20 Most Recent 2005 Hyosung GT 650 R Questions & Answers


Hi, Ross and the usual suspects are:
1. Low coolant level.
2. Restricted radiator air flow.
3. Faulty thermostat.
4. Coolant pump or fans inoperative.
5. Vent hose crimped.
6. The air in the coolant and needs bleeding.
7. Engine idling too long or bike moving too slow.
8. Coolant too old needs to be replaced.
9. Faulty temperature sensor, wiring or connector.
10. Radiator veins clogged or corroded needs repair
11. Cooling system leak.
12. Ignition timing retarded.
13. Spark plug heat range too high.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://korider.com/index.php?topic=23356.0
Overheating Help troubleshoot my bike
HYOSUNG GT 650 Service Manual
https://alpha-sports.com/hyosung_parts.htm
https://www.manualslib.com/manual/810064/Hyosung-Gt650.html#product-GT650%20R%20Ei

2005 Hyosung GT... | Answered on Jun 22, 2019


Hi, John for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Hyosung, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?sa=X&q=Fuel+and+vacuum+line+routing+2005+Hyosung+GT650R&tbm=isch&source=univ&ved=2ahUKEwjauaOm2PLiAhWpxFkKHSRSD-IQsAR6BAgBEAE&biw=1440&bih=757
Vacuum and fuel line routing
HYOSUNG GT 650 Service Manual
https://alpha-sports.com/hyosung_parts.htm
HYOSUNG GT 650 Manual

2005 Hyosung GT... | Answered on Jun 18, 2019


Hi, Jd145505 and the usual suspects are:
1. Contaminated or faulty speed sensor.
2. Faulty turn signal module.
3. Corroded, broken or loose connector pins/sockets in the wire harness between the speedometer and the ECM or TSSM and the sensor.
4. The speedometer unit has failed.
5. Speedometer instrument fuse has blown.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://korider.com/index.php?topic=20334.0
How to Fix Motorcycle Speedometer SpeedoDRD
HYOSUNG GT 650 Service Manual
https://alpha-sports.com/hyosung_parts.htm
HYOSUNG GT 650 Manual

2005 Hyosung GT... | Answered on Jun 18, 2019


Hi, Sam2nd5190 how long is a piece of string? the answer to this question is way above my pay grade for this situation, I would call or visit my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.twobros.com/pages/faq-exhaust-two-brothers-racing
https://www.twobros.com/products/hyosung-gt650-2007-2015-exhaust
HYOSUNG GT 650 Service Manual
https://alpha-sports.com/hyosung_parts.htm
HYOSUNG GT 650 Manual

2005 Hyosung GT... | Answered on Jun 18, 2019


Hi, Nico I would love to help you with your engine or chassis noise but I just loaned my brand new pair of listening ears to your local dealer's chief technician so he could take your bike for a test ride and give you his professional opinion and estimate about your noise and repair cost. If you are a little short on "DRACHMA" and a Dealership is not on your list of fun places to visit then perhaps the list below will help soothe your worried mind so you can make an informed decision.
1. Bearings---SCREECH---WHINE
2. Belts---CHIRP
3. Brake Rotors---BUZZ
4. Cam Chains---CLICKIT
5. Clutches---CHATTER
6. Cylinders---PING
7. Fairing Panels---WHISTLE
8. Fenders---SCRAPE
9. Fronk Forks---Plunk
10. Fuel pumps---WHIRR
11. Gears---WHINE
12. Head Gasket---HISS
13. Hydraulic Lifters---TAP
14. Instrument Clusters---BUZZING
15. Kick Starter---GRINDS
16. Pistons---SLAP
17. Power Valves---CLINK& RATTLE
18. Radiators---GURGLE
19. Rear Chains---RATTLE
20. Rear Shocks---SQUEAK
21. Relays---CLICK&BUZZ
22. Shaft Drives---WHIRR
23. Shifting Trans---CLUNK
24. Solid Lifters---TICK
25. Speedometers---bzzz
26. Starters---CLICK
27. Rods Go---KNOCK-KNOCK---who's there, it's me "*****"
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://korider.com/index.php?topic=16968.0
https://www.kiwibiker.co.nz/forums/showthread.php/104470-Engine-rattle
HYOSUNG GT 650 Service Manual
https://alpha-sports.com/hyosung_parts.htm
HYOSUNG GT 650 Manual

