). This torque value is the amount of force required to tighten the nut to the proper level.
It's important to use a torque wrench to tighten the nut, this will ensure that the nut is tightened to the proper torque level without over tightening it, which can cause damage to the threads or the hub.
It's also important to note that the torque value may vary depending on the specific model and year of the motorcycle, so it is best to consult the owner's manual or the manufacturer's website for the specific torque value for your motorcycle.
It's also important to check the torque every time you change a tire or make any adjustment to the wheels, to ensure that the wheels are properly secured and to prevent accidents or damage to the motorcycle.
1/24/2023 7:49:49 AM •
Motorcycles
•
Answered
on Jan 24, 2023
2001 softailduece cable throttle: i sprayed contact cleaner in switches due to starter sticking .tried loosening adjusters but no twist
It sounds like there may be an issue with the cable throttle on your 2001 Softail Deuce motorcycle after using contact cleaner on the switches. Here are some things you can try to fix the problem:
- Check the cable for any kinks, frays or breaks. If the cable is damaged, it will need to be replaced.
- Check the cable routing and make sure it is not bound or pinched.
- Check the cable adjusters to make sure they are not seized or stuck.
- Check the throttle grip for any damage or wear, and make sure it is properly lubricated and adjusted.
- Check the throttle control mechanism and make sure it is properly lubricated and adjusted.
- Check the carburetor or fuel injection system to make sure they are properly adjusted and functioning correctly.
- If the above steps do not resolve the issue, it may be best to take the motorcycle to a professional technician or contact the manufacturer for further assistance or service.
It is important to note that, the above steps are general troubleshooting steps, and the actual problem can be caused by different things, so it is best to consult a service manual for your specific 2001 Softail Deuce motorcycle or contact the manufacturer for more detailed and accurate information.
1/23/2023 1:01:08 PM •
Motorcycles
•
Answered
on Jan 23, 2023
How do I get rebuild kit for 250cc benzhou 2007 with proper specifications for piston
You can try contacting the manufacturer of the scooter, Benzhou, to see if they have a rebuild kit available for the 2007 250cc model. You can also check with local scooter or motorcycle shops to see if they carry rebuild kits for that specific scooter model. Additionally, you can try searching online for aftermarket rebuild kits for the Benzhou 250cc scooter. Be sure to specify the year and model of your scooter when searching to ensure you get the proper specifications for the piston.
1/22/2023 4:32:44 AM •
Motorcycles
•
Answered
on Jan 22, 2023
What is the torque specs for a 97 Harley electro glide?
The torque specifications for a 1997 Harley-Davidson Electra Glide will vary depending on the specific components of the motorcycle. Here are some general torque specifications for a 1997 Harley-Davidson Electra Glide:
- Engine oil drain plug: 25-35 ft-lbs
- Transmission drain plug: 25-35 ft-lbs
- Transmission fill plug: 25-35 ft-lbs
- Primary cover bolts: 25-35 ft-lbs
- Clutch hub nut: 60-80 ft-lbs
- Timing cover bolts: 25-35 ft-lbs
- Cylinder head bolts: 80-100 ft-lbs
- Rocker arm cover bolts: 25-35 ft-lbs
- Rocker arm adjusting screw lock nut: 25-35 ft-lbs
- Rocker arm pivot shaft nut: 25-35 ft-lbs
- Pushrod cover bolts: 25-35 ft-lbs
- Pushrod tube clamp bolt: 25-35 ft-lbs
- Oil pump cover bolts: 25-35 ft-lbs
- Oil pump drive gear nut: 25-35 ft-lbs
- Oil filter adapter cover bolts: 25-35 ft-lbs
- Oil cooler lines: 25-35 ft-lbs
- Oil pressure sender switch: 25-35 ft-lbs
- Oil pressure relief valve: 25-35 ft-lbs
- Oil pressure switch: 25-35 ft-lbs
- Oil pressure gauge sender: 25-35 ft-lbs
Please note that these are general torque specifications and it's recommended to check the service manual for your specific 1997 Harley-Davidson Electra Glide for the most accurate information. Additionally, it's always recommended to consult a professional mechanic or a Harley-Davidson dealer for advice, even if you're a seasoned motorcycle mechanic.
1/20/2023 10:18:41 AM •
Motorcycles
•
Answered
on Jan 20, 2023
How to bench sync 1977 GS750 throttle slide height
The baseline throttle slide height for a Suzuki GS750 motorcycle should be set so that the slides are fully closed when the throttle grip is in the closed position. This means that when you twist the grip fully counterclockwise to the stop, the slides should be flush with the carburetor body.
To adjust the throttle slide height, you will need to remove the carburetors from the bike and use a feeler gauge to measure the gap between the bottom of the slide and the carburetor body.
