Top 20 2000 Husaberg Fe 600 - Page 5 Questions & Answers

Your manual will show you what is what. If you haven't got a manual, they can be found on the gargler. Just google your model and include owners manual

It doesn't make any difference unless on a motorcycle in which it is closer to the spedometer and more convenient to mount.

Hello Scott The Raja Akeem Akhter Artificial Intelligence Answer Bot doesn't do follow-ups. It guesses answers and there may not be a sensor. One thing he is right about is that calling a professional is the best solution. There is some help in this link https://www.google.com/search?q=Carrier+comfort+pro+APU+fault+code+low+oil+pressure More help on the sensor https://www.google.com/search?q=carrier+comfort+pro+apu+low+oil+pressure+sensor+location ..

videos showing how https://www.google.com/search?q=replace+broken+final+drive+belt+for+a+2003+softail

If your Lexmoto ZSX-R 125cc is not starting and you're experiencing issues with the engine light and gear display, here are some troubleshooting steps you can take:

1. Check the fuses: Inspect the fuse box of your motorcycle and verify if any fuses related to the ignition system or engine control are blown. Replace any blown fuses with new ones of the correct rating.
2. Check the battery connections: Even if the lights are working, there could be a loose or corroded connection at the battery terminals. Ensure the battery terminals are clean, tight, and free from corrosion. Consider using a multimeter to measure the battery voltage and ensure it is within the recommended range.
3. Examine the wiring: Inspect the wiring harness for any loose or damaged connections, particularly around the ignition system and engine control. Look for frayed wires, loose plugs, or disconnected connectors. Repair or replace any damaged wiring as necessary.
4. Test the ignition switch: The clicking sound you hear may indicate that power is reaching the starter solenoid, but it doesn't necessarily guarantee that the ignition switch itself is functioning correctly. Try cleaning the ignition switch contacts or consider replacing the switch if necessary.
5. Check the side stand switch and clutch switch: Some motorcycles have safety switches on the side stand or clutch lever that prevent the engine from starting if engaged. Ensure the side stand is up, and if there is a clutch switch, make sure it is properly engaged when attempting to start the bike.
6. Inspect the spark plug: Although you mentioned that the spark plug was cleaned, it's worth double-checking its condition. Remove the spark plug and examine it for fouling or wear. If necessary, replace the spark plug with a new one of the correct specification.
7. Consider the possibility of a sensor or ECU issue: If the engine light is on and the gear display is not functioning correctly, there may be a problem with a sensor or the engine control unit (ECU). It might be necessary to have the motorcycle diagnosed using specialized diagnostic tools or by a professional mechanic familiar with Lexmoto motorcycles.

If you've exhausted these troubleshooting steps and are still unable to resolve the issue, it's recommended to consult a qualified motorcycle mechanic or contact Lexmoto's customer support for further assistance. They will have more specific knowledge and resources to help diagnose and repair the problem.

If you have already replaced the voltage regulator and checked the grounding wire, the next step would be to check the circuit breaker. Here's how you can check the circuit breaker:

1. Turn off the generator and unplug all appliances connected to it.
2. Open the generator's control panel to access the circuit breaker.
3. Check the circuit breaker for any signs of damage, such as burnt or melted parts, or loose connections.
4. If there is no visible damage, use a multimeter to test the circuit breaker. Set the multimeter to measure resistance (ohms) and touch the probes to the terminals of the circuit breaker. If the circuit breaker is working properly, the multimeter should show zero resistance.
5. If the circuit breaker is faulty, it will need to be replaced. You can contact the manufacturer or a qualified technician for assistance with replacing the circuit breaker.

It is also possible that the generator's stator or rotor has been damaged, which could be causing the lack of AC output. In this case, you may need to contact the manufacturer or a qualified technician for further diagnosis and repair. Please note that working with electricity can be dangerous and should only be attempted by those with the appropriate training and experience. If you are not comfortable performing these checks yourself, it is recommended to seek the assistance of a qualified technician.

Check that it is running on both cylinders. If plugs are fresh, pull them and compare. If one still looks like new out of the box then that cylinder is not firing. Or if you have an infrared temperature probe, check the exhaust temp at each pipe is the same.