2005 Hyosung GT... | Answered on Jun 18, 2019


Hi, Ross and the usual suspects are:
1. Improper clutch adjustment or not disengaging.
2. Bent shift shaft.
3. Shift fork bent or seized.
4. Gear seized on the shaft.
5. Gear positioning lever binding.
6. Shift return springs weak or broken.
7. Shift return spring pin loose
8. Shift mechanism arm spring is broken.
9. Shift mechanism arm is broken.
10. Shift drum is broken.
11. Shift lever loose on the shift shaft.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.kiwibiker.co.nz/forums/showthread.php/105096-Hyosung-gt250-not-shifting
https://www.youtube.com/watch?v=_Lt7zY5AYto
HYOSUNG GT 650 Service Manual
https://alpha-sports.com/hyosung_parts.htm
HYOSUNG GT 650 Manual

2005 Hyosung GT... | Answered on Jun 18, 2019


Hi, Mrdanamwood for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Hyosung, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?sa=X&q=Replace+the+handlebars+2005+Hyosung+GT650R&tbm=isch&source=univ&ved=2ahUKEwingdfIyvLiAhWxzlkKHe3jAZAQsAR6BAgDEAE&biw=1440&bih=757
https://www.youtube.com/watch?v=nh_IEVzdV9g
HYOSUNG GT 650 Service Manual
https://alpha-sports.com/hyosung_parts.htm
HYOSUNG GT 650 Manual

2005 Hyosung GT... | Answered on Jun 18, 2019


Hi, Anonymous if you have changed your engine size, compression ratio, fuel delivery system, air filter size or flow rate, mufflers or exhaust system or a significant change in altitude your carburetors need re-tuning and if your fuel system (gas tank, filters, fuel valve, and carburetor) is contaminated with ethanol sludge, varnish, rust, dirt, water, etc. or your bike has been sitting for months or years without running these components must be "PROPERLY" cleaned and reassembled "CORRECTLY" before any adjustments can be made. Tuning your carburetor is fairly simple once you understand the basic principals. Your engine is a simple airbox sucking air in and blowing it out, it is finely tuned at the factory for maximum performance once you upset that delicate balance by changing air filters, camshafts or exhaust systems your performance may go down the and the engine may run poorly, you need to compensate the air-fuel mixture in the carburetor in order for the engine to run smoothly and at peak performance. If you are running multi carburetors you need to sync them first and make sure your air cleaner element is clean and dry for paper elements or lightly oiled for foam and meshed elements and properly installed. Here is how and where you compensate trouble: "TIP" if your engine "BOGS" you're not getting enough fuel.
1. Close to 1/8 throttle is managed by the air screw and pilot/slow jet.
2. 1/8 to 1/4 throttle is managed by the air-screw, pilot/slow jet, and throttle slide.
3. 1/4 to 1/2 throttle is managed by the throttle slide and jet needle.
4. 1/2 to 3/4 throttle is managed by the jet needle, needle jet, main jet, and air jet.
5. 3/4 to wide open throttle is managed by the main jet and air jet.
6. A wide open throttle is managed by the main jet.
If you are running lean, spark plug electrode color is white, the engine runs hot and feels like it is starving for fuel you need to go up on the jet size or move the c-clip down one notch. If you are running rich, spark plug color is black or dark grey, the engine runs cool, and bogs down when accelerating you need to go down on jet size or move the c-clip up one notch. When your carburetor is properly tuned for maximum performance your spark plug electrode will be a light tan color like coffee with cream. If you prefer fuel economy over performance you can go down on main jet sizes until a satisfactory level of lower performance is acceptable versus MPH, your spark plug color will be whiter and your engine will run warmer. These tuning adjustments will only make improvements if your intake and exhaust system have no air leaks or sealing issues and the entire electrical system is in proper working order and you have no mechanical issues.
For more information about your issue and valuable "FREE" downloads that you will need for viewing and printing please click on the blue links below. Good luck and have a wonderful day.
https://www.youtube.com/playlist?list=PLkY9CF5JrijuE4BSXIxp-LcsyIz7W1Es7
http://korider.com/index.php?topic=7763.0
HYOSUNG GT 650 Service Manual
https://alpha-sports.com/hyosung_parts.htm
HYOSUNG GT 650 Manual

