20 Most Recent 2000 Harley Davidson FLHT Electra Glide Standard Questions & Answers


Hi, Bill and the usual suspects are:
1. Fouled spark plugs.
2. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Open-short-ground in the wiring between the alternator to the ignition module/CDI box to the ignition coil.
5. Faulty pins or sockets in the plug connectors.
6. Spark plug cables in bad condition, shorting/leaking, spark plug cable connections loose check for spark leakage in the dark.
7. Faulty ignition coil or electronic control module/CDI box.
8. Faulty pulse coil.
9. Faulty CKP, CMP, or BAS sensor.
10. Faulty ignition switch.
11. Faulty run/off switch
12. Tilt sensor needs a reset.
13. Security alarm failing to disarm needs reset
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Bike will not start No spark Harley Davidson Forums 2000 Harley Touring Service Manual pdf http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc https://www.carlsalter.com/mcpdf/Harley%20Davidson-1970-03%20Owners%20Manual.pdf Instant Repair Help over the Phone to speak to me personally $4

2000 Harley... | Answered on Nov 05, 2018


Hi, Frances fuse and circuit breaker location are as follows:
SPORTSTER-Underneath the seat or behind the left side panel or inside the headlight bucket.
SOFTAIL-Underneath the seat behind the battery or under the speedometer housing.
DYNA-Behind the left side panel.
TOURING-Under speedometer housing or left and right side panel.
Under the speedometer housing or inside the headlight bucket location is for mechanical circuit breakers only.
The following is an approximate timeline of Circuit Breakers and Fuses.
1965-1990 circuit breakers only.
1990-2000 circuit breakers and fuses.
2000 and up fuses only.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Main circuit breaker location Harley Davidson Forums
Harley Davidson Touring FL Models Workshop Service Repair Manual 1999 $9 very cheap
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
https://serviceinfo.harley-davidson.com/sip/vehicle/lookupForm free owners manual
Instant Tech Relief To speak to me personally $6 very cheap

2000 Harley... | Answered on Feb 25, 2018


Hi, Bob for this scenario you will need your service, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere $9 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Harley Davidson Starter Replacement Install Starter Clutch FIX Complete...
Harley Davidson Touring FL Models Workshop Service Repair Manual 2000 $9 cheap
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
http://www.harley-davidson.com/content/h-d/en_US/home/owners/maintain-your-bike/owners-manual.html
Instant Tech Relief To speak to me personally absolutely "FREE"

2000 Harley... | Answered on Aug 17, 2017


Hi, David for more information about your issue and valuable "FREE" downloads that you will need please click on the links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a nice day.
2000 Harley Davidson FLHT Electra Glide Standard
Harley Davidson Touring FL Models Workshop Service Repair Manual 2000
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
http://www.harley-davidson.com/content/h-d/en_US/home/owners/maintain-your-bike/owners-manual.html
Instant Tech Relief A must have !!! Absolutely "FREE"

2000 Harley... | Answered on Jan 28, 2017


Hi, Charlie and the usual suspects are:
1. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
2. Failed alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. Failed main circuit breaker or ignition switch, check for loose connections and continuity.
5. Failed system and or ignition relay, check for continuity.
6. Failed ignition coil, ignition/electronic module.
7. Failed CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Air/fuel mixture screw improperly adjusted.
10. Accelerator pump damaged or not working.
11. Water or dirt in the fuel system, carburetor or filter.
12. Restricted, blocked or kinked fuel line.
13. Fuel tank empty.
14. The gas cap is not venting properly or fuel tank venting system blocked.
15. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
16. Needle and seat stuck closed in the float bowl.
For more information about your issue and valuable "FREE" downloads that you need please click on the links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a nice day.
https://www.reddit.com/r/Harley/comments/35afwv/bike_just_randomly_dies_out_while_riding_and
Harley Davidson Touring Models Workshop Service Repair Manual 2001
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
http://www.harley-davidson.com/content/h-d/en_US/home/owners/maintain-your-bike/owners-manual.html
Instant Tech Relief A must have !!! Absolutely "FREE"

