20 Most Recent 1998 BMW R 1100 R - Page 3 Questions & Answers

0helpful
1answer

2014 bmw 1200rt motorcycle, while ridding the suspension went solid on strapping it down on a trailer it freed off with a bang any thoughts is it safe to ride ? thanks.

Hey Robin, When you collapsed your suspension, it hydraulically "locked" down.. now that it has returned to normal, it should be OK...as long as it works smoothly and does not bind... ....be careful.. rubber side down=always!!
7/4/2017 1:21:48 PM • BMW Motorcycles • Answered on Jul 04, 2017
tip

BMW Motorrad Fault Codes

10167 Output stage to electric fuel pump GS/A 1200 Idling irregular Battles to start Fault appears to start intermittently Bike may start and ride, then will appear to have fuel starvation This unit is situated on the left side of the tank. It is a little aluminium unit with fins on. Check the o-ring of this unit. Unscrew the unit and check for moisture in the cavity below it. Use moisture repellent spray and contact cleaner to clean this device. If problem solving does not work then replace the unit. 10218 CAN-Bus Timeout: No communication with KOMBI (Instrument cluster) control unit GS/A 1200 Test with diagnostic system. Clear fault code. 10219 CAN-Bus Timeout: no communication with ZFE (Central vehicle electronics) control unit GS/A 1200 Instrument cluster does not activate properly. Instrument cluster activates partially and then fades away. May start on intermittent occasions Test with diagnostic system. If all else fails replace the ZFE control unit. (Very expensive). 10444 Fuse activated for component block 3 (starter relay, Immo (EWS) ring aerial, ignition coils, injectors) GS/A 1200 There may be a short on the battery terminals or elsewhere. Can happen in conjuction with fault code 10219. 23971 Rear wheel speed sensor: Signal implausible GS/A 1200 Possible dirt on sensor. Dirt on wheel where sensor lost contact. Test with diagnostic system. Clear fault code. Replace sensor if fault code reappears. 24052 Electric System under-voltage GS/A 1200 Starter motor battles to turn Instrument cluster fades and then reappears. Check Battery Voltage Check that the alternator is charging battery Check wiring to see that a short is not draining battery power. Replace battery if it is not charging or Service alternator 24971 Pressure In Front Wheel Circuit To High GS/A 1200 Check Wheel Pressure! Release air out of front wheel to the correct pressure. Clear Fault Code Oter fault codes here http://bike-manual.mozello.ru/bmw-motorrad-fault-codes
on Dec 20, 2016 • Motorcycles
0helpful
1answer

BMW f650 funduro oil sump plug rotates but won't come out

The threads are bad. If you cannot get under the head of the plug or use vice grips to pull it out, then you are going to have to remove the whole sump pan.
10/21/2016 4:48:35 PM • BMW Motorcycles • Answered on Oct 21, 2016
0helpful
1answer

Hi Gregg BMW K1200LT O2 Sensor. Thanks for your answer. Both Failures occurred during normal riding, is there a way to test the sensor as I know they are extremely sensitive regards Alan

if you can get the specifications they can be tested ( best done by a service center with the equipment) generally a clean using vinegar will remove the oxide build up that affects their performance unless it is a wiring problem in which case , replacement will be required be careful as there are 2 oxygen sensors in use one has 4 wires and is a heated oxygen sensor and the other is an oxygen sensor with 2 wires
6/18/2016 7:28:48 AM • BMW Motorcycles • Answered on Jun 18, 2016
0helpful
1answer

What is the intake and exhaust valve adjustment for a !992 Bmw R100RT mono

Cold engine set valve clearance at: 0.10 mm intake or about .003" inch. 0.20 mm exhaust or about .007" inch. ---
4/19/2016 10:09:09 PM • BMW Motorcycles • Answered on Apr 19, 2016
0helpful
1answer

Hi my gs1150 2002 got a light vibration it feels

Had the same problem with my R80RT 1986 model .Suggest to drain the gearbox oil ,if it looks like metal flake paint then definitely bearings . In my case it was the output shaft rear bearing , I replaced all the bearings (except the main bearing on the input shaft because to replace this one requires replacing the shaft as well many dollars) my bike had done 275k K/m (170k miles)
4/19/2016 3:03:49 PM • BMW Motorcycles • Answered on Apr 19, 2016
0answers
0helpful
1answer
Not finding what you are looking for?
1998 BMW R 1100 R Logo

Popular Tags

8 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top BMW Experts

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Sean Wright
Sean Wright

Level 3 Expert

2045 Answers

xxxxxx xxx

Level 3 Expert

5117 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

R 1100 R BMW

  • R 1100 R BMW

Most Popular Question

1997 bmw r1100r front tyre scuffing rhs

  • Motorcycles
Loading...