It is important to make sure the throttle cables are properly adjusted before setting the throttle slide height. The throttle cables should be adjusted so that the throttle grip moves the slides smoothly and the grip is in the closed position when the slides are fully closed.
It is also important to keep in mind that the carburetors on a Suzuki GS750 motorcycle should be synchronized after adjusting the throttle slide height. This ensures that all carburetors open and close at the same time and at the same rate, which is necessary for proper engine performance.
Please note that this is a general explanation and the specific process may vary depending on the year or model of your Suzuki GS750 motorcycle. It's recommended to consult the service manual for your specific bike for detailed instructions on adjusting the throttle slide height and synchronizing the carburetors.
1/20/2023 10:17:18 AM •
Motorcycles
•
Answered
on Jan 20, 2023
My piaggo zip 70s kit will not start
There are several potential reasons why your Piaggio Zip 70s scooter may not be starting. Some common causes include:
- Dead battery: Make sure that the battery is charged and in good working condition.
- Faulty spark plug: Check the spark plug and replace it if it is dirty or worn.
- Clogged fuel filter: A clogged fuel filter can prevent fuel from reaching the engine.
- Air filter: The air filter can be clogged, restricting airflow to the engine.
- Poor compression: If the compression in the engine is low, it may not start.
It is difficult to determine the exact cause without more information or a proper diagnosis. The best course of action would be to refer to the manufacturer's manual or seek help from a qualified mechanic who can inspect and diagnose the problem.
1/17/2023 3:53:54 PM •
Motorcycles
•
Answered
on Jan 17, 2023
Why will my 2006 gsx750f not start
There can be several reasons why your 2006 Suzuki GSX750F may not start. Here are a few common causes and things you can check:
- Battery: Make sure the battery is fully charged and connected properly. A weak or dead battery can prevent the motorcycle from starting.
- Fuel: Make sure there is enough fuel in the tank and that the fuel valve is in the "on" position. A clogged fuel filter or a malfunctioning fuel pump can also prevent the motorcycle from starting.
- Spark plugs: Check the spark plugs to make sure they are clean and in good condition. Dirty or worn spark plugs can prevent the motorcycle from starting.
- Ignition: Check the ignition switch, starter relay, and starter motor to make sure they are working properly. A malfunctioning ignition switch or starter relay can prevent the motorcycle from starting.
- Air filter: Check the air filter to make sure it is clean and in good condition. A clogged air filter can restrict airflow to the engine and prevent it from starting.
- Timing: Check the timing of the engine. A timing problem can prevent the motorcycle from starting.
It's important to keep in mind that these are just a few common causes and that there may be other issues that are preventing your 2006 Suzuki GSX750F from starting. It's best to take it to a qualified mechanic if you're unable to diagnose the issue.
It's also important to note that some of these steps require a certain level of mechanical knowledge and experience. If you're not comfortable with checking these items, it's best to consult a professional mechanic.
if i was able to help my cashapp $ralphpapi thank you have a blessing day
1/15/2023 8:29:44 AM •
Motorcycles
•
Answered
on Jan 15, 2023
1977 GS750 Throttle slide height
When adjusting the throttle slide height on a 1977 GS750, the manual states that the slides should be set at .5-1mm above the top of the carburetor when they are opened wide open. The correct position to set the slide height is on the airbox side of the carburetor slide.
When the throttle slide is set too high on the engine side, it can cause the bike to idle high, as you mentioned. This is because the slide is not allowing enough air to enter the carburetor, which can cause the engine to run rich.
To adjust the throttle slide height, you will need to follow these steps:
- Remove the air filter and carburetor top covers to access the slides.
- Using a feeler gauge, measure the distance between the top of the slide and the top of the carburetor.
- If the distance is greater than .5-1mm, adjust the slide height by turning the adjustment screw located on the airbox side of the carburetor slide.
- Once the slide height is set, replace the air filter and carburetor top covers.
- Start the engine and check the idle speed. If it is still high, repeat the above steps until the correct slide height is achieved.
It's important to note that when adjusting the slide height, you will also need to make sure that the throttle cable is adjusted correctly, as this can also affect the idle speed. Additionally, when making any adjustments to the carburetor, it's best to have a professional mechanic to check it, as it could cause other issues if not set correctly.
1/14/2023 11:47:25 PM •
Motorcycles
•
Answered
on Jan 14, 2023
Aeon Mini Kolt 50cc - cuts out when engine gets hot. What is wrong?
Check the compression on your engine take that off clean the valves is not much to an engine like that the engines cut down when it gets hot so it doesn't seize up make sure he got oil added to could be the O-rings but the compression tests would tell you that is not the race I checked the valves
1/10/2023 4:10:04 PM •
Motorcycles
•
Answered
on Jan 10, 2023
Not finding what you are looking for?