2000 Harley... | Answered on Jan 08, 2017


Hi Dancarothers, it's too bad you can't find the very first and best tool you ever bought for your Harley Davidson. Despair not, for a mere $6.50 you may be able to download another one from the website below and good luck. Harley Davidson Manuals Mark Workshop

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2000 Harley... | Answered on Jun 21, 2015


Hi Pj31alby, and the usual suspects are:
1. Plugs in bad condition or partially fouled.
2. Spark plug cables in bad condition or leaking.
3. Spark plug gap to close or to wide.
4. Faulty ignition coil, module and or sensor.
5. Battery nearly discarged.
6. Damaged wire or loose connections at battery terminals especially the negative cable at "BOTH" ends, ignition coil, or plug between ignition sensor and module.
7. Intermittent short circuit due to damaged wire insulation.
8. If your bike has a CKP sensor you must leave both plugs in
head and check for spark with a 3rd plug.
For a prime suspect please visit website below. Good luck and have nice day.Harley Davidson Wiring Diagrams and Schematics
Big Twin Carb EFI DTC Intructions codes Harley Davidson Forums Harley...

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2000 Harley... | Answered on Jun 21, 2015


Hi Mark, for more information about your question please visit the websites below. Good luck and have nice day.
How To Adjust The Primary Chain On Harley Davidson Evolution Big Twin...

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


2000 Harley... | Answered on Jun 21, 2015


Hi Anonymous, the HD 6R12 spark plug is gapped at .040" Have nice day.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2000 Harley... | Answered on Jun 21, 2015


Hi Swood77, when checking for spark the CKP needs to measure the compression bump in order to send the correct signal to the ICM/ECM so always check for spark with either a third plug grounded or lift the end of the plug boot 1/2 " off one of spark plugs that are in the head. and the usual suspects are:
1. Fuel tank empty
2. Fuel supply valve turned off.
3. Fouled spark plugs.
4. Engine flooded with gasoline as a result of over use of enrichner.
5. Fuel valve or filter clogged.
6. Vacuum hose to automatic fuel supply valve disconnected, leaking, or pinched.
7. Discharged battery, loose or broken battery connections especially the negative cable at "BOTH" ends
8. Loose wire connection at coil, battery or plug between ignition sensor and module.
9. Spark plug cables in bad condition and shorting, spark plug cable connections loose,
or cables connected to wrong cylinders.
10. Ignition timing incorrect due to faulty ignition coil, ignition module, or sensors " Manifold Absolute Pressure" "Camshaft Position Sensor" "Crank Position Sensor" "Brake Apply Sensor
11. Engine lubricant to heavy ( winter operation )
12. Sticking or damaged valves or push rod wrong length.
13. Primary cam sproket spline sheared or missing spacer.
14. Security alarm system not disarming.
For a primary suspect please visit the website below. Good luck and have nice day.
Big Twin Carb EFI DTC Intructions codes Harley Davidson Forums Harley...
Set Change Override Transport Harley Security Alarm PIN Code No Key Fob...

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


2000 Harley... | Answered on Jun 21, 2015


Hi Johnny_warne, and the usual suspects are:
1. Wheels and or tires unbalanced, worn or damaged.
2. Engine/transmission/vehicle not aligned properly.
3. Primary chain badly worn or links tight as a result of insufficient lubrication or misalignment.
4. Engine to transmission mounting bolts loose.
5. Upper engine mounting bracket loose.
6. Ignition timing incorrect/poorly tuned engine
7. Internal engine problem/ flywheel shift runout should be .003" max.
8. Broken frame
Good luck and have nice day.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2000 Harley... | Answered on Jun 21, 2015


Hi S_biestek, it's too bad you can't find the very first and best tool you ever bought for your Harley Davidson. Despair not, for a mere $6.50 you may be able to download another one from the website below and good luck. Harley Davidson Manuals Mark Workshop

