20 Most Recent 2003 Husaberg Fe 400 E Questions & Answers


if nothing else you shuld have a check bolt on the side of the left or right case

2003 Husaberg Fe... | Answered on Jun 08, 2012


Assuming the bike runs well and this is just a kicking technique problem.
push the kick starter slowly until you get to the hard spot(TDC), pull the decomp lever, and push the kicker a little to get past top dead centre, then release decomp and give it a decent kick, should never kick back

2003 Husaberg Fe... | Answered on Apr 15, 2010


all it needs is fresh engine oil and run a spaner around it,,,just incase any thing is about to "drop off"

2003 Husaberg Fe... | Answered on Feb 06, 2010


ProClean is good stuff but not worth the money. The only reason I had it was because I won a create of it at our clubs Supercross race it's too expensive in my opinion. I buy 40 litre containers of stuff called TFR which stands for Traffic Film Remover, it basically is a detergent like ProClean, Simple Green and all the others, only it costs a fraction of the price and isn't deluted. This means you can delute it to your own strength for different causes. You can see it removing dirt as you watch, like someone said above. You can not use it pure on the bike however, it will make alloy parts go dull - as my buddy found out lol. ,,,

2003 Husaberg Fe... | Answered on Nov 10, 2008


Put it up on your stand lossen the axel and remove the bolt on the bottom of the shock. Then tighten your chain and lift your swingarm up until its horizontal with the ground, then the chain should have almost no play. Not completely tight, but almost no play. Tighten the axel, and the bolt on the shock, and your set,,,

2003 Husaberg Fe... | Answered on Nov 10, 2008


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Husaberg, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.ultimatespecs.com/motorcycles-specs/honda/husaberg-fe-400-e-2003
http://husaberg.org/mechanical/19634-oil-level.html
https://www.emanualonline.com/Motorbikes/Husaberg/FE-Models.htm
http://www.cyclebuy.com/husaberg/parts.htm
Husaberg 400 User Manual

Husaberg Fe 400... | Answered on Jun 13, 2019


Hi, Barry it's nonadjustable for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Husaberg, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.topspeed.com/motorcycles/motorcycle-reviews/husaberg/2013-husaberg-fe-350-ar148843.html
KTM 350 Valve Adjustment And Camshaft Swap
http://www.datamanagement-le-blog.com/fe350_service_manual_download.pdf
https://www.rockymountainatvmc.com/Parts-Finder/11057/2013-HUSABERG-FE-350
https://paitandacent.files.wordpress.com/2015/08/husaberg-fe-350-owners-manual.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Husaberg Fe 400... | Answered on Nov 25, 2017


Hi, Anonymous and the usual suspects are:
1. Fuel cap or fuel tank is not venting properly.
2. Fuel filter clogged.
3. Fuel line pinched or kinked.
4. Vacuum line from the petcock to intake manifold cracked.
5. Float needle and seat sticking.
6. Float level too low.
7. Carburetor bowl vent line clogged/blocked/pinched.
8. Idle adjusting screw set too low.
9. Air/fuel mixture screw set too lean.
10. Idle port, transfer ports, slow air jet clogged.
11. Slow fuel jet clogged.
12. Faulty fuel pump.
13. Faulty auto choke or wiring connection.
For more information about your issue and valuable "Free" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://husaberg.org/fuel/5956-only-runs-choke-any-hints.html
WHY your motorcycle only runs on CHOKE
https://www.repair-manuals.eu/cat/motorcycle_repair_workshop_manuals/repair_manuals_husaberg
http://www.cyclebuy.com/husaberg/parts.htm
https://www.manualslib.com/manual/813892/Husaberg-E-400-E.html#product-FC%20550/4

Husaberg... | Answered on Jun 13, 2019


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Husaberg, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?q=Replace+the+battery+2002+husaberg+470-fxe&source=lnms&tbm=isch&sa=X&ved=0ahUKEwjHooyGkObiAhXqqFkKHcIWB3kQ_AUIESgC&biw=1440&bih=757
http://husaberg.org/electrical/9274-new-owner-fx-470-2002-battery-replacement-question.html
http://husaberg.org/mechanical/11215-workshop-manual.html
http://www.cyclebuy.com/husaberg/parts.htm
https://www.manualslib.com/manual/640214/Husaberg-05.html

Husaberg... | Answered on Jun 13, 2019


The main fuse protects all power consumers of the vehicle. It is located in the starter relay housing under the air filter box lid. (A spare fuse is located in the starter relay)

The fuse box containing the fuses of individual power consumers is located under the seat

Husaberg... | Answered on Feb 26, 2017


Hi, Pete and the usual suspects are:
1. Severely drained or faulty battery.
2. Faulty regulator/rectifier or high output coil.
3. Faulty power valve, solenoid or installation.
4. Clogged air filter or exhaust.
5. Cracked or incorrect float level.
6. Float needle is not seating.
7. Faulty reed valve.
For more information about your question please visit the website below. Good luck and have a nice day.
HUSABERG Pure Enduro Service

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Husaberg... | Answered on Nov 11, 2015


Its a long shot, but try Youtube.
They have tons of DIY videos.

Husaberg... | Answered on Jan 08, 2015


Basically the only way water can get in the oil is if there is a corrosion hole in the housing behind the pump impellor. Water pumps have only 1 seal and if that leaks water will drain from a hole in the pump housing under neath the pump.

Husaberg... | Answered on Mar 11, 2013


Casey... if you have turned your adjustment screw that much...there is no way you should have ever turned it that much...If it were me.. I would take it to a Suzuki professional and let them replace the fluid and set the adj. screws back to stock,,,you have to be a good rider to really notice a lot of difference.. and have a good sticky front tire!! Stop fooling with it!!

Motorcycles | Answered 3 days ago


What metal beams.. what are the metal beams used for Good quality powder coat last a long time... paint might..

Motorcycles | Answered 3 days ago


IF the charger is sealed you won't be able to fix it... just buy a new one...
If you do get in it.. finding the correct parts will be your problem..

Motorcycles | Answered 3 days ago


Hi, Richard for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere zero $ you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?q=Fuse+box+location+2005+Suzuki+Bandit+1200S&tbm=isch&source=univ&sa=X&ved=2ahUKEwj_7eD1qaTmAhWR2FkKHULmCL0QsAR6BAgJEAE&biw=1440&bih=757
https://www.youtube.com/watch?v=RZ2RrR-tbYk
https://www.manualslib.com/manual/1053286/Suzuki-2005-Gsf1200.html
https://www.partsfish.com/page/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki/

Motorcycles | Answered on Dec 07, 2019


Fuel filter dirty? This could be a problem the '85 LTD and the '86 SEI. The fuel filter for those machines are different than the rest. They are for the pressurized fuel system and are a bit expensive. Don't know if mother Honda still has them.

Motorcycles | Answered on Dec 04, 2019

Not finding what you are looking for?
2003 Husaberg Fe 400 E Logo

9 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Husaberg Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5971 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Strech
Strech

Level 3 Expert

1562 Answers

Are you a Husaberg Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Fe 400 E Husaberg

  • Fe 400 E Husaberg

Most Popular Question

shes start

  • Motorcycles
Loading...