2003 Husaberg FX 650 e - Answered Questions & Fixed issues
Oil check
There are usually two methods to check the oil. One is a dipstick and the other is a sight-glass. You should have one or the other somewhere on the side of the engine crankcase. It should be fairly obvious and not require the removal of any body panels. If you can't find a dipstick in the side of the crankcase you will need to get down on your hands and knees and have a look for a sight-glass instead. This will be like a tiny window with a gauge against which you can check the level.
Battery
If your bike was exposed to very hot or very cold weather for awhile that would be sufficient to weaken your battery. Heat and cold can drain a battery of power so it's important to check the battery hydro levels frequently and run a trickle charge during off-season.,,,
Chain
Put it up on your stand lossen the axel and remove the bolt on the bottom of the shock.
Then tighten your chain and lift your swingarm up until its horizontal with the ground, then the chain should have almost no play. Not completely tight, but almost no play.
Tighten the axel, and the bolt on the shock, and your set,,,
Damage check
This would depend on how you drop the bike. If it just falls over you would check everything on that side that could be damaged. It would be the same for a low speed drop. However if the bike not only gets droped but hits something while sliding you might bend the frame or suspension or damage wheels or controls.,,,
Where are the fuses on husaberg 450fe 2008 ?
The main fuse protects all power consumers of the vehicle. It is located in the starter relay housing under the air filter box lid. (A spare fuse is located in the starter relay)
The fuse box containing the fuses of individual power consumers is located under the seat
2/26/2017 10:43:29 PM •
Husaberg...
•
Answered
on Feb 26, 2017
•
148 views
Water pump seals
Basically the only way water can get in the oil is if there is a corrosion hole in the housing behind the pump impellor. Water pumps have only 1 seal and if that leaks water will drain from a hole in the pump housing under neath the pump.
3/11/2013 4:52:54 AM •
Husaberg...
•
Answered
on Mar 11, 2013
•
431 views
Need circuit diagram for ARLEC 15e 6-24Volt 15Amp Electronic battery charger OR their later model BC58
I can't find a diagram.
The small potentiometer on the control board likely serves as an adjustable component to fine-tune specific parameters. Here are some possibilities:
Voltage Regulation:
The potentiometer might control the output voltage. By adjusting it, you can set the desired charging voltage for different battery types (e.g., 6V or 12V).
Current Limit Adjustment:
It could be used to set the maximum charging current. Adjusting the potentiometer allows you to limit the charging current based on the battery's capacity and condition.
Sensitivity or Threshold:
Some potentiometers act as sensitivity controls. For example, it might adjust the threshold at which the charger switches between charging and maintenance modes.
Setting the Potentiometer:
Without the specific circuit diagram or detailed information about your charger, I recommend the following general steps:
Observe the Potentiometer:
Identify the potentiometer on the control board. Note its position and any markings (if present).
Consult the User Manual:
Check the user manual or operating instructions. It might provide guidance on adjusting the potentiometer.
Trial and Error:
If no specific instructions are available, start with the potentiometer set to its mid-position.
Gradually adjust it while monitoring the charger's behavior (e.g., charging current, voltage).
Observe how the charger responds to changes in the potentiometer setting.
Fine-tune it based on your specific battery type and desired charging characteristics.
Remember that precise adjustments depend on the charger's design and the battery you're charging.
4/18/2024 7:22:52 PM •
Motorcycles
•
Answered
17 hours ago
•
24 views
What is the length of lift cables on a 1993 model 2693 hilo camper and any info on what after market part to use ? thanks
The lift cables on a 1993 model 2693 Hilo camper are 30 feet,2 3/4 inches long and fit the standard height lift of 11 feet 8 inches high to the top of the overhead. The lift uses two cables. According to a Hi- Lo camper travel trailer forum, cable replacement is basically the same on all years and models, with the main difference being the length of the cables from model to model. You can use a cable cut chart to find what cable length you need for your camper, and you'll need to know your year, model name, and box (body) length: Lift cables typically wear out after three to five years, so it's important to replace them as needed and keep them regularly maintained.
4/12/2024 1:26:15 AM •
Motorcycles
•
Answered
on Apr 12, 2024
•
17 views
Not finding what you are looking for?