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2000 Harley... | Answered on Jun 21, 2015


Hi Douthett, for more information about your question please visit the websites below. Good luck and have nice day.
ACCEL Motorcycle Electrical Batteries

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2000 Harley... | Answered on Jun 21, 2015


Hi Anonymous, for more information about your question please visit the websites below. Good luck and have nice day.
https://www.youtube.com/watch?v=nUTkCXV7nME

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


2000 Harley... | Answered on Jun 21, 2015


Hi Anonymous, the OEM push rods on your year and model are non adjustable but you do have 4 options for noisy lifters:
1. with engine at operating temperature do a quick series of 5 throttle revs to 1000 RPM'S below red line.
2. Try an engine oil additive Liquid Molly Tappet Stop Noise or Risoline Engine Treatment.
3. Cut out stock push rods with bolt cutters, remove suspect lifter, disassemble lifter and clean with carb cleaner and compressed air especially under the lifter check plate, reassemble and install, replace push rods with Taper Lite Adjustable push rods.
4. Buy new lifters.
Good luck and have nice day.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2000 Harley... | Answered on Jun 21, 2015


Hi Anonymous, for more information about your question please visit the websites below. Good luck and have nice day.
Uninstall remove Install replace front fairing speakers on Harley Davidson...

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


2000 Harley... | Answered on Jun 21, 2015


Hi Joan9, seat removal can range from the simple and obvious to the complex and baffling for the novice new Harley Davidson owner. Seems like the more expensive the bike is the harder it is to remove the seat. So let's start with the most expensive. 99% of all Harley seats have a male tounge in the front that slides into a female reciever that is either bolted or welded to the frame just behind the fuel tank. For this reason when ever you are removing a seat you must always slide it backwards 3-5 inches. Next they may may have a bolt on each side usually under a flap on the seat. Then there is the seat strap that is secured on both sides, only one side needs to be removed. A single phillips head bolt can secure it to the rear fender or it may have a bracket with two studs secured by nuts or knobs to fasten the rear portion of the seat. On newer model short seats there may be a "T" stud that locks in the rear portion of the seat just a few inches in front of the rear seat bolt, you have to push forward and lift up after you remove the bolt. If you have a pillion pad or passenger seat that snugs up against the front seat there can be a bolt securing the two to the rear fender, you have to get your hand in between the two seats and force seperation of seat material to see and gain acess to the bolt. Finally there is the rear seat bolt in the back that is the caboose of seat fasteners, usually a large chrome bracket, that screws into the rear fender. Care must be exercised in covering this shinny bauble with your hand during the sliding back procedure so as to NOT scratch the tour pak. So when all the hidden and mysterious fasteners have been removed, it's lift up in the rear, slide backwards a few inches and bingo you have mastered the impossible. Good luck and have nice day.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2000 Harley... | Answered on Jun 21, 2015


Hi Anonymous, for more information about your question please visit the websites below. Good luck and have nice day.
Cycles Tech Tips Capacities and Fluid Requirements

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2000 Harley... | Answered on Jun 21, 2015


Hi Anonymous, 48 oz. HD Primary Chaincase Lubricant. Have nice day.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2000 Harley... | Answered on Jun 21, 2015


Hi Anonymous, for a free wiring diagram please visit the website below and good luck.
Harley Davidson Wiring Diagrams and Schematics

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2000 Harley... | Answered on Jun 14, 2015

Not finding what you are looking for?
2000 Harley Davidson FLHT Electra Glide Standard Logo

93 questions posted

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6080 Answers

Mike

Level 3 Expert

4367 Answers

Marvin
Marvin

Level 3 Expert

85219 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

FLHT Electra Glide Standard Harley Davidson

  • FLHT Electra Glide Standard Harley Davidson

Most Popular Question

starter drive gear located 2000electra

  • Motorcycles
Loading...