2000 Husaberg Fe 600 - Answered Questions & Fixed issues

Hi, Cheyneweathe and the usual suspects are:
1. Fuel tank empty.
2. The fuel tank has old dead gas.
3. Fuel tank bottom contaminated with ethanol sludge, dirt, water, rust, etc.
4. Fuel supply valve/petcock turned off.
5. Fouled spark plugs.
6. Engine flooded as a result of overuse of the choke.
7. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
8. Fuel valve/petcock or filter clogged.
9. Fuel line to carburetor or throttle body pinched, kinked or blocked.
10. Carburetor float stuck.
11. Fuel injectors clogged.
12. Fuel injectors stuck open.
13. Quick disconnect check ball stuck.
14. Compression below 75 PSI.
15. A stuck-bent-burnt valve.
16. Improper valve clearance (too tight)
17. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a cursory reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
18. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
19. Loose or corroded wire connection at the coil or plug between ignition sensor and ECM module.
20. Spark plug cables in bad condition and shorting check for spark leakage in the dark, cable connections are loose or connected to the wrong cylinders.
21. Ignition timing incorrect due to a faulty ignition coil, ignition module or MAP, CMP, CKP, O2, TPS, ETP, IAC sensors.
22. Faulty neutral, clutch, kickstand safety switch.
23. Faulty fuel pump or fuse or relay.
24. Faulty or corroded run/stop switch.
25. Tilt sensor needs a reset.
26. Security system not disarming alarm needs a reset.
27. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
What To Do If Your Motorcycle Doesn Start

2000 Husaberg Fe... | Answered on Jun 13, 2019 | 64 views

you need a micrometere or vernier caliper to measure how thick they are that how you tell how worn the clutch is. the manual will list the specificational limit (how thin you should allow them to get and how do the basket and innser hub looks like). if they have small teeth on them they are worn.,

2000 Husaberg Fe... | Answered on Nov 10, 2008 | 71 views

ProClean is good stuff but not worth the money. The only reason I had it was because I won a create of it at our clubs Supercross race it's too expensive in my opinion. I buy 40 litre containers of stuff called TFR which stands for Traffic Film Remover, it basically is a detergent like ProClean, Simple Green and all the others, only it costs a fraction of the price and isn't deluted. This means you can delute it to your own strength for different causes. You can see it removing dirt as you watch, like someone said above. You can not use it pure on the bike however, it will make alloy parts go dull - as my buddy found out lol. ,,,

2000 Husaberg Fe... | Answered on Nov 10, 2008 | 95 views

i always just put some on the o-ring before i put it back in but no you dont need to have oil on it,

2000 Husaberg Fe... | Answered on Nov 10, 2008 | 140 views

depends on what material is stained.. Aluminium stains can be very tricky to get clean if not impossible...some cleaners will also cause a orange/reddish stain wich will not come out unless you use some harsh chemicals to get them out. problem is it's hard to get to those chemicals. IF you happen to have a truck wash nearby where they wash the big trucks (18 wheelers)take your parts there and tell them to use some brightener on it it's a chemical that really cleans aluminium.it may cost you a little bit of money but that stuff really works and i haven't been able to find that stuff for private sale anywhere. the number 2 reasons for stains on the bike are : 1) waiting to long to wash the bike some types of sand/mud especially the red dirt we have down south here will stain a bike if you leave it on the bike not only that it dries as hard as concrete and is very difficult to remove , so was your bike ASAP. 2) washing chemicals. Some chemicals / soaps when they are left too long on aluminium will leave stains as it reacts with the aluminium , these stains are almost impossible to get out. ,,,

2000 Husaberg Fe... | Answered on Nov 10, 2008 | 171 views

and had the bike souped for it. Anyway the throttle is SUPER touchy.. You breath on it and it takes off.. Because of this I ended up dumpin it 30 min after I got on..haha... My question is is there a way to stiffen up the throttle so that i have to crank the grip harder to give it gas? I am very inexperienced, and when it took off, i tensed up, hittin the throttle even harder. I know i will appreciate the the responsiveness when I get more experience, but i dont want to die in the process..lol.. thanks for you help! ,UYou need to learn to hold on to the bike with your legs, so you aren't pulling on the bars during acceleraion. The throttles are supposed to be easy to turn, so that it will snap completely closed when you let off. You can replace the throttle cam (the part that the cable attaches to) with a slower-opening unit that will give you more control. The amount you have to turn the throttle from closed to full-open will stay thesame, but it will open slower in the first half of the throttle pull, keeping you from getting such an abrupt surge of power. Once you get a little more time on the bike, you won't have this issue any longer. You will learn proper throttle control, and your wrist will get used to the throttle pull. ,,,