2005 Hyosung GT... | Answered on Jun 18, 2019


Hi, Anonymous before diagnosing any brake light issue always check the bulb and fuse first for integrity a brake light staying on is usually caused by the front brake light switch, which is mechanical, not disengaging. On early models moving the throttle control housing closer to the front brake master cylinder is the main fix. On late models, the switch gets tweaked and needs to be realigned. A brake light that does not come on when the brake lever is applied can be caused by a faulty switch or no continuity in the wiring at the switch. The rear brake light switch is hydraulic and it is extremely rare to malfunction in a closed circuit condition causing the brake light to stay on. Usually, rear brake light switch issues are caused by no brake pedal free play or a sticky rear master cylinder piston. A brake light that does not come on when the rear brake pedal is depressed can be caused by a faulty switch, air contamination in the brake line, or no continuity in the wiring at the switch. Finally, most tail light wiring harnesses run under the rear fender held in place by spot welded clips. Worn out rear shocks or lowered suspension can bottom out causing the rear tire to come in contact with the wiring harness, rubbing the insulation off, exposing the bare metal inner core, allowing it to break or short out.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
http://korider.com/index.php?topic=9863.0
Replace Motorcycle Rear Brake Light Switch
HYOSUNG GT 650 Service Manual
https://alpha-sports.com/hyosung_parts.htm
HYOSUNG GT 650 Manual

2005 Hyosung GT... | Answered on Jun 18, 2019


Hi, Phillip before testing any electrical component in the Charging System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
2. To check the regulator unplug it from the stator. Take a test light and clip it to the negative terminal of the battery and then touch first one pin and then the other on the plug that goes to the regulator. If you get even the slightest amount of light from the test light the regulator is toast.
To do this with a meter: black lead to battery ground, red lead to each pin on the plug, start with the voltage scale higher than 12vdc and move voltage scale down in steps for each pin. Any voltage is a bad regulator.
3. On the other part of the disconnected regulator plug. Set the multimeter for Ohms x1 scale and measure for resistance across the pins of the stator. You should read something around 0.1 to 0.2 ohms for a 32 amp system.
4. Then check for continuity between each pin on the plug and frame/engine ground. The meter needle should not move (infinite resistance)(digitals will show infinite resistance) if the meter needle does move (indicating continuity)(digitals will show some resistance), recheck very carefully. If the meter still shows continuity to ground the stator is shorted (bad).
5. Set the meter to read A/C volts higher than 30 volts (the scale setting for voltage should always be higher than the highest voltage you expect or you may fry the meter). Start the bike, and measure from one pin to the other on the plug (DO NOT cross the multimeter probes! - touch them to each other). You should read roughly 16-20 vac per 1,000 rpm.
6. If the battery was good under load test, if the stator is NOT shorted to ground, and the stator is putting out A/C voltage, then the regulator is bad (most likely even if passed step 2)
For more information about your question and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Hyosung Gt650R battery not staying charged
How to Fully Troubleshoot Your Motorcycles Charging System MotorcycleMD
HYOSUNG GT 650 Service Manual
https://alpha-sports.com/hyosung_parts.htm
HYOSUNG GT 650 Manual

2005 Hyosung GT... | Answered on Jun 18, 2019


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Hyosung, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.manualslib.com/manual/1018449/Hyosung-Aquil-Gv650.html?page=120
How to replace motorcycle water pump chain tensioner
How To Rebuild An ATV Motorcycle Water Pump
HYOSUNG GT 650 Service Manual
https://alpha-sports.com/hyosung_parts.htm
HYOSUNG GT 650 Manual

2005 Hyosung GT... | Answered on Jun 18, 2019


Hi, Michelle and the usual suspects are:
1. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
2. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Faulty main circuit breaker and or connections.
4. Faulty ignition coil and or connections.
5. Faulty spark plug, oil or gas fouled, wrong heat range or service type, wrong gap, loose in the cylinder head, broken electrode or insulator.
6. Faulty spark plug cables, leaking or broken, internal damage check for spark leakage in the dark.
7. Faulty ignition module, switch, CKP, MAP, CMP, sensor and or any connector in the ignition circuit could have corroded, loose, or broken pins/sockets
8. Burnt exhaust valve or air leak in the exhaust system.
9. Improper valve clearance (too tight).
10. Check for generated diagnostic codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.flickr.com/groups/501290@N25/discuss/72157607336392431/
http://korider.com/index.php?topic=29531.0
https://www.youtube.com/watch?v=eSky1ZfHdhA
HYOSUNG GT 650 Service Manual
https://alpha-sports.com/hyosung_parts.htm
HYOSUNG GT 650 Manual