Are you sure those numbers are correct? Trouble codes normally start with a 0, 1 or a 2. Was there any other information with the code. Some Harley models use 3 or 4 letter codes as well to refer to the system where the issue is.

Recheck all your cable connections to the carb are correct and the cable routes are not kinked. This can sometimes cause tight spots on the cable making the choke cable stick and not work correctly. As long as you didn't change anything on the original carb when you took it off your lean/rich mixture should be correct. Is this happening as you're pushing the choke Off or does it happen when you pull it back out to the On position when the engine is already warm? If it's happening when you trying to turn the choke Off it is often a sign the fuel jets on the carb are clogged or dirty, starving the engine of fuel. Get all the jets cleaned by someone who knows what they are doing and see if that helps The choke is simply a flap, that when you pull the choke on, starves the carb of air creating a deliberate 'rich' fuel mixture. This sounds like turning the choke off starves the carb of that extra fuel and stalls the engine.

The 'fuel mix' screw is only for tickover as the main jet is closed at that point. The other screw is for tickover speed. If you are not experienced in setting up twin carbs, you will have fun. Screw both mixture screws in whilst counting the turns and part of turn. Remember the turns in case you get mixed up. Unscrew them both 2 1/4 turns. That is a good starting point. With a hose pipe, place one end near your ear and the other to listen at each carbourettor. You are listening for even vacuum sounds from both. With the tickover screw, that will be obvious but as I say, what you do to one must be done to the other or it will tickover rough.

It sounds like you have done a lot of troubleshooting already, but have you checked the wiring harness for any breaks or shorts? It is possible that the wiring harness is damaged and not allowing the spark to reach the plugs. If you have checked all of the components and wiring and still can't find the issue, then it may be time to take it to a professional mechanic to have them look into it further.

There are 10,000 Chinese motors, and you don't say what it is on. It is in the Motorcycles category, but posters often use the category that Fixya offers. Motorcycle, Riding Mower, Power Washer, Scooter, Generators, ATV, all have motors. The way to solve is from the vehicle it is in. Google year make model wiring diagram https://www.google.com/search?q=Chinese+motor+with+10+wires ..

The engine must be in the upright position. Preferably on the centre full stand not side or kick stand to keep it upright.

The starter on a Honda VTX 1800 motorcycle is located on the right side of the engine, beneath the chrome engine cover. You will need to remove the cover to access the starter motor. The starter motor is a small cylindrical unit with wires running to it. It is responsible for turning the engine over when you press the starter button. If you are having trouble starting your VTX 1800, it is possible that there is an issue with the starter motor, but there could be other causes as well, such as a dead battery or a faulty ignition switch.

The mixture screw on your Majesty 125 2007 is located on the left side of the carburetor, just below the air filter cover.

The first thing you need is a speed sensor. That is usually found on the output shaft from the gearbox, before it goes to the rear wheel. Once you have that, wire it up and then callibrate the speedo to the turns ratio of the speed sensor. Or, use a GPS. More accurate and convenient to see where you are going.

The fuel hose it the one that comes from the fuel tank and the vent hose disappears below the engine and it open at the bottom. https://haynes.com/en-us/scooter-manuals/jinlun ..

Clean the carbs and fit new seals. E20 fuel ruins rubber seals!

• all cars or trucks or MOTORCYCLES.W/ (MANUAL BOX , MANUAL CLUTCH)
• WE MAKE SURE CLUTCH IS WORKING FIRST. AND DOES NOT SLIP AND OVER-REV NOR DRAG. THEN COMES
• THE BOX., THE SHIFT FORKS AND DRUM INSIDE ARE PROBABLY GOOD IF OIL LUBE IS NEVER ALLOWED TO DRY OR BAD.
• NEXT IS THE SHIFT LEVER ADJUSTED WRONG.
• GET THE BIKE SERVICED, IN A REAL SHOP, CLUTCH FIRST.
• IS CLUTCH CABLE DRIVE OR HYDRAULIC, IS THE MASTER CYLINDER NEAR DRY ON THE LATER????????

ONLY 1 QUESTION , DO YOU ALWAYS USE THE CLUTCH TO SHIFT IF NOT THE GEARS ARE A WRECK. BUY THE SERVICE MANUAL AND SEE ALL PART AND WHAT MUST BE DONE TO GAIN ACCESS TO THEM ALL.