2000 Husaberg Fe... | Answered on Nov 10, 2008 | 124 views

Hi, Anonymous and the usual suspects are:
1. Fuel cap or fuel tank is not venting properly.
2. Fuel filter clogged.
3. Fuel line pinched or kinked.
4. Vacuum line from the petcock to intake manifold cracked.
5. Float needle and seat sticking.
6. Float level too low.
7. Carburetor bowl vent line clogged/blocked/pinched.
8. Idle adjusting screw set too low.
9. Air/fuel mixture screw set too lean.
10. Idle port, transfer ports, slow air jet clogged.
11. Slow fuel jet clogged.
12. Faulty fuel pump.
13. Faulty auto choke or wiring connection.
For more information about your issue and valuable "Free" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
WHY your motorcycle only runs on CHOKE

Husaberg... | Answered on Jun 13, 2019 | 40 views

Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Husaberg, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.

Husaberg... | Answered on Jun 13, 2019 | 46 views

The main fuse protects all power consumers of the vehicle. It is located in the starter relay housing under the air filter box lid. (A spare fuse is located in the starter relay)

The fuse box containing the fuses of individual power consumers is located under the seat

Husaberg... | Answered on Feb 26, 2017 | 50 views

Hi, Pete and the usual suspects are:
1. Severely drained or faulty battery.
2. Faulty regulator/rectifier or high output coil.
3. Faulty power valve, solenoid or installation.
4. Clogged air filter or exhaust.
5. Cracked or incorrect float level.
6. Float needle is not seating.
7. Faulty reed valve.
For more information about your question please visit the website below. Good luck and have a nice day.
HUSABERG Pure Enduro Service

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Husaberg... | Answered on Nov 11, 2015 | 66 views

Its a long shot, but try Youtube.
They have tons of DIY videos.

Husaberg... | Answered on Jan 08, 2015 | 62 views

Basically the only way water can get in the oil is if there is a corrosion hole in the housing behind the pump impellor. Water pumps have only 1 seal and if that leaks water will drain from a hole in the pump housing under neath the pump.

Husaberg... | Answered on Mar 11, 2013 | 286 views

Assuming you mean a Digitech GNX2 floor effects pedal, go to the Digitech site, search GNX2 and select support: Manuals


The Re-Categorize link in FixYa is broken so I can't put it in a better category. If it is not a Digitech pedal, could you please Comment with the full make and model of what you are looking for.

Motorcycles | Answered 13 hours ago | 12 views

Hi, Anonymous the vast majority of service, parts fiche, and owners manuals on the internet are "FREE" to download and all service manuals contain wiring diagrams in the back pages. The rest usually charge a modest fee of $15 and there is a handful of obscure, rare, obsolete, and very old models that are no longer or never were available and some were never printed in English. The Indian and Philippine markets are usually in E-book format only, for these rare occasions I shall look on eBay and find the cheapest one available. Most of the manuals will cover your exact make, model, and year otherwise one will be provided that comes as close as possible to your bike and will have most of the same info that an exact manual would have. If there is no $ sign after the manual link it is free to download.
To download your manual for viewing or printing please click on the blue links below. Good luck and have a wonderful day.

Motorcycles | Answered on Nov 12, 2019 | 36 views


Motorcycles | Answered on Nov 12, 2019 | 24 views


Motorcycles | Answered on Nov 12, 2019 | 20 views

take the carb off and clean all the jets, needles and float.

In future please state year make and model rather than a '4af'.

Motorcycles | Answered on Nov 10, 2019 | 16 views

Sorry but google is your friend. All I had to do is search for Model D2275 Tool Stand pdf and the first search results came up with a pdf file for the manual.


Motorcycles | Answered on Nov 10, 2019 | 26 views


Motorcycles | Answered on Nov 09, 2019 | 18 views

Not finding what you are looking for?
2000 Husaberg Fe 600 Logo

10 questions posted

Ask a Question

Usually answered in minutes!

Top Husaberg Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5962 Answers


Level 3 Expert

85206 Answers


Level 3 Expert

1562 Answers

Are you a Husaberg Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides