20 Most Recent 2003 Harley Davidson FLHTC Electra Glide Classic Questions & Answers


It could well be a fuse problem .Contact you local harley agent and ask where is the fuse box located for this bike ,

2003 Harley... | Answered on Sep 02, 2018


behind the left hand cover below seat, some early models also have a cut ot /overload in the same location this should reset itself when whatever is causing the problem is cured good luck Michael

2003 Harley... | Answered on Apr 19, 2016


Hi Kenmccan, I'm guessing a sticky lifter, try some Rislone engine oil treatment you can pick it up at any auto parts store and it works really great. Good luck and have nice day.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2003 Harley... | Answered on Jun 25, 2015


Hi Langskip, try replacing your fuel pump relay located behind the right side panel. Good luck and have nice day.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2003 Harley... | Answered on Jun 25, 2015


Hi P51ace, unplug it and unscrew it. Have nice day.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2003 Harley... | Answered on Jun 25, 2015


Hi Klimb2hi, replace your ignition relay, Have nice day.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2003 Harley... | Answered on Jun 25, 2015


Hi Bob, only thing left is the bulbs. Good luck and have nice day.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2003 Harley... | Answered on Jun 25, 2015


Hi Anonymous, here are your axle torque specifications for all late models 2000 and up where applicable.
1. Front axle nut 50-55 ft lbs.
2. Front fork slider cap nuts 11-15 ft lbs.
3. Front fork pinch bolt 30-35 ft lbs.
4. Rear axle nut 60-65 ft lbs.
Good luck and have nice day.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2003 Harley... | Answered on Jun 25, 2015


Hi Kristopher, for more information about your question please visit the websites below. Good luck and have nice day.
Harley Diagnostic Codes 04 to Present

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2003 Harley... | Answered on Jun 25, 2015


Hi Sargesmit845, perform the following tests:
1. Fill acid type batteries to proper levels.
2. Charge battery overnight at 1-2 amps you need 12.5 volts or better after charging.
3. Hook up battery positive cable, then with your multimeter on the milliamp scale connect one lead to the negative battery post and the other lead to the ground cable. Meter should read 3 milliamps or less, 10 milliamps with a radio, 15 milliamps with radio and CB. If your meter reads higher you need to isolate the circuit by pulling fuses and circuit breakers one at a time and observe meter for drop in aprerage then get out your test light and track down the short in that circuit.
3. Make sure all connections are clean and tight especially the negative cable at "BOTH" ends.
4. Hook up volt meter to battery and start engine, if meter falls below 9.5 v while cranking replace battery.
5. With engine running at 3600 RPM battery should read 14.3-14.7 volts if not continue tests.
6. Unplug voltage regulator from alternator at crankcase by front of primary cover.
7. To test voltage regulator go to: https://www.youtube.com/watch?v=F8EjV0IjW9Q
8. With ohm meter, one lead grounded, touch alternator pin meter should read infinity, if not replace stator.
9. With ohm meter, both leads touching alternator pins meter should read 0.1 to 0.2 ohms on 1989 and later models. 0.2 to 0.4 ohms 1988 and earlier models, if not replace stator.
10. With volt meter set on AC scale, both leads touching alternator pins meter should read
16 to 20 volts AC for every 1000 RPM'S 1989 and later and 19 to 26 volts AC for every 1000 RPMS. If not replace rotor.
17. For a free wiring diagram please visit the website below. Good luck and have nice day.
Harley Davidson Wiring Diagrams and Schematics

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2003 Harley... | Answered on Jun 25, 2015


Hi Anonymous, for more information about your question please visit the websites below. Good luck and have nice day.
Motorcycle Repair Adjusting the Rear Suspension Air System Shocks on...

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


2003 Harley... | Answered on Jun 25, 2015


Hi Anonymous, EFI models do not have fuel valves/petcocks, for more information about your question please visit the websites below. Good luck and have nice day.
Harley Check Valve Rebuild Kit

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


2003 Harley... | Answered on Jun 25, 2015


Hi Robin, maybe the transmission don't worry about you will be fine. Have nice day.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2003 Harley... | Answered on Jun 25, 2015

Not finding what you are looking for?
2003 Harley Davidson FLHTC Electra Glide Classic Logo

125 questions posted

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6080 Answers

Mike

Level 3 Expert

4367 Answers

Marvin
Marvin

Level 3 Expert

85219 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

FLHTC Electra Glide Classic Harley Davidson

  • FLHTC Electra Glide Classic Harley Davidson

Most Popular Question

oil leaking into carb

  • Motorcycles
Loading...