1987 Honda GL 1200 Interstate Gold Wing - Page 7 - Answered Questions & Fixed issues


Hi, Anonymous para sa higit pang impormasyon tungkol sa iyong isyu at mahalagang "LIBRE" na mga pag-download na kakailanganin mo para sa pagtingin o pag-print mangyaring mag-click sa asul na mga link sa ibaba. Good luck at magkaroon ng isang kahanga-hangang araw. https://www.ultimatespecs.com/motorcycles-specs/um/honda-tmx-155-2013
Tmx 155 top speed part 3 by manalac
Honda tmx 155 motorcycle manual pdf
https://www.partsfish.com/page/oem-parts-for-honda
Road Motorcycles Owning Honda Honda MPE

Honda... | Answered on Jun 12, 2019 | 26 views


Hi, Anonymous it should be noted that the "AIR FUEL" mixture screw adjustment "ONLY" manages your idle and has no effect on any other circuit also any intake leaks must be repaired before the A/F adjustment procedure can be performed otherwise you will never obtain a proper idle and you will waste a lot of time chasing the impossible. The A/F mixture screw's purpose is to fine tune the fuel charge entering the combustion chamber. The following applies to both 2 and 4 stroke engines:
1. The mixture screw may be sealed at the factory with a Welch Plug please review the following video for removal.
https://www.youtube.com/watch?v=wAXcksgvDkM
2. The mixture screw manages a range of 3 complete 360-degree counterclockwise turns from the bottom/closed position.
3. The mixture screw should have a spring and o-ring for tension and sealing integrity.
4. Turn the mixture screw clockwise until it gently bottoms out, this makes the fuel charge very lean and the engine should not idle if it does then the pilot/idle jet is too big and needs to be replaced with the next size smaller.
5. Turn the mixture screw 1 and 1/2 turns counterclockwise to establish a baseline for starting the engine.
6. To fine-tune the idle circuit, adjust the mixture screw 1/4 turn in or out to achieve maximum idle RPM, wait 15 seconds between each adjustment for the idle to settle.
7. Never go past 3 full turns out this will make the fuel charge rich, foul plugs, and produce black smoke out of the exhaust, if the engine RPM keeps increasing past 3 turns the pilot/idle jet is too small and needs to be replaced with the next size larger.
8. After achieving maximum idle back out the mixture screw another 1/8 of a turn then adjust the throttle cable idle stop screw to 950-1050 RPM.
9. This procedure works great on 99% of all engines, for the 1% that demand a more robust throttle response on aftermarket monster fuel delivery systems additional tweaking outside the box may be necessary.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://www.400greybike.com/files/NC30%20Carb%20Jetting%20-%20DIY%20Guide.pdf
Pilot Jet idle Mixture Screw Settings
Honda VFR400R Service Manual
https://www.partsfish.com/page/oem-parts-for-honda
Road Motorcycles Owning Honda Honda MPE

Honda... | Answered on Jun 11, 2019 | 135 views


check the battery condition and voltage ,check the main fuse,before checking the starter coil and shooting coil.

Honda... | Answered on Jun 11, 2019 | 371 views


notify manufacturer

Honda... | Answered on Jun 11, 2019 | 40 views


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Motorcycle Fork Oil Change Part 1
Ask Dave Fork Oil Level
Honda XL 125 V1 Shop Manual
https://www.partsfish.com/page/oem-parts-for-honda
https://www.google.com/search?sa=X&q=2010+honda+125+estorm+owner%27s+manual&tbm=isch&source=univ&ved=2ahUKEwjOx7rHztbiAhUHxVkKHaLdCo8QsAR6BAgEEAE&biw=1440&bih=757

Honda... | Answered on Jun 07, 2019 | 383 views


Hello, I'm new here, honda tmx 155 my motor, my problem is that when I'm up I need one I need to keep the kick out of it, even if it's too long, my sprockets are 14/51, before the lining, when he comes up he's staring at it then suddenly, thank you for the answer ..

Honda... | Answered on Jun 02, 2019 | 31 views


Hi, Tony for more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.ebay.com/b/Motorcycle-Electrical-Ignition-Parts-for-Honda-XL250/179853/bn_20048893
https://www.ebay.com/b/Motorcycle-CDIs-ECUs-for-Honda-XL250R/177933/bn_19420278
https://sellfy.com/p/TxGl $20
https://www.partsfish.com/page/oem-parts-for-honda
Honda Degree XL250 Owner Manual

Honda... | Answered on Jun 01, 2019 | 458 views


Yes sir it has a wet clutch.

Honda... | Answered on May 31, 2019 | 37 views


Likely poor compression and in need of valve lash adjustment. Plenty of how to videos.

Honda... | Answered on May 31, 2019 | 94 views


I would like to help you. I need more info . What you are describing is not a mechanical question. please explain. Gas string is not a correct term, Thank you

Honda... | Answered on May 28, 2019 | 32 views


ddealer or authorized locksmith to have a key cut by vin

Honda... | Answered on May 25, 2019 | 33 views


This problem can occur on any bike that is carburetted and uses a needle and seat/float bowl system. Basically any bike that isn't fuel injected in other words. The reason fuel is being dumped is because it isn't getting shut off and is flowing past the needle/seat. The cause of this is one or more of the following. Dirt or foreign material interfering with needle/seat/float operation.....Worn needle and/or seat....Malfunctioning float due to leaking float...Is there any thing in the float when you shake it?......Lastly, and I cannot stress this point enough,.....Improper float level setting. This is a critical setting and must be set as accurately as possible according to manufacturer's specs. It is accomplished by bending the tang of the float which will control how much fuel will be in the float bowl when the float bowl is full. Think of a common toilet with a float mechanism because it is the same principle.

Honda... | Answered on May 23, 2019 | 326 views


Kimmo,
The tire pressure in the manual is 4.0 (four point zero) PSI..... NOT 40 PSI. You are lucky that the tire did not explode (yet)

Honda... | Answered on May 18, 2019 | 57 views


Check the timing, replace the plugs. If no better check the compression of each cylinder with a compression tool that replaces the spark plug. Pull all other plugs off while cranking motor. If compression is low on one or all, a valve might be open it rings are gone. If compression is good, if a carby make sure needle if free and bowl is not fill of oil from evaporated fuel.

Honda... | Answered on May 17, 2019 | 39 views


if you have not already replaced the element do that. if problem persists, remove and have the carb cleaned internally

Honda... | Answered on May 15, 2019 | 27 views


Usually 34-38 Psi depending on solo rider or 2 up.
Handy link for all Avon tyres below
https://www.avontyres.com/en-us/tyre-care/technical/tyre-pressure-guidelines

Honda... | Answered on May 14, 2019 | 16 views


Hi, Curt for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://thumpertalk.com/forums/topic/660645-1989-kx80-big-wheel-fork-oil-amount
Ask Dave Fork Oil Level
https://www.motosport.com/clymer-service-manual $20
Kawasaki KX60 Service Manual
https://www.partsfish.com/page/oem-parts-for-honda
Free Honda Motorcycle Service Manuals for download https://bikez.com/motorcycles/honda_cr_80_rb_expert_2002.php

Honda... | Answered on May 07, 2019 | 27 views

Not finding what you are looking for?
1987 Honda GL 1200 Interstate Gold Wing Logo

Popular Tags

14 questions posted

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6080 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

richard libby

Level 2 Expert

209 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...