2005 Hyosung GT... | Answered on Jun 18, 2019


Hi, Natal and the usual suspects are:
1. Low coolant level.
2. Restricted radiator air flow.
3. Faulty thermostat.
4. Coolant pump or fans inoperative.
5. Vent hose crimped.
6. The air in the coolant and needs bleeding.
7. Engine idling too long or bike moving too slow.
8. Coolant too old needs to be replaced.
9. Faulty temperature sensor, wiring or connector.
10. Radiator veins clogged or corroded needs repair
11. Cooling system leak.
12. Ignition timing retarded.
13. Spark plug heat range too high.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://korider.com/index.php?topic=23356.0
Overheating Help troubleshoot my bike
HYOSUNG GT 650 Service Manual
https://alpha-sports.com/hyosung_parts.htm
HYOSUNG GT 650 Manual

2005 Hyosung GT... | Answered on Jun 18, 2019


Hi, Anonymous before testing any electrical component in the Charging System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
2. To check the regulator unplug it from the stator. Take a test light and clip it to the negative terminal of the battery and then touch first one pin and then the other on the plug that goes to the regulator. If you get even the slightest amount of light from the test light the regulator is toast.
To do this with a meter: black lead to battery ground, red lead to each pin on the plug, start with the voltage scale higher than 12vdc and move voltage scale down in steps for each pin. Any voltage is a bad regulator.
3. On the other part of the disconnected regulator plug. Set the multimeter for Ohms x1 scale and measure for resistance across the pins of the stator. You should read something around 0.1 to 0.2 ohms for a 32 amp system.
4. Then check for continuity between each pin on the plug and frame/engine ground. The meter needle should not move (infinite resistance)(digitals will show infinite resistance) if the meter needle does move (indicating continuity)(digitals will show some resistance), recheck very carefully. If the meter still shows continuity to ground the stator is shorted (bad).
5. Set the meter to read A/C volts higher than 30 volts (the scale setting for voltage should always be higher than the highest voltage you expect or you may fry the meter). Start the bike, and measure from one pin to the other on the plug (DO NOT cross the multimeter probes! - touch them to each other). You should read roughly 16-20 vac per 1,000 rpm.
6. If the battery was good under load test, if the stator is NOT shorted to ground, and the stator is putting out A/C voltage, then the regulator is bad (most likely even if passed step 2)
For more information about your question and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Hyosung Gt650R battery not staying charged
How to Fully Troubleshoot Your Motorcycles Charging System MotorcycleMD
HYOSUNG GT 650 Service Manual
https://alpha-sports.com/hyosung_parts.htm
HYOSUNG GT 650 Manual

2005 Hyosung GT... | Answered on Jun 18, 2019


Hi, Anonymous and the usual suspects are:
1. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
2. Failed alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. A failed main circuit breaker or ignition switch, check for loose connections and continuity.
5. Failed system and or ignition relay, check for continuity.
6. Failed ignition coil, stator, magneto, ignition/electronic module.
7. Failed CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Faulty neutral, side stand or clutch lever safety switch.
10. Faulty or corroded kill switch.
11. Accelerator pump damaged or not working.
12. Water or dirt in the fuel system, carburetor or filter.
13. Restricted, blocked or kinked fuel line.
14. Fuel tank empty.
15. The gas cap is not venting properly or fuel tank venting system blocked, loosen the gas cap and go for a test ride.
16. A failed fuel pump, pressure regulator and or fuel injectors.
17. Vacuum line from the intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
18. Needle and seat stuck closed in the float bowl.
19. Petcock clogged or damaged.
20. Lean angle switch is faulty or needs adjustment.
21. Catastrophic engine failure, perform a compression test.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.flickr.com/groups/501290@N25/discuss/72157607336392431/
http://korider.com/index.php?topic=19881.0
HYOSUNG GT 650 Service Manual
https://alpha-sports.com/hyosung_parts.htm
HYOSUNG GT 650 Manual

