20 Most Recent
1986 Honda CBX 550 F-F2 Questions & Answers
I want to change my fork seal for Honda CBX550 Fours
Are you talking about the inner seals or outers seals ,either way its a long and labour intensive job.If you have never done it before then its best to get help from a friend ,Fitting the seals is quite easy ,its the stripping down that takes the time ,and how much oil to put in is found in your workshop manual .if you don't have a manual then you may find one in your local libary .
1985honda spree good spark wont
have you checked for good compression? maybe the piston rings a shot
also make sure that the exhaust is not blocked
where are you spraying the starting fluid? into the airbox or straight into the carb
the other thing you could try is removing the plug and spraying directly into the head the quickly replacing the plug and kicking the bike if this dosnt work then the ring are deffintly broken
hope this helps
John
My son just bought a
Is the sidestand down, some bikes have a safety interlock that kills the engine when the bike is put into gear with the sidestand down.
Honda PC50 moped VIN decoder
The serial number on a Honda PC50 moped typically contains important information about the vehicle, such as its manufacturing date and model information. Here's how you can read the serial number:
1. **Locate the Serial Number**: The serial number on a Honda PC50 moped is usually stamped on the frame of the vehicle. It may be located in different places depending on the year of manufacture, but common locations include the head tube or down tube near the handlebars.
2. **Understand the Format**: The serial number may consist of a combination of letters and numbers. It typically follows a specific format that provides information about the moped.
3. **Decode the Information**: While the format may vary slightly depending on the year of manufacture, Honda serial numbers often contain the following information:
- Year of Manufacture: The first few characters or digits may indicate the year of manufacture. For example, "73" could indicate that the moped was manufactured in 1973.
- Model Information: Following the year, there may be additional characters or digits that represent the model or variation of the moped.
4. **Consult a Reference Guide**: If you're having trouble deciphering the serial number, you can consult a reference guide specific to Honda PC50 mopeds. Online forums, enthusiast websites, or official Honda documentation may provide resources or guides to help you interpret the serial number.
5. **Contact Honda**: If you're still unsure about the information contained in the serial number, you can contact Honda directly or reach out to a Honda dealership for assistance. They may be able to provide you with additional information or help you decode the serial number.
By following these steps, you should be able to read and understand the serial number on your Honda PC50 moped, allowing you to gather important information about its manufacturing date and model.
4/23/2024 9:05:37 AM •
Honda...
•
Answered
6 hours ago
Honda 500 TRX fa6 has PS on the dash….what does it mean ?
The Power Steering has failed. There has been a factory recall for a suddenly failing electrical steering shaft, that could cause the rider to loose control. This does not have to be your problem but anyhow either the electronics or the pump failed. Error codes or messages usually have to be erased by a simple reset procedure or disconnecting a plug, after repairs are done.
3/31/2024 4:25:47 AM •
Honda...
•
Answered
on Mar 31, 2024
Hiss works but
On the bottom of your speedometer on the left side there is 2 buttons
press the far left one for a couple of seconds and the light should go on
1/8/2024 6:42:24 AM •
Honda...
•
Answered
on Jan 08, 2024
What to torque the head on my 99 CBR 929 Honda in
For a 1999 Honda CBR929RR, the cylinder head bolt torque specifications are essential to ensure proper engine assembly and function. When tightening the cylinder head bolts, it's crucial to follow the manufacturer's recommended torque settings to prevent damage to the engine components.
For the CBR929RR, the cylinder head bolt torque specifications are typically as follows:
1. **Initial Torque:** 29 Nm (2.9 kgf-m, 22 ft-lbs)
2. **Final Torque:** 64 Nm (6.4 kgf-m, 47 ft-lbs)
It's essential to tighten the cylinder head bolts in the specified sequence and in multiple stages, gradually increasing the torque until reaching the final specified torque. The exact tightening sequence can usually be found in the service manual specific to your motorcycle model.
When torquing the head bolts, ensure you're using a reliable torque wrench calibrated in the appropriate units (Nm or ft-lbs). Always follow the tightening sequence precisely to ensure even pressure distribution across the cylinder head gasket.
Additionally, it's advisable to use new cylinder head bolts if the old ones have been previously tightened or stretched beyond their yield point. This helps maintain proper clamping force and ensures the integrity of the engine assembly.
As always, referring to the service manual or consulting a professional mechanic experienced with motorcycle engine assembly can provide additional guidance and ensure the correct torque settings are applied during the cylinder head installation process.
12/10/2023 4:27:33 AM •
Honda...
•
Answered
on Dec 10, 2023
2006 Honda Shadow Arrow 750 VT missing on the rear cylinder fire
. One possibility is that the spark plug or plug wire is faulty 1. Another possibility is that the carburetor needs cleaning and adjustment It could also be due to a valve adjustment issue or a bent rod.
I would recommend taking your motorcycle to a professional mechanic who can diagnose and fix the issue. If you prefer to troubleshoot it yourself, you can start by checking the spark plug and plug wire for any damage or wear and cleaning the carburetor. However, please note that working on a motorcycle engine can be dangerous and requires specialized knowledge and tools. Please take all necessary safety precautions and follow the manufacturer's instructions when working on your motorcycle.
10/22/2023 2:01:22 PM •
Honda...
•
Answered
on Oct 22, 2023
2007 honda shadow vt750 dies sputters on acceleration
The problem might be with the air filter, and if not there are a few other things that could be causing your Shadow engine to bog down on acceleration. This includes a dirty carburetor, carb adjustment issues, or other internal problems like damaged vacuum lines or a cracked manifold
8/31/2023 7:57:51 AM •
Honda...
•
Answered
on Aug 31, 2023
Not finding what you are looking for?