2005 Hyosung GT... | Answered on Jun 18, 2019


Hi, Anonymous engine "BOG" is mainly caused by a rich air and lean fuel condition but it can also be caused by a lean air and rich fuel condition this situation rarely occurs and is only caused by the misinformed weekend warrior that owns a toolbox. If the bike has been sitting for months or years you will have to completely disassemble the carburetor and submerge the parts (except rubber parts) in "Carburetor Dip" It usually comes in a gallon bucket with a wire mesh basket that can be purchased at any automotive store. If it is not the above scenario then the following explanation will apply.
The more you open your throttle the more vacuum you are creating in your carburetor venturi and your intake manifold. When you are operating at higher RPM any unmetered air that leaks into your system can become more obvious.
Unmetered air is the air that is getting into your system after the fuel has been delivered. If you have unmetered air getting into your system between the butterfly/slide of the carburetor and the cylinder head this will create a lean condition.
All of the rubber components of the fuel system like vacuum hoses and intake manifold that you mount the carburetor to are made of rubber. If none of these components has been changed they are more than likely highly degraded and probably cracked in places to allow unwanted-unmetered-contaminated air into the combustion chamber. Check all of your vacuum lines and vacuum plugs for carburetor synchronization. The vacuum plugs are in the head just after the rubber intake manifolds. The petcock has a vacuum line as well as part of the emission system.
1. Check the intake manifold for fissures.
2. Ensure the bands used to tighten the manifolds down on the intake are secure and have not bound up the manifold.
3. Make sure air box fittings are not warped and fit completely over the carburetor.
Your airbox is metering air and is the first step in the process of consuming air and fuel. The system requires the resistance of the air filter in order to get the proper vacuum to "SUCK" the fuel out of the float bowl and create the proper venturi effect.
Improper mounting and sealing of the airbox will create a small lean effect. This might seem like no big deal but you are inviting dust and debris in your engine that is doing slow damage by not having proper fitment. Fix it so you know it's not contributing to your issue. Pick the low-hanging fruit first.
Do not go and start adjusting anything at this point. It ran fine before. There is something wrong with the assembly or a component. Do not adjust your floats. Get it back to where it was. The moment you start tweaking everything is the moment you lose OEM settings which are a must-have for fine-tuning and maximum performance.
Fine-tuning your carburetor and multi carb syncing come at the very end following the proper procedure established by the Carburetor Gods.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.600rr.net/vb/62-troubleshooting/200297-what-would-cause-my-bike-lose-power-sputter-while-riding.html https://www.flickr.com/groups/501290@N25/discuss/72157607336392431/
HYOSUNG GT 650 Service Manual
https://alpha-sports.com/hyosung_parts.htm
HYOSUNG GT 650 Manual
https://www.600rr.net/vb/62-troubleshooting/200297-what-would-cause-my-bike-lose-power-sputter-while-riding.html

2005 Hyosung GT... | Answered on Jun 15, 2019


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Hyosung, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.manualslib.com/manual/406860/Hyosung-Gt-650-Efi.html?page=45
Easy Oil Level Check
HYOSUNG GT 650 Service Manual
https://alpha-sports.com/hyosung_parts.htm
HYOSUNG GT 650 Manual

2005 Hyosung GT... | Answered on Jun 14, 2019


Hi I have a 2011 EFI Hyosung gt650. I have just removed fuel tank to replace rear shock. All parts refitted. And now I can't start bike. I have the bike turning over but no brrrrm. Have rechecked the fuel lines are fitted correctly. But still no go. Any ideas please.
Thanks.

2005 Hyosung GT... | Answered on Mar 09, 2019


If the bike is a carburettor model you need to clean your jets. Sounds though you have blocked main jet. Im guessing bike has sat for a while at some stage.....

2005 Hyosung GT... | Answered on Feb 16, 2018


Sounds to me like the starter motor is jamming, the clicking is the solenoid working so thats ok. Remove the starter motor and connect direct to a battery but be carefull as if it does run it will jump out of your hand so best to clamp it to a bench. If it is ok its probably the sprag clutch thats jammed. Good luck

2005 Hyosung GT... | Answered on Oct 02, 2017

Not finding what you are looking for?
2005 Hyosung GT 650 R Logo

108 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Hyosung Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5971 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

ROB

Level 3 Expert

858 Answers

Are you a Hyosung Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

GT 650 R Hyosung

  • GT 650 R Hyosung

Most Popular Question

breaker box hyosung

  • Motorcycles
Loading...